ANNOVI REVERBERI HOT 1310 N High Pressure Washer Instruction Manual

ANNOVI REVERBERI HOT 1310 N High Pressure Washer

Product Information

The 6640 6670 High Pressure Washer is a professional-grade machine intended for experienced individuals who are familiar with the technical, regulatory, and legislative factors involved in using and maintaining the machine. This product features both cold and hot water operation modes with an adjustable temperature setting. It is rated in insulation class I, meaning it is equipped with a protective earthing conductor (only if the symbol appears on the machine), and complies with relevant European directives. The E1 symbol indicates that the machine must not be disposed of as municipal waste and that its electrical and electronic parts must not be reused for improper uses since they contain substances that constitute health hazards.

Product Usage Instructions

1. Read the instructions carefully before use.
2. Keep the instructions for future reference.
3. Check that the symbols and signs affixed to the machine are always present and legible; otherwise, fit replacements in the original positions.
4. Do not touch moving parts.
5. Ensure the machine is intended for professional use only and not intended for use by children, persons with impaired physical, sensory or mental capabilities, or persons without the necessary experience and knowledge.
6. Wear ear defenders.
7. Use the machine in compliance with local regulations that may prohibit connection of the product to the drinking water supply system.
8. Do not direct the water jet at people, animals, electrical equipment or the product itself.
9. When using the machine, ensure that the temperature setting is adjusted appropriately for either cold or hot water operation mode.
10. If disposing of the machine, do not dispose of it as municipal waste. Instead, hand it over to the dealer on purchase of a new machine. The machine’s electrical and electronic parts must not be reused for improper uses since they contain substances that constitute health hazards.

SAFETY INSTRUCTIONS

The machine you have purchased is a technologically advanced product manufactured by one of the leading European producers of high pressure washers. This information is provided to enable you to get the best from your machine; please read it carefully and always comply with its recommendations. During connection, use and maintenance of the machine, take all possible precautions to protect your own safety and that of the people in the immediate vicinity. Read the safety regulations carefully and comply with them on all occasions; failure to do so may put health and safety at risk or cause expensive damage.

SAFETY SIGNS

Comply with the instructions provided by the safety signs fitted to the machine and those contained in this manual. The machine and manual only feature the symbols relevant to the model purchased.
Check that the symbols and signs affixed to the machine are always present and legible; otherwise, fit replacements in the original positions.
Warning – Danger
Read these instructions carefully before use.
E2 symbol – Indicates that the machine is intended for professional use, i.e. for experienced people familiar with the relative technical, regulatory and legislative factors and capable of performing the operations involved in using and maintaining the machine. This machine is not intended for use by children, persons with impaired physical, sensory or mental capabilities, or persons without the necessary experience and knowledge.
Moving parts. Do not touch.
0/OFF Switch “OFF” position
I/ON Switch “ON” position
Guaranteed sound power level
Cold water operation
Hot water operation
Temperature setting
Prohibition sign, informs users that local regulations may prohibit connection of the product to the drinking water supply system.
Danger sign, warns users not to direct the water jet at people, animals, electrical equipment or the product itself.
This product is rated in insulation class I. This means that it is equipped with a protective earthing conductor (only if the symbol appears on the machine).
The product complies with the relevant European directives.
E1 symbol – Indicates that the machine must not be disposed of as municipal waste; it may be handed in to the dealer on purchase of a new machine. The machine’s electrical and electronic parts must not be reused for improper uses since they contain substances which constitute health hazards.
Wear ear defenders.
Wear a protective mask.
Wear respiratory protection.
Wear protective gloves.
Wear safety footwear.
Wear protective clothing.
Burn hazard! Warning: Hot components!
Poisoning hazard! Do not inhale exhaust gases.

