PROGRESS LIGHTING P810042 Fairway Collection 7 inch White LED Surface Mount Light Instruction Manual
- May 15, 2024
- PROGRESS LIGHTING
Table of Contents
7 INCH LED SURFACE MOUNT
P810042-028-30
PACKAGE CONTENTS
| PART | DESCRIPTION | QUANTITY |
|---|---|---|
| A | Fixture | 1 |
| B | Diffuser | 1 |
HARDWARE CONTENTS (not actual size)
|
---|---
Screw (#8-32)
Qty:2| Wire Nut
Qty:3
Safety Information
Please read and understand this entire manual before attempting to assemble,
operate or install the product.
CAUTION: Read instructions carefully and turn electricity off at main
circuit breaker panel before beginning installation.
CAUTION: Risk of fire. Min. 90°C supply conductors. Consult a qualified
electrician to ensure correct branch circuit conductor.
WARNING: If any Special Control Devices are used with this fixture,
follow instructions carefully to assure full compliance with N.E.C.
requirements. If there are any questions, contact a qualified electrical
contractor.
Preparation
- Before beginning installation, make sure all parts are included using the contents diagrams from page 1. If any part is missing or damaged, do not attempt to assemble, install or operate the product.
- Estimated assembly time: 30 minutes.
- Tools required for assembly (not included): Phillips screwdriver, pliers, wire stripper, safety glasses, electrical tape, ladder.
Care and Maintenance
Shut off main power supply before cleaning product or changing light bulbs. To clean, wipe with damp cloth. Do not use abrasive cleaners or cleaners that contain alcohol.
Assembly Instructions
-
Screw down the screws (AA) into the junction box, but only screw them down halfway.
-
Rotate the diffuser (B) counterclockwise and then remove from the fixture (A).
-
Strip 3/8″ of insulation from the electrical wire ends.
Using wire nuts (BB), connect the WHITE fixture wire to the WHITE supply wire from the junction box; connect the BLACK fixture wire to the BLACK supply wire from the junction box.
Connect the fixture ground wire and supply ground wire using a wire nut.
Push all of the wire connections carefully into the junction box.
-
Push the fixture (A) through the screws (AA) that are halfway tightened on the J-Box. Use the larger hole of the keyhole slot to allow the screwheads to pass through the fixture. Then rotate the fixture clockwise so that the screw heads secure into the smaller side of the keyhole slot. Finally, tighten the screws (AA) all the way down firmly into the J-Box.
-
Rotate the diffuser (B) back onto the fixture (A) through the slot. Twist clockwise and make sure that the lens is secured tightly enough to not fall.
-
Secure the fixture (A), verify that the fixture is flush with ceiling.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful nterference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used n accordance with the
nstructions, may cause harmful interference to radio communications.However,
there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the nterference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
THANK YOU for selecting Progress Lighting
We can assist you with questions regarding product information, assembly or
missing parts
93166152
800-447-0573
8am-8pm (Eastern), Monday-Friday
customerservice@progresslighting.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>