TARAMPS CRX-4 Electronic 4 Way Crossover Rca Channels 8 Volts Rms Instruction Manual

TARAMPS CRX-4 Electronic 4 Way Crossover Rca Channels 8 Volts Rms

Specifications:

• Product: CRX-4 Crossover
• Manufacturer: Taramps Electronics Ltda
• Compliance: Directive 2014/30/EU, EN 50498:2010
• Country of Origin: Brazil

Product Usage Instructions

Safety Requirements
Before using the product, ensure you read the manual carefully to understand the safety precautions and symbols provided. Failure to adhere to safety instructions may result in injury or product damage.

Installation
The installation of the CRX-4 Crossover must be carried out by a qualified professional to ensure proper setup and functionality.

Warranty and Technical Assistance
For warranty terms and technical support, visit the manufacturer’s website at www.taramps.com.br/en/rede-de-assistencias-tecnicas or contact the factory support via phone at +55 18 3266-4050 / +55 18 99749-3391 or email at service@taramps.com.br.

Product Overview
The CRX-4 Crossover features multiple signal inputs and outputs for different audio frequencies. It includes ways filters and controls with LED indicators for easy monitoring.

Low Way Settings
The LOW way includes settings for Boost Freq., LPF, LEVEL, and more. Adjust these settings based on your audio preferences and system requirements.

• Boost Freq.: Set the frequency for BASS-BOOST operation.
• LPF: Adjust the upper cut-off frequency for the LOW way.
• LEVEL: Control the output level of the LOW channel.
• Additional settings for LOW MID way frequencies.

Frequently Asked Questions (FAQ):

• Q: Where can I find the EU Declaration of Conformity for the product?
  A: The full text of the EU Declaration of Conformity is available on the product page on the internet.

• Q: What should I do with the product at the end of its lifespan?
  A: Do not dispose of the product in household waste. Look for an electronic equipment collection or recycling center for proper disposal.

Term of warranty

TARAMPS, located on Abilio Daguano Street 274, Res. Manoel Martins – Alfredo Marcondes, SP – Brazil, ZIP CODE 19180-000, guarantees this product against any defects on terms of project, making, assembling, and/or with solidarity, due to project vices which cause it improper or inadequate to its original use within 12 months from the date of purchase. In case of a defect during the warranty period, TARAMPS’ responsibility is limited to the repairing or substitution of the device of its own making.

This warranty excludes:

• Damaged products by improper installation, water infiltration, violation by unauthorized individuals;
• Tamper or torn warranty seal;
• Cases in which the product is not used in adequate conditions;
• Defects caused by accessories, modifications or features attached to the product;
• The product with damage from falling, bumps or nature-related problems (flooding, lightning, etc.);
• Warranty card is not properly filled or torn;
• Costs involving uninstallation, reinstallation of equipment as well as shipment to the factory;
• Damage of any kind, due to problems in the product, as well as losses caused by discontinued use of the product.

Technical assistance

For international support, check on our website:
www.taramps.com.br/en/rede-de-assistencias- tecnicas or contact direct the factory support:
Phones: +55 18 3266-4050 / +55 18 99749-3391
E-mail: service@taramps.com.br

Introduction

Read this manual before installing the product. In case of questions contact our technical support
+55 (18) 3266-4050 or www.taramps.com.br.

Declaration of Conformity

TARAMPS ELECTRONICS LTDA Alfredo Marcondes – SP Brazil
Hereby, Taramps Electronics Ltda declares that the product CRX-4 complies with the Directive 2014/30/EU, according with the following harmonized standard:
EN 50498:2010
Electromagnetic compatibility (EMC) – Product family standard for aftermarket electronic equipment in vehicles
The full text of the EU Declaration of Conformity is available at the Product Page on Internet

DISPOSAL

At the end of its lifespan, this product must not be disposed of in household waste. Look for an electronic equipment collection or recycling center for proper disposal

Safety requirements

To ensure proper use, please read through this manual before using the processor. It is specially important that you know the CAUTIONS contained here

• The installation of this product must be done by a qualified professional.
• Use the correct tools for installing this product.
• This product is for use with 12V batteries. Always check the voltage before installing.
• Never install the product in places exposed to dust, humidity and water. Pay attention to install it far from fuel tank, fuel lines, heat sources and other parts of vehicle.
• Be sure to install protection fuse or a circuit braker near to battery. Follow the ampere rating as indicated here in this manual.
• Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through car’s body.
• Automotive sound systems may produce high sound pressure levels. Avoid continuous exposure to levels over 85dB to prevent permanent hearing loss.