SAFETY RULES/RESIDUAL RISKS

• SAFETY “DO NOTS”
• Warning. DO NOT allow children to use the machine; supervise them to ensure that they do not play with it.
• Warning. High pressure jets may be dangerous if incorrectly used.
• Warning. DO NOT use the machine with flammable or toxic liquids, or any products which are not compatible with its correct operation. Use of the machine in a potentially inflammable or explosive atmosphere is forbidden.
• Warning. EXPLOSION HAZARD. DO NOT use the machine to spray flammable liquids.
• Warning. DO NOT point the water jet at people or animals.
• Warning. DO NOT point the water jet at the machine itself, electrical parts or other electrical equipment.
• Warning. DO NOT use the machine with people within its range of action unless they are wearing protective clothing.
• Warning. DO NOT point the jet at yourself or others to clean clothing or footwear.
• Warning. DO NOT use the machine outdoors when it is raining.
• Warning. The machine MUST NOT be operated by children, incompetent persons or anyone who has not read and understood the instructions.
• Warning. DO NOT touch the plug and/or socket with wet hands.
• Warning. DO NOT use the machine if the power cable is damaged. If the power cable is damaged, it must be replaced by the manufacturer, one of its Authorised Service Centres or similarly qualified persons in order to avoid a safety hazard.
• Warning. DO NOT use the machine if a power cable or important parts such as the safety devices, high pressure hoses or trigger gun are damaged.
• Warning. DO NOT jam the gun trigger in the operating position.
• Warning. Check that the data plate is affixed to the machine; if not, inform your dealer. Machines without data plates must NOT be used as they are unidentifiable and potentially dangerous.
• Warning. DO NOT tamper with or adjust the setting of the regulating valve or the safety devices.
• Warning. DO NOT alter the original diameter of the nozzle jet.
• Warning. DO NOT move the machine by pulling on the POWER CABLE.
• Warning. DO NOT allow vehicles to drive over the high pressure hose.
• Warning. DO NOT move the machine by pulling on the high pressure hose.
• Warning. When directed towards tyres, tyre valves or other pressurised components, the high pressure jet is potentially dangerous. Do not use the rotary nozzle kit, and always keep the jet at a distance of at least 30 cm during cleaning.
• Warning. The use of non-original accessories and any other accessories not specifically intended for the model in question is prohibited. All modifications to the machine are prohibited; any modifications shall render the Declaration of Conformity null and void and relieve the manufacturer of all liability under civil and criminal law.
• Warning. DO NOT use unsuitable diesels as this may be hazardous or damage the machine.
• Warning. DO NOT touch the boiler or the exhausts during operation. Burning hazard.

SAFETY “MUSTS”

• Warning. All electrical conductors MUST BE PROTECTED against the water jet.
• Warning. The electric supply connection must be made by a qualified electrician and comply with IEC 60364-1. Either a residual current device that will cut off the power supply to this machine if the leakage current to earth exceeds 30 mA for 30 ms or a ground fault interrupt device must be installed.
• Warning. DURING start-up, the machine may cause network noise.
• Warning. Use of a residual current device will provide additional protection for the operator (30 mA).
• Warning. Models supplied without plug must be installed by qualified staff.
• Warning. Use only approved electrical extension leads with suitable conductor cross-section.
• Warning. Always turn off the switch when leaving the machine unattended.
• Warning. High pressure may cause parts to rebound: wear all the protective clothing (PPE) and equipment needed to ensure the operator’s safety.
• Warning. Before doing work on the machine, REMOVE the plug.
• Warning. Before pressing the trigger, GRIP the trigger gun firmly to counteract the recoil.
• Warning. COMPLY WITH the local water supply authority regulations. Under IEC 60335-2-79, the machine may only be connected to the mains drinking water supply if the supply hose is fitted with a backflow preventer valve with drain facility corresponding to EN 12729 type BA. The backflow preventer valve may be ordered from the manufacturer.
• Warning. Water that has passed through backflow preventers is considered to be non-potable.
• Warning. Maintenance and/or repair of electrical components MUST be carried out by qualified staff.
• Warning. DISCHARGE residual pressure before disconnecting the hose from the machine.
• Warning. CHECK before each use and at regular intervals that the screws are fully tightened and that there are no broken or worn parts.
• Warning. ONLY USE detergents which will not corrode the coating materials of the high pressure hose / power cable.
• Warning. KEEP people or animals at least 15 m away.
• Warning. This machine is designed for use with the detergents supplied or recommended by the manufacturer. The use of other detergents or chemicals may adversely affect the machine’s safety.
• Warning. Do not allow the detergent to come into contact with the skin, and the eyes in particular! In case of contact with eyes, rinse with plenty of water and seek medical advice at once!
• Warning. High pressure hoses, fittings and joints are important for the machine’s safety. Use only high pressure hoses, fittings and joints recommended by the manufacturer.
• Warning. To ensure the machine’s safety, only use the manufacturer’s genuine parts, or other parts which carry its approval.
• Warning. If an extension cable is used, the plug and socket must be watertight.
• Warning. Unsuitable extension cables can be dangerous. If an extension cable is used, it must be suitable for outdoor use, and the connection must be kept dry and off the ground. Use of a power cable reel which keeps the socket at least 60 mm above the ground is strongly recommended.
• Warning. Switch the machine off and disconnect it from the power supply before assembly, cleaning, adjustments, maintenance, storage and transportation.
• Warning. Insert the drain pipe cleaning kit down to the red mark before turning the machine on.
• Warning. Do not leave the machine in operation unattended
• Warning. When filling up, do not allow diesel to come into contact with hot parts.
• Warning. If using the machine indoors, ensure that there is sufficient ventilation and that exhaust gases are vented correctly (Poisoning hazard). The exhaust gas vent hole must not be closed. Make sure that no exhaust gases are emitted close to the air intakes.
• Warning. The motor must not be running during transportation of the machine. Also ensure that the machine is in a firm, stable position.
• Warning. Switch the machine off before assembly, cleaning, adjustments, maintenance, storage and transportation

