iArmor IA-N313H Rocker Steps Running Boards Installation Guide

iArmor IA-N313H Rocker Steps Running Boards

INSTALLATION GUIDE

MODEL: IA-N313H

BEFORE INSTALLATION

REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMENDED.

THANK YOU FOR CHOOSING OUR PRODUCT!

• ROCKER PANEL MOUNT
• DRILLING NOT REQUIRED

Torque Value

PART LIST

Note: Step bars are NOT interchangeable.
Make sure drain holes at the bottom will be located at the rear direction of the step bars.

Part List

• Driver Front Mounting Bracket (DFM) – PART#: IA-N313H
• Passenger Front Mounting Bracket (PFM)
• Driver Center Mounting Bracket (DCM)
• Passenger Center Mounting Bracket (PCM)
• Driver Rear Mounting Bracket (DRM)
• Driver Rear Support Bracket (DRS)
• Passenger Rear Support Bracket (PRS)
• Passenger Rear Mounting Bracket (PRM)
• Driver Side Step Bar
• Passenger Side Step Bar

Hardware Package A (For Brackets & Bars Installation)

The instruction here is for your reference only. We strongly recommend the professional installer for best result. We are not responsible for any damage caused by the installation.

STEP 1

Install (4) Pedals onto the step bars with (24) M8X1.25-25mm Hex Bolts, (24) M8 Large Flat Washers and (24) M8 Lock Washers.

IMPORTANT: Don’t punch the pedal with any metal hummer within pedal installation, or the pedal will be damaged.

STEP 2

Start the installation under the passenger side of the vehicle. Locate the front factory mounting location along the inner side of the body panel, (Fig 1).

(Fig 1) Passenger Side Front Mounting Location

STEP 3

Remove the plastic plugs covering the mounting holes. Select Passenger Front Mounting Bracket (PFM), (Fig 2). Attach to Passenger side front mounting location with (2) M10x1.5-25mm Hex Bolts, (2) M10 Lock Washers and (2) M10 Large Flat Washers, (Figs 2 & 3). Do not fully tighten hardware at this time.

(Fig 2) Passenger Front Mounting Bracket Installation

(Fig 3) Passenger Front Mounting Bracket Installed

STEP 4

Locate the Center threaded mounting holes. Select (1) Passen-ger Center Mounting Bracket (PCM). Attach with (2) M10x1.5- 25mm Hex Bolts, (2) M10 Lock Washers and (2) M10 Large Flat Washers, (Figs 4 & 5). Do not fully tighten hardware at this time.

(Fig 4) Passenger Side Center Mounting Location

(Fig 5) Passenger Center Mounting Bracket Installation

STEP 5

Attach the Passenger Rear Support Bracket (PRS) to the Pas-senger Rear Mounting Bracket (PRM) with (1) M8X1.25-30mm Hex Bolt, (2) M8 Large Flat Washers and (1) M8X1.25 Lock Nut, (Fig 6). Do not fully tighten hardware at this time.

(Fig 6) Passenger Rear Brackets Assembly

STEP 6

Repeat Step 4 to install the assembled Passenger Rear Mounting Bracket, (Fig 7). Do not fully tighten hardware at this time.

(Fig 7) Passenger Rear Mounting Bracket Installed

STEP 7

Once all (3) brackets have been installed, select (5) M8X1.25-20mm T-Bolts, thread (1) M8 Plastic Washer on each T-Bolt, (Fig 8). Install the (5) M8X1.25-20mm T-Bolts with plastic washers in the slots on the assembled step bar. Rotate the T-Bolts to 90 degree, thread down the M8 Plastic Washers against the step bar (Fig 9).

NOTE: The Plastic Washer is designed to keep the T-Bolt in place to avoid falling into the tube during installation.

(Fig 8) Thread (1) M8 Plastic Washer on each T-Bolt Before In-serting into the slot !!!

(Fig 9) T-Bolt with plastic washer in the slot

STEP 8

Attach the Assembled Passenger Side Step Bar onto the Mounting Brackets with (5) M8 Plastic Washers, (5) M8X1.25-20mm T-Bolts, (5) M8 Large Flat Washers, (5) M8 Nylon Lock Nuts, (Fig 10). Do not fully tighten hardware at this time.

NOTE: Passenger Rear Mounting Bracket is located under (1) pedal. Slide (1) M6X1-20mm Square Head Bolt into the chan-nel at the bottom of pedal (Fig 11). And secure the Passenger Rear Mounting Bracket to pedal with (1) M6 Large Flat Washer and (1) M6 Nylon Lock Nut, (Fig 10). Do not fully tighten hard- ware at this time.

STEP 9

Level and adjust the assembled Step Bar properly and tighten all hardware.
Move to the other side of the vehicle. Repeat Steps 2-8 for the other Side Step Bar installation.

Attention
Do periodic inspections to the installation to make sure that all hardware is secure and tight.
In order to protect your bars/boards, please use mild soap/non-abrasive products for cleaning only.

Customer Support: info@iarmorauto.com

Specifications

• Product Name: IARMOR EDGETM

• Installation Type: Rocker Panel Mount

• Drilling Requirement: Not Required

FAQ

Q: Is professional installation recommended?

A: Yes, we strongly recommend professional installation for the best results. We are not responsible for any damage caused by improper installation.

Q: Are the step bars interchangeable?

A: No, the step bars are not interchangeable. Ensure correct orientation with drain holes at the bottom facing the rear direction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>