PROGRESS LIGHTING Z-2030 LED Black Contemporary Medium Outdoor Light Instruction Manual

PROGRESS LIGHTING Z-2030 LED Black Contemporary Medium Outdoor Light

PACKAGE CONTENTS

HARDWARE CONTENTS

(not actual size)

Safety Information

• Please read and understand this entire manual before attempting to assemble, operate, or install the product.
• CAUTION: Read instructions carefully and turn the electricity off at the main circuit breaker panel before beginning installation.
• CAUTION: Risk of fire. Min. 90°C supply conductors. Consult a qualified electrician to ensure the correct branch circuit conductor.
• WARNING: If any Special Control Devices are used with this fixture, follow instructions carefully to ensure full compliance with
• N.E.C. requirements. If there are any questions, contact a qualified electrical contractor.
• CAUTION: All glass is fragile. Use care when handling glass shades and bulbs.
• THIS PRODUCT MUST BE INSTALLED BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED, UNDER THE APPLICABLE INSTALLATION CODE.
• KEEP THESE INSTALLATION INSTRUCTIONS
• WARNING – To comply with the National Electrical Code and Underwriters Laboratories requirements, when installed outdoors, or in wet locations, the edge of the wall plate coming in contact with the mounting surface, must be sealed with a latex waterproof caulking to prevent water from entering the outlet box.

Preparation

• Before beginning installation, make sure all parts are included using the contents diagrams.
• If any part is missing or damaged, do not attempt to assemble, install, or operate the product.
• Estimated assembly time: 30 minutes.
• Tools required for assembly (not included): Screwdriver, pliers, wire stripper, safety glasses, electrical tape, ladder, and drill.

Care and Maintenance

• Shut off the main power supply before cleaning the product or changing light bulbs. To clean, wipe with a damp cloth. Do not use abrasive cleaners or cleaners that contain alcohol.

Assembly Instructions

1. Remove the 4 screws (CC) and 4 rubber gaskets (DD) from the edge of the fixture (A). Then separate the back plate (BB) from the fixture (A).
2. Place the back plate (BB) against the wall in the direction of the back plate arrow pointing upwards. Mark the position of the screw holes through the back plate (BB) on the wall.
   • Ensure that the back plate (BB) is level.
   • Use a 15/64 inch drill bit to drill pilot holes at the locations marked and insert the wall anchors (FF).
   • Hang the back plate (BB) by the two keyhole slots in the back of the back plate. The back plate should be oriented so that the narrow portion of the keyhole faces up.
   • Screw the 2 pan head self-tapping screws (EE) through the back plate (BB) into the two wall anchors (FF).
   • Attach the back plate (BB) to the outlet box using the mounting screws supplied with the outlet box (not provided).
   • Tighten securely.
3. Strip 3/8″ of insulation from the electrical wire ends. Using wire nuts (AA), connect the WHITE fixture wire to the WHITE supply wire from the outlet box; connect the BLACK fixture wire to the
   • BLACK supply wire from the outlet box.
   • Connect the fixture ground wire and supply ground wire using a wire nut or by fastening it to the ground screw on the round mounting plate. Push all of the wire connections carefully into the outlet box.
4. Reinstall the fixture (A) to the back plate (BB) and screw back down the 4 rubber gaskets (DD) and 4 screws (CC).

FCC

This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications.  However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

THANK YOU for selecting Progress Lighting

• We can assist you with questions regarding product information, assembly, or missing parts at 800-447-0573
• 8 am-8om (Eastern). Monday-Friday
• customerservice@progresslighting.com

Documents / Resources

| PROGRESS LIGHTING Z-2030 LED Black Contemporary Medium Outdoor Light [pdf] Instruction Manual
Z-2030 LED Black Contemporary Medium Outdoor Light, Z-2030, LED Black Contemporary Medium Outdoor Light, Contemporary Medium Outdoor Light, Medium Outdoor Light, Outdoor Light, Light
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>