GENERAL INFORMATION (FIG.1)/PAGE 3

Use of the manual
The manual forms an integral part of the machine and should be kept for future reference. Please read it carefully before installing/ using the machine. If the machine is sold, the seller must pass on this manual to the new owner along with the machine.

Delivery
The machine is delivered partially assembled in a cardboard box. The supply package is illustrated in fig.1.
Documentation supplied with the machine

• A1 Use and maintenance manual
• A2 Safety instructions
• A3 Declaration of conformity
• A4 Warranty regulations

Disposing of packaging
The packaging materials are not environmental pollutants but must still be recycled or disposed of in compliance with the relevant legislation in the country of use.

TECHNICAL INFORMATION (FIG.1)/PAGE 3

Intended use
This machine has been designed for individual use for the cleaning of vehicles, machines, boats, masonry, etc., to remove stubborn dirt using clean water and biodegradable chemical detergents. Vehicle engines may be washed only if the dirty water is disposed of as per regulations in force.

• Inlet water temperature: see machine data plate.
• Inlet water pressure: min. 0.1 MPa – max. 1 MPa.
• Operating ambient temperature: above 0 °C.
  The machine is compliant with the IEC 60335-1 and IEC 60335-2-79 standards.

Operator
The symbol in fig.1 identifies the machine’s intended operator.

Main components

• B2 Lance
• B3 Trigger gun with safety catch
• B4 Power cable
• B5 High pressure hose
• B6 Detergent tank
• B7 Oil cap
• B8 Diesel tank
• B10 Diesel filter
• B12 Boiler exhaust
• B13 Detergent filter
• E Nozzle
• G Pressure regulator
• L Water filter
• V Water nozzle
• Z Control panel

Accessories (where supplied – see fig.1)

• C2 Rotary nozzle kit
• C3 Handle
• C5 Hose reel
• C9 Adaptor
• C10 Screws
• C11 Brackets
• C12 Lever
• C13 Detergent kit
• C14 Wheels
• C16 Pressure gauge

Control panel (see fig.1)

• Machine switch (H) OFF/0 – ON/I Cold water operation.
• Hot water operation switch (T) 0/OFF – ON/I Hot water operation.
• Temperature setting thermostat (Y) for hot water operation.

Safety devices

• Starter device (H). The starter device prevents accidental use of the machine.

• Boiler starter device (T).

• Lack of water device The device prevents the boiler from operating without water.
  Warning – danger! Do not tamper with or adjust the safety valve setting.

• Safety and/or relief valve. The safety valve is also a relief valve.

