PROGRESS LIGHTING P500409 Copeland Brushed Gold Mid-century Etched Glass Geometric Led Instruction Manual
- June 9, 2024
- PROGRESS LIGHTING
Table of Contents
P500409 Copeland Brushed Gold Mid-century Etched Glass Geometric Led
Instruction Manual
PACKAGE CONTENTS
| PART | DESCRIPTION | QUANTITY |
|---|---|---|
| A | Fixture | 1 |
| B | Glass shade | 1 |
| C | Coupling | 1 |
| D | Glass Holder | 1 |
| E | Bracket | 1 |
HARDWARE CONTENTS (not actual size)
Safety Information
Please read and understand this entire manual before attempting to assemble,
operate or install the product.
CAUTION: Read instructions carefully and turn electricity off at main
circuit breaker panel before beginning installation.
CAUTION: Risk of fire. Min. 90°C supply conductors. Consult a qualified
electrician to ensure correct branch circuit conductor.
WARNING: If any Special Control Devices are used with this fixture,
follow instructions carefully to assure full compliance with N.E.C.
requirements. If there are any questions, contact a qualified electrical
contractor.
CAUTION: All glass is fragile. Use care when handling glass shades and
bulbs.
Preparation
- Before beginning installation, make sure all parts are included using the contents diagrams from page 1. If any part is missing or damaged, do not attempt to assemble, install or operate the product.
- Estimated assembly time: 30 minutes.
- Tools required for assembly (not included): Phillips screwdriver, pliers, wire stripper, safety glasses, electrical tape, ladder.
Care and Maintenance
Shut off main power supply before cleaning product or changing light bulbs. To clean, wipe with damp cloth. Do not use abrasive cleaners or cleaners that contain alcohol.
Assembly Instructions
-
Screw screw (AA) onto round mounting plate (CC) and use hex nut (DD) to secure it tightly.
-
Attach assembled parts from step 1 onto outlet box using the mounting screws supplied with the outlet box (not included). NOTE:During this step, determine the hanging length of your fixture by removing stems and optionally cutting the electrical and ground wire to length.
Do NOT cut electrical or ground wires until this overall length is determined. Leave AT LEAST 6 inches MINIMUM of wire past the canopy to allow for easy connections in step 4. -
Once hanging length is determined, pass wires through pipe (HH), pipe (GG) and nipples (ii), tightening pipes to assembly as you go to avoid twisting the wires.
Pass the wires through the swivel (KK) and out of the canopy (LL), then tighten the pipe (GG) to the swivel.
-
Strip 3/8″ of insulation from the electrical wire ends. Using wire nuts (BB), connect white fixture wire to the white supply wire from the outlet box; connect the black fixture wire to the black supply wire.
Connect the fixture ground wire and supply ground wire using a wire nut or by fastening to the ground screw on the round mounting plate. Push all wire connections into the outlet box. -
Slip the canopy (A) holes onto the screws (AA) and attach the fixture to the ceiling surface using the cylinder nuts (EE). Secure tightly.
-
Turn the coupling (C) counter-clockwise to separate the glass holder (D) from the bracket (E).
-
Screw the lamp (not included) into the fixture socket. Use a 75-watt MAX incandescent medium base lamp, SBCFL or SBLED.
Slip the glass shade (B) up and over and set it evenly on the bracket (E). -
With the glass shade (B) resting evenly on the bracket (E), turn the coupling (C) clockwise back onto the glass holder (D) securing the glass shade (B) in place.
WARRANTY AND EXCLUSIVE REMEDY
Progress products, when properly installed and under normal conditions of use,
are warranted to our customers only to be free from defects in material and
workmanship at time of shipment. All warranty claims must be asserted within
one year from date of purchase of the subject items; thereafter, warranty
claims will not be honored. Customers’ sole remedy for a warranty claim or
otherwise shall be limited to repair or replacement of the subject product if
it is shown to have been defective in material or workmanship at time of
shipment. Progress’s sole and maximum liability for a defective product shall
never exceed the cost of the subject product. EXCEPT FOR SUCH A WARRANTY AND
EXCLUSIVE REMEDY AS STATED (AND THE EXPRESS WARRANTY OF TITLE), WE DISCLAIM
ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED, AND SPECIFICALLY DISCLAIM
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. IN NO EVENT SHALL WE BE LIABLE TO CUSTOMER IN WARRANTY, CONTRACT,
NEGLIGENCE, STRICT LIABILITY OR OTHERWISE, FOR ANY DAMAGES, WHETHER INCIDENTAL
OR CONSEQUENTIAL, WHICH ARE ALLEGED TO BE CAUSED BY ONE OR MORE OF OUR
PRODUCTS, BEYOND THE COST TO THE CUSTOMER OF THE SUBJECT PRODUCT OR PRODUCTS.
Therefore, the customer’s sole and exclusive remedy against us for breach of
the warranty, breach of contract or negligence or strict liability or
otherwise shall be limited to repair or replacement of the subject product at
our option (excluding installation and removal charges which shall not be our
liability) or, if we choose, refund of the purchase price. In no case does our
warranty and exclusive remedy extend to anybody other than our customers. Our
customers are not authorized to extend warranties or remedies on our behalf to
anyone. Such unauthorized extensions of warranties or remedies by the customer
shall remain customer’s responsibility. Customer is responsible for
determining the suitability of our products for customer’s use or resale, or
for incorporating them into objects or for applications which customer
designs, assembles, constructs or manufactures.
93164281
Missing parts? Please contact Customer Service at
1-800-447-0573, 8am-8pm (Eastern),
Monday
Friday, or at
customerservice@progresslighting.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>