TELOX TE320A PoC Smart Radio User Guide

: June 12, 2024
: TELOX

Table of Contents

TELOX TE320A PoC Smart Radio
Product Usage Instructions
FAQ
Indicators
Description
Check List
Before Use
Charging
Caution
FCC Statement
CE Warning
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

TELOX TE320A PoC Smart Radio

Product Usage Instructions

Before Use:

Insert the SIM card or TF card into the designated slot.
Place the battery in the compartment, close the cover, and lock it.

Charging:
Connect the LTE handheld device to a power adapter using the USB data cable. The red light indicates that the battery is charging, while the green light signals a fully charged battery.

Care and Maintenance:

Avoid dropping, hitting, bending, or sitting on the device.
Ensure charger/USB port covers are properly sealed with no obstructions.
Do not use the charger/USB port until the device is completely dry.
Avoid storing the device in erosive environments.
Clean the device with a dry, lint-free cloth or hairbrush; do not use chemicals.
Dry the device completely after cleaning before use.

FAQ

Q: What should I do if I encounter missing or damaged parts upon unboxing?

A: Please contact your local dealer immediately to address any missing or damaged parts.

Q: How can I ensure proper charging of the device?

A: Always use Telox Original batteries and chargers for optimal performance and to maintain warranty coverage.

Q: How should I clean the device?

A: Use a dry and clean lint-free cloth or a hairbrush to clean the device and charger docking port. Avoid using any chemical agents for cleaning.

Thanks for choosing our product!
This Quick Start Guide is only applicable to: TE320A. Before using the product, please read the Quick Start Guide to fully benefit from it.

Indicators

Operating State

|

Indication

---|---
Low Battery| Red(Blinking)
Charging| Red(Steady)
Fully Charged| Green(Steady)
PTT Transmitting| Red(Steady)
PTT Receiving| Green(Steady)

Description

Note

The warranty period for the TE320A is 2 years from the date of purchase.
This product involves constant upgrading and/or improvement, our company reserves the right to change the specifications of software and/or hardware mentioned in this operating guide without any prior notice. The product specifications and information mentioned in the operating guide are for reference only.

Check List

Notice:
Please check the above accessories before you discard the packing material. Please contact your local dealer immediately if there are any missing or damaged parts.

Before Use

Insert the SIM/TF card into its slot. SIM cards can be inserted in SIM 1 or SIM 2, or two cards for both.
Put the battery into the compartment, then put on the cover and lock.
Press and hold the power button until the screen lights up to turn on the device. Press the power button to put the device screen to sleep, and press again to wake it up.

Charging

Connect the LTE handheld and power adapter using the USB Data Cable.
The red light on the LTE handheld indicates battery charging is in progress.
Green lights on indicate fully charged.

Notice:
Always use Telox Original batteries and chargers. The warranty does not cover damage caused by non-Telox batteries and/or chargers.

Caution

Although your device is quite sturdy, it is a complex piece of equipment and can be broken. Avoid dropping, hitting bending, or sitting on it.
Make sure the charger/USB port, and microSD card/SIM card slot covers are properly seated, with no foreign objects obstructing the seals.
Do not use the charger/USB port for charging, data transmission, etc. until the phone is completely dry.
Do not store the device under any circumstance containing electronic erosive material.
Avoid pulling the device up by holding the antenna or accessories.
Please power off and unload the battery before cleaning the device.
Use a dry and clean lint-free cloth or hairbrush to keep the device and charger docking port clean.
Avoid using any chemical agent including detergent, alcohol, aerosol spray or oil preparations as a cleaning solution.
Dry your device completely after cleaning and before using it again.

FCC Statement

Labelling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Information to the user.
Any changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Information to the user.
This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit diﬀerent from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Speciﬁc Absorption Rate (SAR) information:
This product meets the government’s requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientiﬁc studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health.

FCC RF Exposure Information and Statement
The SAR limit of USA (FCC) is 1.6 W/kg averaging over one gram of tissue. This device was tested for typical body-worn operations when the device was used at 25mm from the front face and 10mm from the product, 0mm from the belt, to maintain compliance with FCC RF exposure requirements. The use of belt clips, holsters and similar accessories should not contain metallic components in their assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements and should be avoided.

CE Warning

Use carefully with the earphones maybe excessive sound pressure from earphones and headphones can cause hearing loss.
Risk of explosion if the battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
The product shall only be connected to a USB interface of version USB2.0 or higher.
The adapter shall be installed near the equipment and shall be easily accessible.
EUT Operating temperature range: -20° C to 50° C.
Adapter: The plug is considered as the disconnect device of the adapter Power supply and ADP (rating):
- Input: AC 100-240V, 50/60Hz 0.3A
- Output: DC 5V 2A
The device complies with RF speciﬁcations when the device is used at 5mm from the body without belt clips, 0mm from the body with the belt clips, and 25mm from the face.
To prevent possible hearing damage. Do not listen at high volume levels for long periods.

Hereby, Telo Communication (Shenzhen) Co., Ltd declares that this Mobile phone product complies with essential requirements and other relevant provisions of Directive 2014/53/EU. This product is allowed to be used in all EU member states.

Telo Communication (Shenzhen) Co., Ltd