• Safety catch (D): prevents accidental emission of water jet.

• Overload cutout: stops the machine in case of overload.

INSTALLATION (FIG.2)/PAGE 4

Assembly
Warning – danger! All installation and assembly operations must be performed with the machine disconnected from the mains power supply. The assembly sequence is illustrated in fig.2.

Fitting the rotary nozzle
(For models with this feature). The rotary nozzle kit delivers greater washing power. Use of the rotary nozzle may cause a reduction in pressure of 25% compared to the pressure obtained with the adjustable spray nozzle. However, the rotary nozzle delivers greater washing power due to the rotation of the water jet.

Electrical connection
Warning – danger! Check that the electrical supply voltage and frequency (V-Hz) correspond to those specified on the data plate (fig.2). Use of extension cables The cross-section of the extension cable should be proportional to its length; the longer it is, the greater its cross-section should be. See table I.

Water supply connection
Warning – danger! Only clean or filtered water should be supplied to the machine. The flow rate of the water inlet tap must be equal to that of the pump. Place the machine as close to the water supply system as possible.

Connection points

• l Water outlet (OUTLET)
• n Water inlet with filter (INLET)

Connection to the mains water supply: The machine may only be connected directly to the mains drinking water supply if the supply hose is fitted with a backflow preventer valve with drain facility as per current regulations in force. Make sure that the hose is at least Ø 13 mm, that it is reinforced and that it is not more than 25 m long.

ADJUSTMENTS (FIG.3)/PAGE 5

Adjusting the detergent pressure
To deliver detergent at the correct pressure, set the nozzle (E) on ” ” as shown.

Setting the temperature
When operating with hot water, use the thermostat (Y) to set the working temperature required.

INFORMATION ON USE OF THE MACHINE (FIG.4)/PAGE 5

Controls

• Starter device (H). Set the starter device on (ON/I) to start the motor. In this position, the device also enables operation with hot water if required. If there is a pilot light on the starter device, it should light up. Set the starter device on (OFF/0) to stop the machine. If there is a pilot light on the starter device, it should go out. Hot water operation device (T). Set the hot water operation device on (ON/I) to start the boiler. If there is a pilot light on the starter device, it should light up. Set the starter device on (OFF/0) to stop the boiler. If there is a pilot light on the hot water operation device, it should go out.
• Temperature setting thermostat (Y) (See 7.3).
• Water jet trigger (I).
  Warning – danger! During operation the machine must be positioned as shown in fig.4 on a firm, stable surface.

Start-up (see fig.4)

1. Turn on the water supply tap fully.
2. Release the safety catch (D).
3. Depress the gun trigger for a few seconds and start up the machine by setting the starter device (H) on (ON/I).
   Warning – danger! Before starting up the machine check that it is receiving water correctly; use of the machine without water will damage it. Do not cover the ventilation grilles when the machine is in use. When the gun trigger is released the dynamic pressure automatically cuts out the electric motor with a delay of about 15 seconds. When the gun trigger is depressed the automatic drop in pressure starts the motor and the pressure is restored after a very slight delay; If the machine is to function correctly, all gun trigger releasing and depressing operations must be at least 4-5 seconds apart. To prevent damage to the machine, do not allow it to operate dry and check that it is properly supplied with water at all times.

Stopping

1. Set the starter device on (OFF/0).
2. Depress the gun trigger and discharge the residual pressure (H) inside the hoses.
3. Engage the safety catch (D).

Restarting

1. Release the safety catch (D).
2. Depress the gun trigger and discharge the residual air inside the hoses.
3. Set the starter device on (ON/I).

Start-up with hot water

1. Fill the diesel tank (B8) using automotive diesel only.
2. Repeat points 1, 2 and 3 of section 8.2.
3. Check that the thermostat (Y) is on 0 °C-OFF.
4. Turn on the boiler using the switch (T).
5. Wait 30 seconds for the diesel circuit to fill.
6. Turn the thermostat (Y) to the required temperature to light the burner. Once the required temperature is reached, the boiler will cut out automatically, relighting whenever the temperature falls.

