BN-LINK Low Profile Surge Protector 6 Outlet 1050 Joules Instruction Manual
- June 9, 2024
- BN-LINK
Table of Contents
BN-LINK Low Profile Surge Protector 6 Outlet 1050 Joules
Product Parameters
| AC Input: | 125VAC 60Hz |
|---|---|
| AC Output: | 15A 1875W |
| Power Cable Length : | 5FT |
| USB Charging Ports: | 2 USB-A +1 USB-C |
Total 3.4A
Surge Joule Rating :| 1050J
SAFETY INSTRUCTIONS
-
This product is designed for INDOOR USE ONLY. DO NOT use in wet or damp areas or outdoors at any time.
-
Use this product only with a 125 volt AC power source. Do not exceed 1875 watts and/or 15 amps maximum load.
-
If this unit has a circuit breaker and the circuit breaker “trips” due to a power overload, do the following:
a) Unplug the multi-outlet strip from the power source.
b) Turn the power switch of each piece of connected equipment to the “off” position.
c) Unplug and remove all equipment, appliances and apparatus connected to this product.
d) Wait a few minutes and then reset the circuit breaker by pushing in the button or by turning switch on the multi-outlet strip “off” and then “reset “.
e) Plug the multi-outlet strip back into the power source.
f) Plug each piece of equipment back into the multi-outlet strip taking care not to exceed maximum wattage and amperage load. -
Before each use, make sure that the power cord is uncoiled and knot-free when in use to avoid potential over-heating of the cord and unit.
-
Always use the finger grip on the plug to remove from wall receptacle. Never pull the plug out by pulling on the cord.
-
Never open the case or housing. There are no user serviceable parts inside and opening the case renders any warranty null and void.
WARNING! Failure to comply with the following may result in damage or
injury.
All warranties contained herein are null and void if power strip is used in
violation of any of the following conditions:
- Do not use in receptacles that are not properly ground
- Do not “daisy-chain” power strips, wall taps or surge protectors in serial fashion.
- Do not plug power strip or wall tap into an extension cord.
- Do not plug extension cords into power strip or wall tap.
- Do not use power strip or wall tap in conjunction with a UPS (uninterruptible power supply).
- Do not use power strip or wall tap with three-to-two-prong adapters.
- Do not plug heaters or heat producing devices such as coffee makers, toasters, clothes irons, etc. into the power strip or wall tap.
- Do not use with generators.
- Do not use with sump pumps.
- Do not use with water-related devices.
- Do not use with life support devices.
- Do not use with medical devices.
- Do not use with cars or motorcycles.
- Do not use with golf-cart battery chargers.
- Do not use with aquariums.
THIS IS NOT A SURGE PROTECTOR
FCC REGULATORY STATEMENT
WARNING: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user authority to operate
the equipment.
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Notes: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
IC REGULATORY STATEMENT
Under Industry Canada regulations, this radio transmitter may only operate
using an antenna of a type and maximum (or lesser) gain approved for the
transmitter by Industry Canada. To reduce potential radio interference to
other users, the antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r.p.) is not more than that
necessary for successful communication.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
BN-LINK INC.
12991 Leffingwell Avenue, Santa Fe Springs
Customer Service Assistance: 1.909.592.1881
E- mail : Support@bn-link.com
http://www.bn-link.com
Hours: 9AM – 5PM PST, Mon – Fri
Designed in California Made in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>