Apulsetech RFID MINI Turns Smartphone into Powerful RFID Reade User Manual

Apulsetech RFID MINI Turns Smartphone into Powerful RFID Reade

Product Information

RFID Mini

The RFID Mini is a compact RFID reader designed for various applications requiring RFID technology. It features a custom module with an embedded Impinj R2000 RFID engine, supporting EPC Class1 GEN 2 and ISO 18000-6C protocols. The reader operates within different frequency ranges depending on the region, with a supply voltage of 5V DC and a maximum RF power output of 20dBm.

Specifications

• Air Interface Protocol: EPC Cass1 GEN 2 / ISO 18000-6C
• RFID Engine: Custom module with embedded Impinj R2000
• Frequency Range: FCC: 902~928MHz, CE: 865~868MHz, Japan: (specific frequency range)
• Supply Voltage: 5V DC
• RF Power Range: Max 20dBm
• Reading Performance: Up to 1m (depending on the tag & environment)
• Writing Performance: Up to 10cm (depending on the tag & environment)
• Operating Temperature: 0 ~ 50°C
• Storage Temperature: -20 ~ 70°C
• Storage Humidity: 20% ~ 95% (Relative Humidity)
• Average Current Consumption: Scan Mode: 500mA @20dBm
• Special Function: Anti-Collision

Product Usage Instructions

RFID Mini Application

1. Connect the USB cable to the USB terminal of the PC.
2. Run the demo program on your PC to test its operation.

RFID Reader Manual

1. Running the RFID Program: Double-click SampleModuleWinForm.exe in the DemoModuleWinForm folder to run it. Folder: DemoModuleWinForm -> Release -> net461
2. Connect by Serial:
3. Enter the number of antenna ports of the terminal.
4. Set Com. Port and Baud rate.
5. Inventory:
   • Click the Icon to run.
   • Click Icon to start inventory.
   • Click Icon to stop inventory.

Frequently Asked Questions (FAQ)

• Q: What should I do if the RFID Mini reader is not being detected by my PC?
  • A: Make sure that the USB cable is securely connected to both the reader and the PC. You may also need to check if the drivers are properly installed on your PC.
• Q: Can I use the RFID Mini reader with tags from different manufacturers?
  • A: Yes, the RFID Mini reader is compatible with tags from various manufacturers as long as they adhere to the supported protocols and frequencies.

Dimension

Drawing (unit : mm)

RFID Specifications

RFID Mini Application

• Connect the USB cable to the USB terminal of the PC.
• Run the demo program on your PC to test its operation

RFID Reader Manual

1. Running the RFID Program Double-click SampleModuleWinForm.exe in the DemoModuleWinForm folder to run it.
   • Folder : DemoModuleWinForm -> Release->net461
2. Connect by Serial
3. Enter the number of antenna ports of the terminal.
4. Set Com. Port and Baud late.
5. Click the Icon to run
6. Inventory

FCC Statement

Certification and Safety Approvals FCC Compliance Statement

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antennae
• Increase the separation between the equipment and the receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

FCC RF Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions to satisfy RF exposure compliance. The antenna used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. When equipped, the distance between the antenna and one’s body surface is 200mm.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>