ATOMSTACK A5 10W Air Assist Kit Laser Engraver Air Assist User Manual

ATOMSTACK A5 10W Air Assist Kit Laser Engraver Air Assist

Product Information

• Specifications:
  • Pump
  • Power Adapter
  • Trachea
  • M3 self-tapping screws
  • Set screw
  • Inner hexagon screwdriver
  • PH1 Phillips screwdriver
  • Footpad 2pcs
  • NO. 1 2pcs
  • NO. 1-1
  • NO. 1-2
  • NO. 1-3
  • NO. 2
  • NO. 2-1

Product Usage Instructions

• Installation of Air Guide Hood for Various Models:
  • Atomstack A5 10W, Atomstack A5 30W:
  • Remove the current acrylic shields.
  • The air guide hood tube mouth is on the left.
  • Remove the set screw.
  • Rotate the current air guide hood counterclockwise to remove it.
  • Find NO.1 from the accessories and install it.
  • Tighten the self-tapping screws with a PH1 Phillips screwdriver.
  • Find NO.1-1 from the accessories and install it.
  • Insert the tube and fix it with a tie.
  • Equipment Installation and Use:
  • Tear off the adhesive protect paper from the silicone pad, align the positioning posts on the silicone pad with the mounting holes on the pump, and paste the silicone pad to the pump body.
  • Insert the air tube into the air pump port.
  • The tube on the machine needs to be fixed with the connecting line by the nylon tie. Be careful not to fix it too tight to block the tube.
  • Precautions for Use:
  • Be careful not to get the tube stuck by the wheels.
  • Avoid bending the tube too much to prevent blockage.
  • Clean the adhesions on the air outlet after using the air guide hood to prevent accumulation over time.

FAQs

• Q: How do I choose the correct combination for AtomStack A5 Pro+ or AtomStack P7 M40 models?
  • A: If the bottom surface of the glass and the laser are flush after assembly, choose the combination that matches your model. Ensure proper alignment before installation.

Parts List

This is a parts collection for various models, not each model will use all parts in the sheet.

Installation

Installation of Air Guide Hood for Four Models

1. Remove the current acrylic shields
2. Rotate the laser backward 180°
3. Remove the set screw
4. Rotate the current air guide hood counterclockwise to remove it.
5. Find NO.1 from the accessories. Install it as shown
6. Tighten the self-tapping screws with a PH1 Phillips screwdriver
7. Find NO.1-1 from the accessories and install it as shown.
8. Insert the tube and fix it with a tie

Installation of Air Guide Hood for Eight Models

Atomstack A5 M50 Pro| AtomStack P9 M40| Atomstack X7 Pro| AtomStack P9 M50
---|---|---|---
AtomStack A10 PRO| Atomstack A5 M50| Atomstack S10 Pro| Atomstack X7

1. Remove the set screw from the right side of the laser and remove the current filter glass or acrylic shield.
2. Remove the current air guide hood.
3. Find NO.1 and NO.1-2 from the accessories and install them at the same time as shown.
4. Fix the air guide hood as well as the filter glass.
5. Insert the tube.

If your model is AtomStack A5 Pro+ or AtomStack P7 M40, you need to choose one of the following 2 combinations to support your model.

Equipment installation and use

1. Tear off the adhesive protect paper from the silicone pad, align the positioning posts on the silicone pad with the mounting holes on the pump, and paste the silicone pad to the pump body.
2. Insert the air tube into the air pump port
3. The tube on the machine needs to be fixed with the connecting line by the nylon tie. Be careful not to fix it too tight to block the tube.

Precautions for Use

• Be careful not to get the tube stucked by the wheels.
• Please do not bend the tube too much to make the tube blocked.
• Please note the tube cannot be bent too much to make the tube blocked.

CONTACT

Customer Service:

• For a detailed warranty policy, please visit our official website at: www.atomstack.net.
• For technical support and service, please email  support@atomstack.net.

Scan the code to enter the discussion group.

• Scanner APPLICATION: QR code reader/ Barcode scanner or any APP with the scanner.
• Manufacturer: Shenzhen AtomStack Technologies Co., Ltd.
• Address: 202, Building 1, Mingliang Technology Park, No. 88 Zhuguang North Road, Taoyuan Street, Nanshan District, Shenzhen, Guangdong, China
• Scanner APPLICATION: QR code reader/ Barcode scanner or any APP with the scanner.
• Note: The picture is for reference only, the actual product shall prevail.
• F03-0046-0AA1 Version: C
• For more information, please scan the QR code

References

• Atomstack Official Store - Laser Engraving Machine

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>