Key recommendations

The wire gauge for power supply connections is 1,5mm² (15 AWG) for positive and negative wires, and 0,50mm² (20 AWG) for remote signal wire.
For protection against overload, install a fuse on positive wire, close to battery terminal (1A). See page 06.

1. Power supply negative: Connect to negative pole of battery.
2. Remote signal input: Connect to remote signal output from head unit.
3. Powe supply positive: Connect to positive pole (12V) of battery.

Safety

As you read this manual, pay attention to the safety symbols.

CAUTION
This symbol with “CAUTION” is intended to alert the user to the presence of important instructions. Failure to heed the instructions will result in risk of injury to user or product damage.

Taramps reserves the right to modify the contents of this document at any time without prior notice and does not have the obligation to apply the changes in units which were previously produced.

Crossover overview

1. Signal input (mono) for bass / subwoofer (LOW) way
2. Signal input (mono) for LOW MID way
3. Signal input (L channel) for mid-treble (HIGH MID) and high (HIGH) way 4 Signal input (R channel) for mid-treble (HIGH MID) and treble (HIGH) way 5 Power connector
4. Signal output (mono) of bass / subwoofer (LOW) way
5. Signal output (mono) of LOW MID way
6. Signal outputs (L and R) of HIGH MID way
7. Signal outputs (L and R) of HIGH way
8. Ways filters and controls
9. LED indicator ON

Low Way

Low Mid Way

High Mid Way

High Way

Input & output connections

It is mandatory to install a 1A protection fuse closest to the battery.

Technical features

• Number of ways:……………………………………………………………………………………………………4

• Via Low / Low way (Mono)
  Cutting frequency / Variable (LPF)…………………….40Hz ~ 275Hz (-12dB/8ª)

• Bass Boost
  Frequency Central Variable…………………………..20 ~ 65Hz (6dB / Fixed gain)

• Via Low Mid / Low Mid way (Mono)
  Minimum frequency of (cut HPF) / Variable…………25Hz ~ 140Hz (-12dB/8ª)
  Maximum frequency of (cut LPF) / Variable………300Hz ~ 7.5KHz (-12dB/8ª)

• Via High Mid / High Mid way (Stereo)
  Minimum frequency of (cut HPF) / Variable…………200Hz ~ 5KHz (-12dB/8ª)
  Maximum frequency of (cut LPF) / Variable………1.2KHz ~ 12KHz (-12dB/8ª)

• Via High / High way (Stereo)
  Cutting frequency / Variable…………………………550Hz ~ 13.7KHz (-12dB/8ª)

• Harmonic Distortion (THD):…………………………………………………………<0,01% ~1KHz

• Output Impedance:……………………………………………………………………………….27K ohms

• Maximum input level:………………………………………………………………………………..8V RMS

• Maximum output level:……………………………………………………………………………..8V RMS

• Crosstalk:……………………………………………………………………………………………………….>80dB

• Protection:……………………………………………………………………………………Reverse polarity

• Power supply:………………………………………With switched-mode DC-DC converter

• Voltage Range:…………………………………………………………………………………10 ~ 15.5VDC

• Nominal Consumption (12.6V):…………………………………………………………………..0.38A

• Dimensions (WxHxD):………………………..181x 40 x 145mm / 7.13” x 1.57” x 5.71”

• Weight:…………………………………………………………………………………………0,550Kg / 1.21lb

Manufactured by:
TARAMPS ELECTRONICS LTDA
TAX ID: 11.273.485/0001-03
Street: João Silvério, 121 • Res. Manoel Martins
Alfredo Marcondes – SP
Made in Brazil
www.taramps.com.br

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>