Storage

1. Return the thermostat (Y) to zero.
2. Operate the machine with cold water for 2 minutes to cool it.
3. Turn off the boiler switch (T).
4. Turn off the water supply tap.
5. Discharge the residual pressure from the trigger gun until all the water has come out of the machine.
6. Switch the machine off (OFF/0).
7. Remove the plug from the socket.
8. Drain and wash out the detergent circuit at the end of the working session. To wash out the detergent circuit, use clean water instead of the detergent.
9. Engage the trigger gun safety catch (D).

Filling with and using detergent
The detergent must be delivered using the accessories and by the procedures described in point 7.1. Use of a high pressure hose longer than the one originally supplied with the machine, or the use of an additional hose extension, may reduce or completely halt the suction of detergent from a tank (on machines with this feature)/detergent suction kit.

Filling with diesel
Check the diesel level and if necessary fill up with automotive diesel (see data plate) before each use with hot water. Take great care not to spill diesel on hot surfaces.

Recommended cleaning procedure
Dissolve dirt by applying the detergent to the surface while still dry. When dealing with vertical surfaces work from the bottom upwards. Leave the detergent to act for 1-2 minutes but do not allow the surface
to dry. Starting from the bottom, use the high pressure jet at a minimum distance of 30 cm. Do not allow the rinse water to run onto unwashed surfaces. In some cases, scrubbing with brushes is needed to remove dirt. High pressure is not always the best solution for good washing results, since it may damage some surfaces. The needle jet setting of the adjustable spray nozzle and the rotary nozzle should not be used on delicate or painted parts, or on pressurised components (e.g. tyres, inflation valves, etc.). Effective cleaning depends on both the pressure and volume of the water used, to the same degree.

ROUTINE MAINTENANCE (FIG.5)/PAGE 6

Any maintenance operations not covered by this chapter should be carried out by an Authorised Sales and Service Centre.
Warning – danger! Always disconnect the plug from the power socket before carrying out any work on the machine.
Inspect the power cable, high pressure hose, fittings, trigger gun and lance at each use.

Cleaning the nozzle

1. Disconnect the lance from the trigger gun.
2. Remove any dirt deposits from the nozzle hole using the tool (C1).

Cleaning the filters
Inspect the inlet filter (L), the detergent filter (where fitted) and the diesel filters before each use, and if necessary clean in accordance with the instructions. Replace the filters if necessary.

Oil level
Check the pump oil level and add oil through the intake hole to restore the correct level. Refer to the “Technical data” table for the oil characteristics.

End-of-season storage
Before putting the machine into store for the winter, run it with nonaggressive, non-toxic antifreeze. Put the machine in a dry place, protected from frost. 10

EXTRAORDINARY MAINTENANCE

Warning – danger! Extraordinary maintenance must be performed by an authorised sales and service centre.

• Check the hydraulic circuit, inspect the fixtures and mountings for damage and check the boiler electrode setting every 200 working hours.
• Replace the oil, electrodes, nozzles and filters every 500 working hours.
• Clean the boiler and descale the heating coil every 500 working hours.
• Check the safety devices every 500 working hours.

STORAGE AND TRANSPORTATION (FIG.5)/PAGE 6

• Store the accessories as shown in fig.5.
• Transport the machine as shown in fig.5.

