ergotron HX Monitor Arm Desk Mount Conversion Kit User Guide
- June 13, 2024
- ERGOTRON
Table of Contents
HX
Monitor Arm Desk Mount Kit
HX Monitor Arm Desk Mount Conversion Kit
Please review this manual before installing your equipment to learn how to use
this product safely. 
Tools Needed
Safety
Remove monitors before loosening desk attachment.
Warning
Move Arm to highest postition before removing equipment or serious personal
injury and/or equipment damage may occur
WARNING! Stored Energy Hazard: The arm mechanism is under tension and
will move up rapidly, on its own, as soon as attached equipment is removed.
For this reason, DO NOT remove equipment unless the arm has been moved to the
highest position! Failure to follow this instruction may result in serious
personal injury andlor equipment damage!
Remove cables
Raise arm to highest position
Warning
Move Ao et pstton befre removig equpment orserios persor iy andor equpment
camage may occur.
WARNING! Stored Energy Hazard: The arm mechanism is under tension and
will move up rapidly, on its own, as soon as attached equipment s removed. For
this reason, DO NOT remove equipment unless the arm has been moved to the
highest position! Failure to follow this instruction may result in serious
personal injury and/or equipment damage!
Caution
2 people required to nstall montr. Caution: May require 2 people to remove
and install monitor.
Remove all monitors and pivots from arm
Remove all monitors and pivots from crossbar
Remove arm
The following instructions are for
attaching your new bracket and reattaching your arm
Warning: Because mounting surface materials can vary widely, it is
imperative that you make sure mounting surface is strong enough to handle
mounted product and equipment.
NOTE: Determine if arm
will typically collapse to the left or right before installation.
NOTE: Determine if arm will typically
collapse to the left o right before installation.
NOTE: Am extension should be at a 45° angle o less when attaching
monitor.
NOTE: Am
extension should be at a 45 angle or less when attaching crossbar.
CAUTION: Monitors are not stable unless
fully secured to crossbar. Failure to tighten screws completely may result in
damage to equipment. 
Caution: Leave enough slack in
cable to allow full range of motion.To avoid the potential to pinch cables it
is important to follow the cable routing instructions in this manual. Failure
to follow these instructions may result in equipment damage or personal
injury.
CAUTION: For Desk Clamp installations: Do Not rotate display past edge of
desk
For the latest User Installation Guide please visit:
www.ergotron.com
~ For Waranty visit:
www.ergotron.com/warranty
For Senvice visit: www.ergotron.com
Forlocal customer care phone numbers visit: http://contact.ergotron.com
Learn more about ergonomic computer use at:
www.ergotron.com/ergonomics
© 2023 Ergotron, Inc. All rights reserved.
While Ergotron, Inc. makes every effort to provide accurate and complete
information on the installation and use of its products it will not be held
liable for any editorial errors or omissions (including those made in the
process of translation from English to another language), or for incidental,
special or consequential damages of any nature resulting from furnishing this
instruction and performance of equipment in connection with this instruction.
Ergotron, Inc.reserves the right to make changes in the product design and/or
product documentation without notification to ts users. For the most current
product information, or to know if this document is available in languages
other than those herein, please contact Ergotron. No part of this publication
may be reproduced,stored in a retrieval system, or transmitted in any form or
by any means,electronic, mechanical, photocopying,recording or otherwise
without the prior written consent of Ergotron, Inc. 1181 Trapp Road, Eagan,
Minnesota, 55121, USA Patents Pending and Patented U.S. & Foreign. Ergotronis
a registered trademark of Ergotron, Inc.
www.ergotron.com
USA: 1-800-888-8458
Europe: +31 (0)33-4545600
China: 400-120-3051
Japan: japansupport@ergotron.com