JAR SYSTEMS MC-6032-EDU USB-C Charging Cart EDU User Guide

JAR SYSTEMS MC-6032-EDU USB-C Charging Cart EDU

Specifications

• Model: MC-6032-EDU
• Designed in the USA, Made in China
• USB-C Charging Ports
• LED Charging Port Indicator Lights: White (Port Ready), Blue (Device Charging), Green (Charge Level >90%)
• Supports USB-C Emulator Cables

Product Usage Instructions

Quick Start

1. Connect the cart to a power source.
2. Ensure the power switch on the side of the cart is in the ON position.
3. Plug in powered-down devices. Green LEDs indicate a charge level >90% and blue LEDs indicate device charging.
4. Connect devices to the USB-C charging ports on the cart.
5. Disconnect devices with green LEDs first before those with blue LEDs.

Normal Operation

• Connect/disconnect devices at any time.
• Use USB-C emulator cables for charging (not included).
• Ensure proper connection of devices to avoid cable strain and damage.

Troubleshooting
Always start troubleshooting with a simple reboot. Follow these steps for different issues:

• Entire Charging Hub/Shelf Issue: Unplug and plug the power cord. Check LED indications for power draw.
• Single Port or Device Issue: Verify correct cable connections and try different ports. Replace defective cables if needed.
• Remove/Replace USB-C Cables: Securely remove and replace cables as needed.

Adjusting Device Bay Dividers
Follow these steps to adjust device bays based on width:

• 32 Device Pattern: Best for devices up to 1″ wide.
• 24 Device Pattern: Best for devices up to 1.25″ wide.
• 20 Device Pattern: Best for devices up to 1.5″ wide.

Quick Start

1. Connect the cart to a power source
2. Plug-in powered-down devices
3. Connected devices will automatically charge as efficiently as possible
4. Connect/disconnect devices at any time

LED Charging Port Indicator Lights

Normal Operation

• Plug the power cable into a standard 15A outlet. Be sure that the power switch on the side of the cart is in the ON position. LEDs will illuminate white to indicate the cart is connected to a power source.

• Power off devices fully before connecting them to the cart for charging.

• Connect the devices to the USB-C charging cables. Ensure that devices are placed in the cart so that the charging ports are as close as possible to the USB-C charging port on the cart. Incorrectly connecting devices can strain the cable over long periods and lead to damage.

• You may hear a click. The LED lights will change colour according to the power draw of the attached devices. Refer to the device for the level of charge.

• When devices are not connected, make sure the cables are inside of the lip on the front of the shelf to prevent them from being caught in the door.

• To remove devices from the carts with the greatest level of charge, disconnect devices with the green LEDs first before you disconnect devices with the blue LEDs.

• Devices that do not feature a USB-C charging port can be charged using USB-C emulator cables. (Not Included, contact JAR Systems for more info)

USB-C Emulator Cables

Trouble-Shooting

Always start troubleshooting with a simple reboot
Unplug and replug the power cord. When the cart is connected to power, the LEDs will change color based on the power draw of connected devices (see light indication).

Single Port or Device Issue

• Ensure that both of the cable ends plug into the cart and the device correctly.
• If there is still no charge, disconnect the device from that port (A) and plug into another port (B). If it is still not charging, it may be an issue with the device.
• If charging begins when using port (B), exchange the cable from port (B) to port (A). If it begins to charge, the cable (A) is defective and will need to be replaced.

Entire Charging Hub/Shelf Issue

• Check the back of the charging hub to see if the cart’s power cable is plugged in and connected correctly.
• The easiest way to access the AC power cable is to remove the (right) back panel of the cart.
• When the cart is powered back on, the LED lights will begin to illuminate.

Remove/Replace USB-C Cables

• Each shelf may be secured with up to three screws. Remove all screws.
• Open the tray lid. Unplug the cables from the USB-C ports and route them through the cable track.
• Reverse the process to replace a cable.

Adjusting Device Bay Dividers

Elevate carts feature adjustable device bays with multiple configuration options. Use the guides below to determine which hole pattern to use.

To remove dividers, pull the taller, back part of the divider toward you and lift it upward out of the slot. Then, guide the front part of the divider out of the tray. To install the dividers, place the shorter side of the divider into the front slot first, then pull the taller, back part toward you and downward into the rear slot.

Warnings

• Power down all devices before connecting them to the hub for charging.
• Keep away from moisture and harsh chemicals. Do not place any liquids near the charging cart.
• Any electrical equipment must be used by an adult or with adult supervision.
• Do not connect unsupported items to the charging cart or use them for any purpose other than their intended use.
• Do not attempt to obstruct any ventilation openings or dismantle, open, or modify the system in any way.
• Do not sit or stand on the cart or charging hubs.
• Do not use an extension cable or daisy chain for any other devices.
• Not intended for operation at altitudes greater than 2000 m or 6561 ft above sea level and should not be operated in extreme temperatures. For indoor use only.

Disclaimer
Failure to read, thoroughly understand, and follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty. Since the use of this information, the equipment connected, and the conditions by which any JAR Systems product is used is beyond the control of JAR Systems, it is the obligation of the owner and/or user to determine the correct and safe use of any equipment and product. To the extent that the law permits, any liability which may be incurred as a result of the use or future use of a product manufactured or sold by JAR Systems is limited to the cost of repairing or replacing the failed product or component at the discretion of JAR Systems either within, or outside of warranty periods, and does not extend to any loss or damage which may be caused as a consequence of misuse or failure of the equipment, product or the information contained herein. JAR Systems shall not in any event be liable for economic loss of profits, indirect, special, bodily injuries or consequential damages. Specifications and images are for illustration purposes only. The final product may differ and is subject to change without notice.

Warranty

This product comes with a warranty that covers any defects in material or workmanship and extends to the original consumer of the product only. JAR Systems, LLC will replace the product with a new or refurbished product, repair the product, send replacement parts, or refund the purchase price of the product, at JAR Systems, LLC’s discretion. This warranty does not cover accidental damage, unreasonable use, neglect, tampering or other causes not arising from defects in material or workmanship.

Any implied warranties last only as long as the warranty periods listed above except where state law does not allow limitations on how long an implied warranty lasts. This includes but is not limited to the implied warranties or merchantability and fitness. JAR Systems, LLC’s responsibility is limited to the actions listed above and nothing else.

This warranty does not cover, and JAR Systems, LLC will not be responsible for, any damages due to loss of use of the product, or any other costs or expenses incurred by you or anyone else who uses the product, whether due to defects, breach of contract, negligence, strict liability or otherwise. JAR Systems is not liable for any indirect, special, incidental or consequential damages related to the product or this warranty. Some states do not allow exclusions or limitations on consequential or incidental damages, so these limitations or exclusions may not apply.

This warranty gives you specific legal rights and you may also have other rights that vary from state to state. This warranty is governed by the laws of Florida, excluding its conflict of laws principles, unless your state requires that its law be used.
Contact JAR Systems for information on the length of warranty on your product(s).

Explore more options for USB-C Charging!
Learn about ways to charge devices in growing technology landscapes. Contact a JAR Systems representative at 866.393.4202 or visit:
JAR-Systems.com/Products

FAQ

• What should I do if my device is not charging?
  • If your device is not charging, ensure correct cable connections, try different ports, and replace defective cables if necessary. Always check LED indicators for power status.
• How can I access the AC power cable of the cart?
  • To access the AC power cable, remove the right back panel of the cart. The LED lights will illuminate once powered back on.
• Can I use USB-C emulator cables for charging?
  • Yes, you can use USB-C emulator cables for charging, but ensure correct connections to avoid damage.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>