XIGMATEK 2022-NEON LED CPU Liquid Cooler User Manual

XIGMATEK 2022-NEON LED CPU Liquid Cooler

Introduction

1. Keep and store the product away from the reach of children.
2. Check the component list and condition of the product before installation. If there is any problem, contact the shop where you purchased to get a replacement or refund.
3. Xigmatek Co., Ltd. is not responsible for any damages due to external causes, including but not limited to, improper use, problems with electrical power, accident, neglect, alteration, repair, improper installation, and improper testing.
4. CPU and motherboard are subject to damage if the product is incorrectly installed.

ACCESSORIES

NEON AQUA 360 ACCESSORIES

Installation Instructions

Intel LGA 115x/1200/1700

1. Insert screw bolts to Intel 1700 or 115x/1200 backplate mounting holes.

2. Install screw bolt washers to lock the screw bolts & backplate.

3. Make sure the screw bolt is locked in on the backplate.

4. Install the backplate to motherboard

• Remove the copper cold plate protective film.

• Install the Intel pump head mounting brackets.

1. Clean the CPU surface.

2. Apply and spread the thermal paste to the CPU evenly using the included spatula.

3. Place the stand-off to the backplate screw bolt.

4. Align the Intel pump head mounting brackets to the backplate screw bolts, then place the pump head on the CPU carefully.

5. Using spring screw nuts to complete the pump head and motherboard installation

NEON AQUA 240 ACCESSORIES

Intel LGA 2011/2066

• Remove the copper cold plate protective film.

• Install the Intel pump head mounting brackets.

1. Clean the CPU surface.

2. Apply and spread the thermal paste to the CPU evenly using the included spatula.

3. Align the Intel 2011/2066 pump head mounting brackets to backplate screw bolts, then place the pump head on the CPU carefully.

4. Using a spring screw to complete the pump head and motherboard installation.

AMD AM3/AM4 (MB Without Backplate)

1. Insert screw bolts to AMD AM3 or AM4/AM5 backplate mounting holes.

2. Install screw bolt washers to lock the screw bolts & backplate.

3. Make sure the screw bolt is locked in on the backplate.

4. Install the backplate to the motherboard

• Remove the copper cold plate protective film.

• Install the AMD pump head mounting brackets.

1. Clean the CPU surface.

2. Apply and spread the thermal paste to the CPU evenly using the included spatula.

3. Place the stand-off to the backplate screw bolt.

4. Align the AMD pump head mounting brackets to backplate screw bolts, then place the pump head on the CPU carefully.

5. Using spring screw nuts to complete the pump head and motherboard installation

CABLE & CONNECTOR INSTALLATION

1. Pump to Motherboard CPU Fan Socket (Please Set BIOS CPU Fan Speed at Full Speed Mode)
2. Pump LED to ARGB Control Box
3. ARGB Tube to ARGB Contro Box or Link with Pump LED 3P ARGB Connector
4. Control Box Power Cable to PSU
5. ARGB MB SYNC Signal to Motherboard ARGB Header
6. ARGB Fan to ARGB Control Box

GALAXY II FAN CONTROL BOX

1. Fan 1~8: 6Pin Port
2. Power: 4Pin Molex Power Connector (To PSU)
3. LED SPEED
4. MODE
5. FAN SPEED
6. LED: ARGB Port (Connect Other ARGB Accessories)
7. DATA: ARGB Port (Connect to ARGB Motherboard)
8. Reset SW: Connect to PC Case Reset Button To Change Color Mode

ARGB Control Box Power Consumption: Total 40W maximum
12V: Total 36W maximum
Caution: Please do not overpower the controller box, it is dangerous and might cause damage!

CAUTION

1. Please check your PSU 5V & 12V power output specification, make sure the PSU single 4pin Molex connector can support sufficient power output to avoid PSU cable overheating and meltdown.
2. Please use at least 450W PSU and 18AWG thickness 4Pin Molex cable if connect more than 6 fans.
3. It will NOT work with 4-pin RGB or 12V RGB fans or light stripes.

CAUTION
During installation when releasing the fan cable from the control box, please push the connector locking clip to avoid damage, do not pull the fan cable directly!

ARGB REMOTE CONTROLLER

CAUTION
To Sync with the ARGB motherboard, press the M/B SYNC button after connecting the fans and ARGB cable to the motherboard ARGB header.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>