iArmor IA-N171H Pocket Drop Steps Armor Instruction Manual
- June 1, 2024
- iArmor
Table of Contents
iArmor IA-N171H Pocket Drop Steps Armor
Product Information
- Specifications
- Product Name: IARMOR EDGETM
- Part Number: IA-N171H
- Installation Type: Rocker Panel Mount
- Drilling/Trimming: Not Required
Product Usage Instructions
- Step 1: Pedals Installation
- Install (4) Pedals onto the step bars with (24) M8X1.25-25mm Hex Bolts, (24) M8 Large Flat Washers, and (24) M8 Lock Washers.
- Avoid using a metal hammer during pedal installation to prevent damage.
- Step 2: Mounting Brackets Installation
- Start the installation under the passenger side of the vehicle.
- Locate the 6 plugs along the bottom of the body panel and remove the plastic plugs from each mounting location if equipped.
- Mounting Brackets will bolt to the 1st, 3rd, and 6th threaded mounting holes.
- Thread an 8mm Hex Bolt into the threaded inserts to clear paint as required.
- Step 3: Bracket Assembly
- Assemble the Passenger Front Mounting Bracket (PFM) and Passenger Front Support Bracket (PFS) with (1) M8X1.25-30mm Hex Bolt, (2) M8 Large Flat Washers, and (1) M8 Nylon Lock Nut.
- Do not fully tighten at this time.
FAQs
- Q: Is professional installation recommended for this product?
- A: Yes, we strongly recommend professional installation for the best results. We are not responsible for any damage caused by incorrect installation.
- Q: Are the step bars interchangeable?
- A: No, the step bars are not interchangeable. Ensure that drain holes at the bottom are located in the rear direction of the step bars.
- Q: What is the torque value for different fastener sizes?
- A: The tightening torque values in ft-lbs are as follows:
- 6mm: 6-7 ft-lbs
- 8mm: 16-18 ft-lbs
- 10mm: 31-32 ft-lbs
- 12mm: 56-58 ft-lbs
- 14mm: 92-94 ft-lbs
- Q: How can I contact customer support?
- A: For customer support, you can reach out to info@iarmorauto.com.
BEFORE INSTALLATION
- REMOVE CONTENTS FROM THE BOX.
- VERIFY ALL PARTS ARE PRESENT.
- READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
- ASSISTANCE IS RECOMMENDED.
THANK YOU FOR CHOOSING OUR PRODUCT!
- ROCKER PANEL MOUNT
- DRILLING/TRIMMING NOT REQUIRED
Torque Value
| Fastener Size | Tightening Torque (ft-lbs) | Required |
|---|---|---|
| 6mm | 6-7 | √ |
| 8mm | 16-18 | √ |
| 10mm | 31-32 | X |
| 12mm | 56-58 | X |
| 14mm | 92-94 | X |
PART LIST
Hardware Package
The instructions here are for your reference only. We strongly recommend the professional installer for the best result. We are not responsible for any damage caused by the installation.
INSTALLATION STEPS
- STEP 1
- Install (4) Pedals onto the step bars with (24) M8X1.25-25mm Hex Bolts, (24) M8 Large Flat Washers and (24) M8 Lock Washers.
- IMPORTANT: Don’t punch the pedal with any metal hummer within the pedal installation, or the pedal will be damaged.
- STEP 2
- Start the installation under the passenger side of the vehicle. Locate the 6 plugs along the bottom of the body panel. Remove the plastic plugs from each mounting location if equipped.
- Mounting Brackets will bolt to the 1st, 3rd and 6th threaded mounting holes, (Figs 1-4).
- Directly above each threaded insert is a top mounting location on the side of the body panel.
- NOTE: Thread an 8mm Hex Bolt into the threaded inserts to clear paint as required.
- STEP 3
- Assemble Passenger Front Mounting Bracket (PFM) and Pas-senger Front Support Bracket (PFS) with (1) M8X1.25-30mm Hex Bolt, (2) M8 Large Flat Washers and (1) M8 Nylon Lock Nut, (Fig 5). Do not fully tighten at this time.
- STEP 4
- Attach the Assembled Passenger Front Mounting Bracket to the factory threaded holes with (2) M8 X1.25-30mm Hex Bolts, (2) M8 Lock Washers and (2) M8 Large Flat Washers, (Fig 6). Do not fully tighten the hardware at this time.
- STEP 5
- Repeat Steps 3 & 4 to install the Passenger Center Mounting Bracket (PCM/DRM) and Passenger Rear Mounting Bracket (DCM/PRM) on the remaining mounting locations. (Figs 7-8).
- STEP 6
- Once (3) brackets have been installed, select (5) M8X1.25-20mm T-Bolts, and thread (1) M8 Plastic Washer on each T-Bolt, (Fig 9).
- Install the (5) M8X1.25-20mm T-Bolts with plastic washers in the slots on the assembled passenger side step bar. Rotate the T-Bolts to 90 degrees, and thread down the M8 Plas-tic Washers against the step bar (Fig 10).
- NOTE: The Plastic Washer is designed to keep the T-Bolt in place to avoid falling into the tube during installation.
- STEP 7
- Attach the Assembled Passenger Side Step Bar onto the Mounting Brackets with (5) M8 Plastic Washers, (5) M8X1.25-20mm T-Bolts, (5) M8 Large Flat Washers, (5) M8 Nylon Lock Nuts, (Fig 11). Do not fully tighten the hardware at this time.
- NOTE: The Passenger Front Mounting Bracket is located under the front pedal. Slide (1) M6X1-20mm Square Head Bolt into the channel at the bottom of the front pedal (Fig 12).
- And secure the Passenger Front Mounting Bracket to the pedal with (1) M6 Large Flat Washer and (1) M6 Nylon Lock Nut, (Fig 11).
- STEP 8
- Level and adjust the assembled Step Bar properly and tighten all hardware.
- Move to the other side of the vehicle. Repeat Steps 2-7 for the other side step bar installation.
- Attention
- Do periodic inspections of the installation to make sure that all hardware is secure and tight.
- To protect your bars/boards, please use mild soap/non-abrasive products for cleaning only.
Customer Support:
- info@iarmorauto.com.
- Rev. 20230601
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>