Tindie HU-064 High Voltage Electromagnetic Transmitter DIY Kit User Guide

June 15, 2024
tindie

Tindie HU-064 High Voltage Electromagnetic Transmitter DIY Kit

Specifications

  • Work Voltage: DC 3V
  • Charging Current: 50~60mA
  • Discharging Current: 70~80mA
  • Power Type: AA*2 Battery (Not Included!)
  • Work Temperature: -20~85
  • Work Humidity: 5%~85%RH
  • Size (Installed): 948784mm

Product Usage Instructions

Charging the Transmitter

  1. Turn ON the black power switch to charge the capacitor.
  2. Wait for approximately 10-30 seconds until the blue/red LED indicator slowly brightens up.

Launching the Metal Cylinder:

  1. Insert the metal cylinder into the plastic tube, ensuring its tail is flush with the tube’s end.
  2. Press the launch button (red button) to release the metal cylinder.

Safety Precautions

  • Avoid touching metal parts when the device is charged as it operates under high voltage.
  • Always discharge the energy storage capacitor before troubleshooting. Refer to the user manual for instructions.
  • Children under 14 should use the kit under adult supervision.

Recharging and Relaunching
The transmitter can be launched once each time. Recharge after launching and relax after pressing the launch button.

Frequently Asked Questions (FAQ)

  • Q: Can children use this kit without adult supervision?
    A: No, children under the age of 14 should be supervised by an adult when using the HU-064 High Voltage Electromagnetic Transmitter DIY Kit.

  • Q: How long does it take to charge the capacitor?
    A: It takes approximately 10-30 seconds to complete charging, indicated by the brightening of the blue/red LED.

  • Q: What type of battery does this kit use?
    A: The kit uses AA*2 batteries (not included) as a power source.

HU-064 High Voltage Electromagnetic Transmitter DIY Kit

Introduction

HU-064 is a DC 3V High Voltage Electromagnetic Transmitter DIY Kit. It can simulate an electromagnetic transmitter and convert electrical energy into magnetic energy, thereby injecting a metal cylinder. Users can use it to learn and understand the working principle of electromagnetic transmitters and learn the basics of electronic technology.
It is a very interesting DIY electronic product which enables users to understand the circuit more clearly and learn soldering skills.

Feature

  1. Instructions & Steps for Usage:1>Turn ON black power switch to charge the capacitor; 2>.Wait for approximately 10-30 seconds to complete charging and the blue/red LED is charge indicator and slowly brighten up; 3>.Insert the metal cylinder from the rear end of the plastic tube, and its tail should be flush with the tail of the tube; 3>.Press the launch button (red button), the metal cylinder will fly out, and the launch is complete.

  2. DIY Hand Soldering: It’s a DIY kit which comes with various components. User need to install each component by hand. It not only can exercise and improve soldering skills, but also increase the interest in electronic technology. Great for electronics hobbyists, beginners, school and home education.

  3. Easy to Assemble: During the assembly process, the kit requires not all soldering, and more needs to connect the circuit and assemble the components. We have prepared a detailed user manual for you. The connection that was clearly mapped and labeled on the board, easy to build and the principle is simple. But still requires certain foundation of basic electronic theoretical knowledge and welding and hands-on ability.

  4. Please Pay Attention: 1>.Do not touch the metal parts with your hands when it is charged. The finished project is a device that works under high voltage. 2>.Please discharge the energy storage capacitor before troubleshooting. Please refer to user the manual for detailed discharge operation.
    3>.Children under the age of 14 need to be installed and used it under the supervision of an adult.

  5. Warm Tips : 1>. It can be launched once each time, and after the launch is completed, it needs to be recharged. 2> Relax as soon as possible after pressing the launch/red button.

Parameter

  1. Work Voltage: DC 3V
  2. Charging Current: 50~60mA
  3. Discharging Current: 70~80mA
  4. Power Type:AA*2 Battery(Not Included!)
  5. Work Temperature:-20℃~85℃
  6. Work Humidity:5%~85%RH
  7. Size(Installed):948784mm

Use Steps

  1. Complete the installation correctly according to the installation manual.
  2. Turn ON black KCD-11 power switch then the green power indicator will turn ON.
  3. Automatically start to charge the capacitor after power ON and the blue and red LED is charge indicator and slowly brighten up.
  4. It means that the capacitor charging has reached 50% when the blue indicator turn ON completely. Charging time is approximately 10-30 seconds.
  5. It means that the capacitor charging has reached 100% when the red indicator turn ON.
  6. Insert the cylindrical metal rod from the rear end of the plastic tube, and its tail should be flush with the tail of the tube.
  7. Press red DS-316 momentary launch switch between 50% to 100% to cylindrical metal rod that will fly out, and the launch is complete. 50% can be launched, no need to wait for 100%.

Notes

  1. The instantaneous voltage inside the circuit board reaches about 210V, so please don’t touch component during charging.
  2. Do not wear or damage the insulation layer on the surface of the wire.
  3. The capacitor must be discharged first before circuit testing. The capacitor has been discharged if the blue indicator turn OFF.
  4. Its power consumption is relatively fast, the working voltage is about 50mA when charging, so it is recommended to use a new battery.
  5. Its working voltage is 3V, so the input voltage must not exceed the working voltage.
  6. It can be launched once each time, and after the launch is completed, it needs to be recharged.
  7. The launch distance is related to the horizontal position, Iron Pillar’s position and many other factors.
  8. Before stopping use, it is recommended to fire several times to release the electric energy inside the capacitor.

Component Listing:

NO. Component Name PCB Marker Parameter QTY
1 Metal Film Resistor R5 1Kohm 1
2 Metal Film Resistor R1,R6 5.1Kohm 2
3 Metal Film Resistor R2,R3 10Kohm 2
4 Metal Film Resistor R4 470Kohm 1
5 1N4148 Diode D1 DO-35 1
6 2EZ91D5 Zener Diode D2 DO-41 1
7 S9013 Transistor Q1,Q2 TO-92 2
8 5mm Green LED LED1 Green 1
9 5mm Blue LED LED2 Blue 1
10 5mm Red LED LED3 Red 1
11 KCD-11 Switch K1 2Pin 1
12 Electrolytic Capacitor C1 1000uF 1
13 DS-316 Momentary Switch K2 Red 1
14 Magnetic Induction Coil U1 6Pin 1
15 Electromagnetic Coil L4 12Pin 1
16 Metal Cylinder 4*12mm 5
17 Red/Black Wire 120mm 3
18 AA*2 Battery Box BAT1 1
19 Transparent Plastic Pipe M10*70mm 1
20 Double-Sided Tape 1
21 Acrylic Board 6
22 White Isolation Column M3*6mm 4
23 M3*10+6mm Copper Column 4
24 M3*12mm Screw 4
25 M3*5mm Screw 4
26 M2*10mm Screw 4
27 M3 Nut 4
28 M2 Nut 4
29 Metal Cap 4
30 PCB Circuit Board 85*78mm 1
31 PCB Circuit Board 53*50mm 1

NOTE:Users can complete the installation according to the PCB silk screen and component list.

Schematic Diagram:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals