iArmor IA-S280H 6.5 Inch Side Armor Stainless Steel Running Boards Installation Guide
- May 15, 2024
- iArmor
Table of Contents
iArmor IA-S280H 6.5 Inch Side Armor Stainless Steel Running Boards
Product Information
Specifications:
- Part Number: IA-S280H
- Mounting Type: Rocker Panel Mount
- Installation Requirement: No Drilling/Trimming Required
- Torque Values:
| Fastener Size | Tightening Torque (ft-lbs) |
|---|---|
| 6mm | 6-7 |
| 8mm | 16-18 |
| 10mm | 31-32 |
| 12mm | 56-58 |
| 14mm | 92-94 |
Product Usage Instructions:
-
Step 1: Passenger Side Installation
Start by removing the existing factory bolts near the front tire opening. Refer to Fig 1 for location. -
Step 2: Passenger Front Mounting Bracket Installation
Select the Passenger Front Mounting Bracket (PFM) and secure it using the provided hardware. Do not fully tighten at this stage. -
Step 3: Passenger Center and Rear Mounting Brackets Installation
Continue to install the Passenger Center Mounting Bracket (PCM/DRM) and Passenger Rear Mounting Bracket (DCM/PRM). Do not fully tighten the hardware yet. -
Step 4: Attaching Passenger Side Step Bar
Attach the Passenger Side Step Bar to the Mounting Brackets using the provided hardware. Do not fully tighten at this time. -
Step 5: Level and Adjust Step Bar
Properly level and adjust the Step Bar before fully tightening all hardware. -
Step 6: Driver Side Installation
Repeat Steps 1-5 for the driver side of the vehicle to complete the installation process.
Frequently Asked Questions (FAQ)
-
Is professional installation recommended for this product?
Yes, we strongly recommend professional installation for the best results. We are not responsible for any damage caused by improper installation. -
What should I do if any parts are missing from the package?
Before starting the installation, ensure all parts are present as listed in the instruction manual. If any parts are missing, please contact our Customer Support at info@iarmorauto.com.
BEFORE INSTALLATION
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMEND-ED. THANK YOU FOR CHOOSING OUR PRODUCT!
Torque Value
| Fastener Size | Tightening Torque (ft-lbs) | Required |
|---|---|---|
| 6mm | 6-7 | X |
| 8mm | 16-18 | √ |
| 10mm | 31-32 | X |
| 12mm | 56-58 | X |
| 14mm | 92-94 | X |
PART LIST
Hardware
Hardware Package A (For Bracket Installation)
| Item | QTY | Description | Item | QTY | Description |
|---|---|---|---|---|---|
| 1# | 6 | U Brackets | 3# | 12 | M8 Large Flat Washers |
| 2# | 12 | M8X1.25-30 Hex Bolts | 4# | 12 | M8 Lock Washers |
Hardware Package B (For Step Bar Installation)
| Item | QTY | Description | Item | QTY | Description |
|---|---|---|---|---|---|
| 1# | 6 | M8X1.25-55mm Carriage Bolts | 3# | 6 | M8 Lock Washers |
| 2# | 6 | M8 Large Flat Washers | 4# | 6 | M8 Hex Nuts |
INSTALLATION INSTRUCTION
The instruction here is for your reference only. We strongly recommend the professional installer for best result. We are not responsible for any damage caused by the installation.
- STEP 1
Start installation on the passenger side of the vehicle, remove the existing (2) factory bolts located by the front tire opening securing the factory rocker panel bracket to the vehicle, (Fig 1).
- STEP 2
Select (1) Passenger Front Mounting Bracket (PFM). Hold the Mounting Bracket (PFM) over the rocker panel bracket and line up the (2) mounting holes. Secure the bracket to the vehicle using the included longer (2) M8X1.25-30mm Hex Bolts, (2) M8 Lock Washers and (2) M8 Large Flat Washers, (Fig 2). Do not tighten hardware at this time.
- STEP 3
Move to the passenger side center and rear mounting loca-tions, (Fig 3). Repeat Steps 1-2 to install the Passenger Center Mounting Bracket (PCM/DRM) and Passenger Rear Mounting Bracket (DCM/PRM) (Fig 4). Do not fully tighten hardware at this time.
-
STEP 4
Once all (3) passenger side mounting brackets are installed, select and attach the Passenger Side Step Bar onto the Mount-ing Brackets with (3) U Brackets, (3) M8X1.25-55mm Carriage Bolts, (3) M8 Large Flat Washers, (3) M8 Lock Washers and (3) M8X1.25 Hex Nuts (Fig 5). Do not fully tighten hardware at this time. -
STEP 5
Properly level and adjust the Step Bar and fully tighten all hard-ware. -
STEP 6
Move to the driver side of the vehicle. Repeat Steps 1-5 to in-stall driver side step bar. Installation completed.
Attention- Do periodic inspections to the installation to make sure that all hardware is secure and tight.
- In order to protect your bars/boards, please use mild soap/non-abrasive products for cleaning only.
Customer Support: info@iarmorauto.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>