TROUBLESHOOTING

The pump runs but does not reach the specified pressures / uneven pressure / pressure drops| Water supply tap turned off| Check and turn on the tap
Regulating valve seat worn| Replace the valve seat Contact an Authorised Service Centre
Water nozzle worn or unsuitable| Replace water nozzle
Worn gaskets| Replace the gaskets Contact an Authorised Service Centre
Water filter fouled| Clean the water filter
Worn intake and/or delivery valves| Replace the valves Contact an Authorised Service Centre
Dirt in the valves, interfering with their operation| Check and clean Contact an Authorised Service Centre
Air being sucked into system| Check the intake pipelines
Safety valve leaking| Check the safety valve Contact an Authorised Service Centre
Calcium deposits in circuit| Check and clean Contact an Authorised Service Centre
Boiler smoking| Water in diesel tank| Drain the tank and fill it with diesel
Diesel pressure not correct| Contact an Authorised Service Centre
Ignition electrodes not correctly positioned| Contact an Authorised Service Centre
Diesel nozzle fouled| Clean the diesel nozzle Contact an Authorised Service Centre
Diesel nozzle worn| Replace the diesel nozzle Contact an Authorised Service Centre
Heating coil obstructed| Clean the heating coil Contact an Authorised Service Centre
Diesel pump fouled| Clean the diesel pump Contact an Authorised Service Centre
Diesel solenoid valve not working| Replace the diesel solenoid valve Contact an Authorised Service Centre
Boiler shuts off| Lack of diesel| Fill the diesel tank
Plastic coupling between diesel pump and boiler motor worn, diesel pump worn, boiler motor not working| Replace: the diesel pump coupling or the boiler motor Contact an Authorised Service Centre
Diesel tank empty| Fill the tank
The filter on the diesel intake pipe is fouled| Clean the diesel filter
Water in diesel tank| Drain the tank and replace the diesel
Pressure switch not working| Replace the pressure switch Contact an Authorised Service Centre
Ignition transformer has failed| Replace the ignition transformer Contact an Authorised Service Centre
Ignition electrodes not correctly positioned| Contact an Authorised Service Centre
Diesel nozzle fouled| Clean the diesel nozzle Contact an Authorised Service Centre
Diesel nozzle worn| Replace the diesel nozzle Contact an Authorised Service Centre
Diesel pump damaged| Replace the diesel pump Contact an Authorised Service Centre
Diesel solenoid valve not working| Replace the diesel solenoid valve Contact an Authorised Service Centre
Problems| Probable causes| Remedies
---|---|---
Water in pump oil| Casing end O-rings worn| Replace O-rings

Contact an Authorised Service Centre

High air humidity level| Change the oil twice as often as recommended
Gaskets worn out| Replace the gaskets Contact an Authorised Service Centre
Noise/vibrations| Air being sucked into system| Check the tightness of the intake pipelines
Water filter fouled| Clean the water filter
Water supply insufficient| Make sure that water is available to the machine at a flow rate higher than that of the pump
Worn intake and/or delivery valves| Replace the valves Contact an Authorised Service Centre
Dirt in intake and/or delivery valves| Check and clean the valves Contact an Authorised Service Centre
Worn bearings| Replace the bearings Contact an Authorised Service Centre
Pumped liquid too hot| Reduce pumped liquid temperature
Water seeping from drains between casing and pump head| Worn gaskets| Replace the gaskets Contact an Authorised Service Centre
Worn pistons| Replace the pistons Contact an Authorised Service Centre
Piston cap O-rings worn| Replace the piston cap O-ring Contact an Authorised Service Centre
Oil seeping from drains between casing and pump head| Casing end O-rings worn| Replace O-rings Contact an Authorised Service Centre
The machine shuts off and will not restart| ** No power being received| Check that the plug is firmly connected to the socket and the line is receiving power
Motor thermal protector tripped| Wait for the thermal protector to reset
Water temperature too low| Thermostat not set on the temperature required| Set the thermostat on the temperature required
Thermostat has failed| Replace the thermostat Contact an Authorised Service Centre
Calcium deposits in water circuit| Clean the water circuit Contact an Authorised Service Centre
Boiler partially fouled with soot| Clean the boiler Contact an Authorised Service Centre
Water nozzle worn| Replace water nozzle
No detergent sucked in| Adjustable spray nozzle on high pressure setting| Set nozzle ( E** ) to “   ” (fig.3)
Detergent too dense| Dilute with water
High pressure hose extension being used| Fit original hose
Deposits or restriction in detergent circuit| Flush with clean water and eliminate any restrictions. If the problem persists, contact an Authorised Service Centre.

If the motor stops and does not restart during operation, wait 2-3 minutes before repeating the start-up procedure (Overload cutout has been  tripped). If the problem recurs more than once, contact the Authorised Service Centre.

