marco MIX / POUR’D Cold Coffee Dispenser Instruction Manual
- June 3, 2024
- marco
Table of Contents
marco MIX / POUR’D Cold Coffee Dispenser
Font Box Contents
3 & 1 Button Models
- 3 /1 button MIX Font 1000879 / 1000878
- Vent Hosing 1860388
- 8mm Water Hose 1860387
- 1/4” Water Hose 1860387
- Instruction Manual
- Vent plug 1401482
- 8mm-1/4” reducer 1400820
3B Concentrate 1000942
- 3B POUR’D concentrate Font
- 8mm Water Hose 2301250
- 1/4” Water Hose 2301251
- Vent Hosing 1860630
- Instruction Manual
Counter Cut Out
- The 100mm /4” cut-out is only required for the font with drip tray.
- The font without drip tray requires the 32mm / 1 ¼” cut out only.
- Use a 32mm/ 1 ¼” & a 100mm /4” circular hole saw piece to make the holes.
Installation
- No Drip Tray
- Drip Tray (sold separately p/n. 2300268)
Connecting Hoses
MIX 3 Button Font Connections
MIX programmable buttons
Operating Font
- Push & Hold
- Push & Release
HOT/AMBIENT WATER, DILUTED CONCENTRATE & CONCENTRATE SHOT
3 button connections (1000942 3b concentrate)
For use with a Boiler
Control box setup
| MODE | DESCRIPTION |
|---|---|
| HOT | Hot Water (set ratio to 0% ) |
| COLD | Cold/ambient water mixed with concentrate (set ratio |
to 0% for just cold water)
RTD| Ready-to-drink, undiluted concentrate
OFF| Button non-active
PRI| Triggers second control box, in case of 2 control boxes
primary must be one connected to the font
% Concentrate| Water to Coffee ratio
20%| 4:1
10%| 9:1
Boiler setup
CHILLED WATER, DILUTED CONCENTRATE & CONCENTRATE SHOT
3 button connections (1000942 3b concentrate).
For use with chiller
Control box setup
| MODE | DESCRIPTION |
|---|---|
| HOT | Hot Water (set ratio to 0% ) |
| COLD | Cold/ambient water mixed with concentrate (set ratio |
to 0% for just cold water)
RTD| Ready-to-drink, undiluted concentrate
OFF| Button non-active
PRI| Triggers second control box, in case of 2 control boxes primary must be
one connected to the font
User Setup
- Programmable buttons
- Program and change buttons accordingly
| OPTION | DESCRIPTION |
|---|---|
| Calibrate conc pump | Will pump concentrate using FAST speed for 10 seconds and |
ask for weight to be entered – then again the same at SLOW speed. (for
accurate results make sure system is primed / tubes are full with liquid)
Calibrate Cold water| Will dispense water until flowmeter clicks 200 pulses
and then will ask to enter weight. (for accurate results make sure system is
primed / tubes are full with liquid)
Calibrate Hot water| will dispense hot water from the boiler for 10 seconds
and ask for weight to be entered.
RTD speed| This is the speed of the pump (in % of full speed) If flow rate is
too violent this should be reduced
Chiller present| Select yes if you are using a chiller to supply cold water
Operating Font
- Push & Hold
- Push & Release
Cleaning & Maintenance
RISK OF SCALDING
Turn off the boiler before cleaning to prevent accidental triggering of a
dispense. Beware of accidentally operating the font – especially when cleaning
around the push buttons. The appliance may not be immersed in water or a
cleaning solution. The exterior of this font may be cleaned with a damp cloth
and a light detergent. The external surfaces of the appliance must not be
cleaned by a water jet.
For cleaning the internal tubing and components, the recommended cleaning solution is Urnex Cafiza cleaner. Twist off and wash out the flow straightener. Do not use abrasive cloths or creams, as this will.
Marco Beverage Systems Limited.
- 63d Heather Road, Sandyford Industrial Estate, Dublin 18
- t: +353 (0)1 295 2674
- f: +353 (0)1 295 3715
- e: sales@marco.ie.
- Web: www.marcobeveragesystems.com.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>