NXP MC13234 Connectivity Test Demo User Guide
- June 9, 2024
- NXP
Table of Contents
NXP MC13234 Connectivity Test Demo
Get to Know the MC13234
In this quick start guide, you will learn how to set up the MC13234 transceiver with the REM board right out of the box. The MC13234 comes pre- programmed with the connectivity test demo, which allows you to execute basic radio functionality and monitor it with a PC through a serial connection.
Kit Contents
- MC13234 transceiver
- 1323x-MRB (modular reference board)
- 1323x-REM (remote extender motherboard)
- BeeKit wireless connectivity toolkit
- CodeWarrior development studio
- USB multilink BDM
- USB cables
Content Descriptions
- 1323x-MRB—The 1323x-MRB contains the MC13234 integrated circuit and all necessary input/output connections. It is a self contained module in a compact reference design.
- 1323x-REM —The 1323X-REM is a remote extender.
- BeeKit Wireless Connectivity Toolkit—BeeKit is a stand-alone software application targeting Windows® operating systems and provides a GUI that users can use to create, modify, save and update wireless networking solutions. HCS08 solutions created on BeeKit are exported to the CodeWarrior Development Studio
- USB Multilink BDM—The USB multilink BDM is a debug interface which allows a PC access to the background debug mode (BDM) on the MCU.
- CodeWarrior Development Studio—The CodeWarrior Development Studio IDE integrates the development tools for the ColdFire, ColdFire+, DSC, Kinetis, Qorivva, RS08, S08 and S12Z architectures into a single product based on the Eclipse open development platform.
Step-by-Step Installation Instructions
The MC13234 comes pre-programmed with the connectivity test demo for the REM board to provide a demonstration of the MC13234 capabilities.
Run the Demo
- Connect two 1323x-MRBs to their respective REM board headers.
- Connect both boards through a USB cable to a PC.
- Power on the boards.
- Configure UART/USB virtual COM port to start a serial communication with the boards. Each board requires its own connection. In this case, we will use HyperTerminal from Windows.
- Select the corresponding COM port and ensure the settings are configured as follows for each connection:
- PressOK and press the Reset button on each board.
- You will see the Connectivity Test Demo menu.
- Press “Enter” to see available tests.
Note: At this point, you can edit different settings for the tests with the interface shortcuts as shown in the image. This quick start guide will only demonstrate how packet error rate and range tests work.
Conduct a Packet Error Rate Test
The packet error rate (PER) test is a unidirectional test that sends a number of packets from a transmitter to a receiver all on a single channel.
- Once you are in the Connectivity Test Demo menu, press “2” on both terminals to select PER test.
- From now on, one board will be used as a receiver (Rx) and the other as the transmitter (Tx).
- Receiver
- Press “R” to set the board in Rx operation.
- Press the space bar to start listening to packets.
- Terminal should display the message “PER Test Rx Running.”
- Transmitter
- Press “T” to ensure the board is in Tx operation.
- Start sending packets over the air (OTA) by selecting the number of packets to be sent.
- Once the PER test is complete, a summary of received/sent packets will be displayed. You should be able to see if packets were not received due poor signal or interference.
- Press “Enter” to go back to previous menu.
Range TConduct aest
The range test uses the link quality indicator (LQI) to monitor the variation of distance between the transmitter and the receiver during a normal transmission. LQI values range from 0 to 255.
- Once you are in the Connectivity Test Demo menu, press “3” on both terminals to select Range test.
- From now on, one board will be used as a receiver (Rx) and the other as the transmitter (Tx).
- Receiver
- Press to set the board in Rx operation.
- Press the space bar to start listening to packets.
- Terminal should display the message Range Test Rx Running.
- Transmitter
- Press to ensure the board is in Tx operation.
- Press the space bar to start sending packets over the air.
- If Rx has been started, Tx will show aPacket Dropped message for each packet sent.
- After packets are sent from transmitter, the terminal will display the packets as being received with its respective LQI value. The stronger the signal, the closer to 255 the LQI value will be.
- Press space bar to stop Tx/Rx.
- Press “Enter” to return to the previous
More Information
Detailed instructions on how to run these and other demos can be found in the SMAC for S08 demonstration application user guide (SMAC08DAUG).
Support
Visit freescale.com/support for a list of
phone numbers within your region.
Warranty
Visit freescale.com/warranty for complete
warranty information.
For more information, visit
freescale.com/mc1323x
Freescale and the Freescale logo are trademarks of Freescale Semiconductor,
Inc., Reg. U.S. Pat. & Tm. Off. All other product or service names are the
property of their respective owners. © 2013 Freescale Semiconductor, Inc.
Document Number: MC13234DSKQSG REV 0
Agile Number: 926-27873 Rev A
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>