TARAMPS CRX-5 Plus Electronic 5 Way Crossover Instruction Manual

TARAMPS CRX-5 Plus Electronic 5 Way Crossover Instruction Manual

The installation of this product must be made by a qualified professional.

Term of warranty

TARAMPS, located on Abilio Daguano Street 274, Res. Manoel Martins – Alfredo Marcondes, SP – Brazil, ZIP CODE 19180-000, guarantees this product against any defects on terms of project, making, assembling, and/or with solidarity, due to project vices which cause it improper or inadequate to its original use within 12 months from the date of purchase. In case of defect during the warranty period, TARAMPS responsibility is limited to the repairing or substitution of the device of its own making.

This warranty excludes:

• Damaged products by improper installation, water infiltration, violation by unauthorized individuals;
• Tamper or torn warranty seal;
• Cases in which the product is not used in adequate conditions;
• Defects caused by accessories, modifications or features attached to the product;
• The product with damage from falling, bumps or nature related problems (flooding, lightning, etc.);
• Warranty card is not properly filled or torn;
• Costs involving uninstallation, reinstallation of equipment as well as shipment to the factory;
• Damage of any kind, due to problems in the product, as well as losses caused by discontinued use of the product.

Technical assistance

For international support, check on our website: www.taramps.com.br/en/rede- de-assistencias-tecnicas or contact direct the factory support: Phones: +55 18 3266-4050 / +55 18 99749-3391
E-mail: service@taramps.com.br

Introduction

Read this manual before installing the product. In case of questions contact our technical support: +55 (18) 3266-4050 or www.taramps.com.br.

At the end of its lifespan, this product must not be disposed of in household waste. Look for an electronic equipment collection or recycling center for proper disposal.

Safety requirements

To ensure proper use, please read through this manual before using the processor. It is specially important that you know the CAUTIONS contained here.

• The installation of this product must be done by a qualified professional.
• Use the correct tools for installing this product.
• This product is for use with 12V batteries. Always check the voltage before installing.
• Never install the product in places exposed to dust, humidity and water. Pay attention to install it far from fuel tank, fuel lines, heat sources and other parts of vehicle.
• Be sure to install protection fuse or a circuit braker near to battery. Follow the ampere rating as indicated here in this manual.
• Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through car’s body.
• Automotive sound systems may produce high sound pressure levels. Avoid continuous exposure to levels over 85dB to prevent permanent hearing loss.

Key recommendations

The wire gauge for power supply connections is 1,5mm² (15 AWG) for positive and negative wires, and 0,50mm² (20 AWG) for remote signal wire.
For protection against overload, install a fuse on positive wire, close to battery terminal (1A).

1. ➖Power supply negative: Connect to negative pole of battery.
2. Remote signal input: Connect to remote signal output from head unit.
3. ➕Powe supply positive: Connect to positive pole (12V) of battery.

Safety

As you read this manual, pay attention to the safety symbols.

CAUTION This symbol with “ CAUTION ” is intended to alert the user to the presence of important instructions. Failure to heed the instructions will result in risk of injury to user or product damage.

Taramps reserves the right to modify the contents of this document at any time without prior notice and does not have the obligation to apply the changes in units which were previously produced.

Crossover overview

1. Signal output (R + L)

2. Signal inputs sent directly from a CD / DVD Player

3. Signal inputs (SUB) sent directly from a CD / DVD Player (Optional)

4. Signal output, bass / subwoofer (LOW) (R + L)

5. Signal output, LOW MID (R + L)

6. Way signal output HIGH MID (R and L)

7. Way signal output HIGH (R and L)

8. LOW input selector switch

9. PHASE- Phase Inverter: Inverts phase
   0/180 of each route
   MUTE – Enable / Disable the audio of each track

10. Subsonic filter

11. Way filter controls

12. LED indicator

13. Power connector

PASS THRU

LOW WAY

LOW MID WAY

HIGH MID WAY

HIGH WAY

Input & output connections

Technical features

Number of ways:……………………………………………………………………………..4 + 1 Pass Thru

Via Pass Thru (R+L)
Selectable phase:…………………………………………………………………………….0/180 degrees

Variable level………………………………………………………………………………….-infinite ~ +6dB

Via Low (R+L) Mono
Subsonic Filter:………..Selectable (Bypass/40/60/80Hz) (-24dB/8ª butterworth)
Low Pass Filter:……………………..Variable 100Hz ~ 2KHz (-12dB/8ª Linkwitz-Riley)
Bass Boost:…………………………………………………………………..Variable 0 ~ +10 dB (40Hz)
Selectable Phase::…………………………………………………………………………….0/180 degrees
Selectable Phase:………………………………………………………………………..-infinite ~ +10dB

Via Low Mid (R+L) Mono
High Pass Filter:…………………….Variable 30Hz ~ 600Hz (-12dB/8ª Linkwitz-Riley)
Low Pass Filter:……………………Variable 600Hz ~ 10KHz (-12dB/8ª Linkwitz-Riley)
Fase Selectable:………………………………………………………………………………..0/180 degrees
Variable level………………………………………………………………………………-infinite ~ +10dB

Via High Mid (R e L) Stereo
High Pass Filter:…………………..Variable 400Hz ~ 3KHz (-12dB/8ª Linkwitz-Riley)
Low Pass Filter:……………………..Variable 5KHz ~ 20KHz (-12dB/8ª Linkwitz-Riley)
Selectable Phase:……………………………………………………………………………..0/180 degrees
Variable level………………………………………………………………………………-infinite ~ +10dB

Via High (R e L) Stereo
High Pass Filter:…………………….Variable 2KHz ~ 10KHz (-12dB/8ª Linkwitz-Riley)
Selectable Phase:………………………………………………………………………………0/180degrees
Variable level………………………………………………………………………………-infinite ~ +10dB

Harmonic Distortion (THD):………………………………………………………….<0,01% ~1KHz

Input Impedance:…………………………………………………………………………………….10K ohms
Output Impedance:………………………………………………………………………………470K ohms
Maximum input level R/L:…………………………………………..4,57 V RMS @ (+15,4 dBu)
Maximum output level R/L:…………………………………………..9,3 V RMS @ (+21,6 dBu)
Maximum output level Pass Thru R/L:…………………………9,3 V RMS @ (+21,6 dBu)
Crosstalk:……………………………………………………………………………………………………………85dB
Frequency Response:………………………………………………………….(-1dB) 10Hz ~100KHz
Protection:……………………………………………………………………………………..Reverse polarity

Voltage Range:…………………………………………………………………………………..10,5 ~ 16VDC
Nominal Consumption (12.6V):………………………………………………420mA @ 12,6 Vcc
Dimensions (WxHxD):…………………………238 x 40 x 145mm / 9.37” x 1.57” x 5.71”
Weight:……………………………………………………………………………………………..0,70Kg / 1.54lb

+55183266-4050

Manufactured by:
TARAMPS ELECTRONICS LTDA
CNPJ / TAX ID: 11.273.485/0001-03
Street: João Silvério, 121 • Res. Manoel Martins Alfredo Marcondes – SP
Made in Brazil
www,taramps.com.br

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>