DBPOWER G16 Portable Car Jump Starter User Manual
- June 12, 2024
- DBPOWER
Table of Contents
PROTABLE CAR JUMP STRATER G16
USER MANUAL
Power Your Life
1. DO NOT start any engines that exceed the maximum displacement the jump starter can bear.
2. DO NOT crank the engine for more than 3 seconds.
3. Allow the jump starter to cool down for at least 1 minute NOTE between each start attempt.
4. Please ensure the device is at least 50% charged before use.
A Big Thank You
Thank you for choosing G15 Jump Starter and becoming our valued customer. At DBPOWER, we’re committed to providing you with products that enhance your daily life. Happy customers make us proud and we hope that this product will bring you the most convenient and enjoyable experience. If you have any questions or feedback on your new product, just contact our customer support team at 1-855-888-5533, or via email at
Enjoy your new product!
ATTENTION
- This device is suitable for petrol engines (up to 8L) and diesel engines (up to 6.5L). Do not try to start an engine with a capacity greater than the intended one. This can cause damage to the device and possible injury.
- Don’t start the engine more than 3 times. Allow at least 1 minute for the jump starter to cool down after each 3-second start attempt.
- When your jump starter is completely charged, it will perform optimally. If it is less than 50% charged, it will not be able to start the engine.
- Clean your car battery’s electrodes of dust and debris before jump starting.
- If the instructions are followed correctly, but your vehicle doesn’t s tart please wait for 5-10 mins and try again. Do not attempt to start the engine again without initially allowing the device to cool down.
- Do not connect the positive and negative polarity clamps together when the device is powered on. Short circuit can cause electric shock and serious injury.
- Disconnect the cables from the jump starter and car battery when not in use, remove the negative clamp from car battery first (or positive first for positive ground systems).
- Do not charge the device immediately after jump-starting your vehicle. Wait at least 30 mins before charging the device before jump starting.
- To ensure the device’s lifespan, discharge and recharge it at least once every three months.
- Use only the cords that came with the jump starter or other certified cables.
- Keep this product away from children. Keep the jump starter away from liquids. DO NOT disassemble this product.
- Please store and charge the jump starter at a dry and well-ventilated place. Avoid dropping the device and exposing it to extreme temperatures.
SPECIFICATION
| Capacity | Capacity 20800mAh/ 76.96Wh |
|---|---|
| Weight | 615g/ 21.7oz |
| Dimensions | 191 x 87 x 36mm/ 7.5 x 3.4 x 1.4inch |
| In(Out) | Type-C 5V/3A |
| Output 1 | Smart 5V/9V/12V |
| Output 2 | 5V/2.1 A |
| Peak Current | 2000A |
| Starting Current | 1000A |
| Operation Temperature Range | -20 C – 60C/ -41- 140 1 |
ACCESSORIES
AT A GLANCE
- Power Button & Function Key
- LED Flashlight
- Smart 5V/9V/12V USB Output
- 5V/2.1A USB Output
- Type-C 5V/3A Input/Output
- Jumper Cable Socket
- Battery Indicator
- Smart Jumper Cables
HOW TO JUMP START YOUR CAR
1. Press the power button on the Jump Starter. There should be at least 50% of battery level available (charge fully before initial use).
2. Insert jumper cables into the jumper cable socket. The blue light is on.
3. Connect the red clamp to the positive(+) terminal and the black clamp to the negative(-) terminal of the car battery. The indicator light will changes from the blue light to green and blue light is continuously on.
4. Start your engine.
5. Remove clamps and pack away.
HOW TO CHARGE CELLPHONES OR TABLETS
HOW TO USE THE LED FLASHLIGHT
Press and hold the power button for 2 secs to turn on the LED flashlight, short-press to switch modes(high,strobe,SOS),press and hold for 2 secs again to turn it off.
HOW TO RECHARGE THE DEVICE
| Adapter | 5V/1 A | 5V/2A | 5V/3A |
|---|---|---|---|
| Charging time | 14.5h | 9.0h | 6.0h |
Note:
- The charging adapter is not included. Please use a 5V universal adapter to charge the jump starter.
- Charging the jump starter via PC is NOT recommended. This will greatly increase the charging time.
EXCEPTION DESCRIPTION INDICATED BY THE CLAMPS
• NORMAL STANDBY INDICATOR
Wnen the tiLe Ignt is on. the emergency power supply can start theca?.
• OPERATING WSTRUCTIONS
When the Clue and green light is on, it indicates the ca’ can be started.
• LOW VOLTAGE PROTECTION
Wnen the red and blue Ight is continuously on and the buzzer a boec ng. the emergency cower Supply a insulfcent. The dooiee needs to be Italy charged before attempting to start the vehicle.
• REVERSE POLARITY PROMOTION
Foe your safety and that of your vehicle. the device is designed with reverse polarity protection. Wien the red and blue lights are ccranuously on and the buzzer is beeping. the positive and negative clamps have teen connected incorrectly to the car battery. Connect the damps correctly and try again.
• HIGH TEMPERATURE PROTECTION
When red and blue Iights are continuously on and the buzzer is beepng, the high-temperature protection e has been activated. Before using the device again, please give it sane time to cool down
• SHORT-CIRCUIT PROTECTION
When the red and blue Iights are continuously on and the buzzer is beeping, the positive and negative clamps are in contact with each other. Adjust the damps so that they are not in contact with each other, and then try agar.
• JUMP STARTER TIMEOW PROTECTION
The damps will dccomect automaticaly after 30 seconds. Please attempt to start the engine within 30 seconds. If you need to attempt to jump start the engine again after 30 seconds, please remove and reconnect the clamps, then try again.
• HIGH-VOLTAGE PROTECTION
When the red and clue Ight is continuously on and the buzzer is long beeping. the power supply ignition voltage Iimit has been exceeded. It is necessary to discharge the power supply before performing an ignition operation.
Made in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>