EC Declaration of conformity
We, Annovi Reverberi S.p.A, declare that the following Machine(s):

• Designation of machine High pressure washer
• Model No. 6640 6670 HOT 1310 N HOT 1713
• Rated power 3 kW 5 kW 3 kW 5 kW
• Rated flow rate 600 l/h 780 l/h 600 l/h 780 l/h

is (are) compliant with the following European directives: 2006/42/EC, 2014/35/EU, 2011/65/EU, 2015/863/EU, 2012/19/EU, 2014/30/EU, 2000/14/EC (Italian Legislative Decree 262/2002); and is (are) manufactured in accordance with the following standards or standardised documents: EN 60335-1; EN 60335-2-79; EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-3; EN 61000-3-11; EN 60704-1; EN 62233; EN IEC 63000. Name and address of the person appointed to issue the technical file: Stefano Reverberi / AR Managing Director Via ML King, 3 – 41122 Modena – Italy The conformity assessment procedure required by Directive 2000/14/EC has been performed in accordance with Annex V.

• Model No. 6640 6670 HOT 1310 N HOT 1713
• Measured sound power level: 93 dB (A) 92 dB (A) 93 dB (A) 92 dB (A)
• Guaranteed sound power level: 94 dB (A) 93 dB (A) 94 dB (A) 93 dB (A)

Date: 10.05.2022 – MODENA (I) Stefano Reverberi / Managing Director

Warranty
The validity of the warranty is in accordance with the relevant legislation in the country where the product is sold (unless otherwise stated by the producer). The warranty covers materials, construction and conformity defects during the warranty period, during which time the manufacturer will replace defective parts and repair the product if not excessively worn, or replace it. The warranty does not cover components subject to normal wear and tear (valve, piston, water gasket, oil gasket, springs, O-rings, accessories such as the hose, trigger gun, brushes, wheels, etc.). The warranty does not cover defects caused by or arising from:

• improper use, misuse, negligence,
• professional use or hire, if the product was sold for domestic use,
• failure to comply with the maintenance instructions provided in this manual,
• repair by unauthorized staff or centers,
• use of non-genuine parts or accessories,
• damage caused by transport, by dirt or foreign bodies, accidents,
• storage or warehousing problems. Proof of purchase must be submitted to obtain warranty cover.

For after-sales service, contact the store where the machine was purchased.

Technical Data

Technical Data (EN)| Unit| 6640| 6670| HOT 1310 N| HOT 1713
---|---|---|---|---|---
Flow rate| L/min| 10| 13| 10| 13
Maximum flow rate| L/min| –| –| –| –
Pressure| MPa| 12.5| 16.5| 12.5| 16.5
Maximum pressure| MPa| 13| 17| 13| 17
Power| kW| 3| 5| 3| 5
Burner power| kW| 41.9| 41.9| 41.9| 41.9
Maximum inlet temperature| °C| 60| 60| 60| 60
Maximum operating temperature| °C| 90| 90| 90| 90
Maximum inlet pressure| MPa| 1| 1| 1| 1
Trigger gun repulsive force at maximum pressure| N| 24.8| 37| 24.8| 37
Pump oil type| kg| 0.28

SAE 15W40

| 0.30

SAE 15W40

| 0.28

SAE 15W40

| 0.30

SAE 15W40

Protection class| –| I /| I /| I /| I /
Motor insulation| Class| F| F| F| F
Motor protection| –| IPX5| IPX5| IPX5| IPX5
Voltage| V/Hz| 230/50 ~| 400/50 3~| 230/50 ~| 400/50 3~
Maximum permitted electrical system impedance| Ω| –| –| –| –
Sound pressure level LPA (EN 60704-1) (K = 2.5 dB(A))| dB (A)| 85.8| 84.9| 85.8| 84.9
Sound power level LWA (EN 60704-1) (K = 2.5 dB(A))| dB (A)| 94| 93| 94| 93
Machine vibrations (K = 1 m/s2):| m/s2| <2.5| <2.5| <2.5| <2.5
Weight| kg| 95| 98| 95| 98

Manufactured and distributed by: Annovi Reverberi S.p.A.
Via M.L. King 3
41122 Modena (Italy)
www.annovireverberi.it

References

• Annovi Reverberi

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>