Prestel SP-H2-14T150 HDMI 1×4 HDBaseT Splitter User Manual

: June 13, 2024
: Prestel

Table of Contents

Prestel SP-H2-14T150 HDMI 1×4 HDBaseT Splitter
Introduction
Features
Package Contents
Specifications
Operation Controls and Functions
- Transmitter
EDID Mode
ASCII Commands
Application Example
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Prestel SP-H2-14T150 HDMI 1×4 HDBaseT Splitter

Prestel-SP-H2-14T150-HDMI-1x4-HDBaseT-Splitter-product

Thank you for purchasing this product
For optimum performance and safety, please read these instructions carefully before connecting, operating, or adjusting this product. Please keep this manual for future reference.

Surge protection device recommended
This product contains sensitive electrical components that may be damaged by electrical spikes, surges, electric shocks, lightning strikes, etc. Use of surge protection systems is highly recommended in order to protect and extend the life of your equipment.

Introduction

This 18Gbps HDMI 1×4 HDBaseT Splitter can distribute 1 source signal to any 4 display devices. Support video resolution up to 4K2K@60Hz 4:4:4. It is designed with 1 HDMI loop output and 4 HDBaseT outputs. The HDMI signal transmission distance can be extended up to 120 meters at the resolution of 4K2K@60Hz, or 150 meters at 1080P@60Hz via a single CAT6/ 6a/7 cable. The product supports IR and RS-232 signal pass-through, audio extract function and advanced EDID management.

Features

HDMI 2.0b, HDCP 2.2 and HDCP 1.x compliant
Support 18Gbps video bandwidth
Support video resolution up to 4K2K@60Hz 4:4:4
Support HDR, HDR10+, HLG and Dolby vision
Support up to 7.1CH HD audio pass-through
Support digital and analog audio de-embedded output
Extend the signal transmission distance up to 120 meters at the resolution of 4K2K@60Hz, 150 meters at 1080P@60Hz via a single CAT6/6a/7 cable
Support 1 HDMI input, 1 HDMI loop output and 4 HDBaseT outputs.
IR, RS-232 routed to HDBaseT output
Advanced EDID management
Support one-way POC function (only from transmitter to receiver)
Compact design for easy and flexible installation

Package Contents

1 × 18Gbps HDMI 1×4 HDBaseT Splitter
4 × HDBaseT Receiver
5 × IR Blaster Cable (1.5 meters)
5 × 20K~60KHz IR Receiver Cable (1.5 meters)
5 × 3-pin Phoenix Connector
1 × 5-pin Phoenix Connector
10 × Mounting Ear
1 × 24V/2.7A DC Locking Power Adapter
1 × User Manual

Specifications

Technical

HDMI Compliance| HDMI 2.0b
HDCP Compliance| HDCP 2.2/1.x
Video Bandwidth| 594MHz/18Gbps
Video Resolution| Up to 4k2k@60Hz 4:4:4

Color Depth

| 8-bit,10-bit,12-bit(1080p@60Hz) 8-bit (4K2K@60Hz YUV4:4:4)

8-bit,10-bit,12-bit(4K2K@60Hz YCbCr 4:2:2/4:2:0)

Color Space| RGB 4:4:4, YCbCr 4:4:4 / 4:2:2 / 4:2:0
HDR| Support HDR, HDR10+, HLG, Dolby vision

HDMI Audio Formats

| LPCM 2.0/2.1/5.1/6.1/7.1, Dolby Digital, Dolby TrueHD, Dolby Digital Plus(DD+), DTS-ES, DTS HD Master, DTS HD-HRA, DTS-X
Coaxial Audio Formats| PCM2.0, Dolby Digital / Plus, DTS 2.0/5.1
Analog Audio Formats| PCM 2.0CH
ESD Protection| Human body model—±8kV (Air-gap discharge) &

±4kV (Contact discharge)

Connection
Input| 1×HDMI Type A (19-pin female)

Output

| 1×HDMI Type A (19-pin female） 4x HDBaseT OUT [RJ45]

1x Coaxial Audio OUT [RCA]

1x L/R Audio OUT [5-pin phoenix connector]

Control

| 1×RS-232 (3-pin phoenix connector） 1x EDID DIP switch [5-pin]

1x IR IN [3.5mm Stereo Mini-jack] 1x IR OUT [3.5mm Stereo Mini-jack]

Mechanical

(US/EU standards, CE/FCC/UL certified)

Power Consumption| 35W
Operation

Temperature

| 0°C ~ 40°C / 32°F ~ 104°F
Storage Temperature| -20°C ~ 60°C / -4°F ~ 140°F
Relative Humidity| 20~90% RH (non-condensing)

Operation Controls and Functions

Transmitter

Front Panel

Prestel-SP-H2-14T150-HDMI-1x4-HDBaseT-Splitter-fig-1

No.	Name	Function Description
1	POWER LED	When the device is powered on, the red power LED will

be on.

2| IN LED| When the HDMI IN port connects an active source device,

the green LED will be on.

3| LOOP LED| When the HDMI LOOP OUT port connects an active display device, the green LED will be on.
4| OUT(1~4) LED| When the HDBT OUTPUT port connects an HDBaseT Receiver, the corresponding green OUT LED will be on.

Rear Panel

Prestel-SP-H2-14T150-HDMI-1x4-HDBaseT-Splitter-fig-2

No.	Name	Function Description

1

| ****

RS-232

| Connect to a PC or control system via a 3-pin phoenix connector cable for three functions:

1, Firmware update;

2, Control the Splitter via RS-232 commands;

3, RS-232 signal pass-through (from transmitter to receiver or from receiver to transmitter).

switch

| Used to set EDID mode. Please refer to Section “6. EDID Mode” for details.

7

| ****

HDMI port

| IN: HDMI input port, connect to HDMI source device such as DVD or set-top box with an HDMI cable.
LOOP OUT: HDMI loop output port, connect to the HDMI display device such as TV or Monitor with an HDMI cable.
8| HDBT OUTPUT

port (1~4)

| Connect to the HDBT IN port of the HDBaseT receiver with a CAT cable.

9

| ****

Connection Signal Indicator lamp (Green)

| ▪ Illuminating: Transmitter and Receiver are in good connection status.

▪ Flashing: Transmitter and Receiver are in poor

connection status.

▪ Dark: Transmitter and Receiver are not connected.

10

| Data Signal Indicator lamp (Orange)| ▪ Illuminating: HDMI signal with HDCP.

▪ Flashing: HDMI signal without HDCP.

▪ Dark: No HDMI signal.

---|---|---

11

| ****

DC 24V

| Plug the DC 24V power supply into the unit and connect the adaptor to an AC outlet. ( Note: The transmitter can power the receiver via a CAT cable.)

HDBaseT Receiver

Prestel-SP-H2-14T150-HDMI-1x4-HDBaseT-Splitter-fig-3

No.	Name	Function Description
1	Power Indicator	When the receiver is powered on, the power indicator will

be on.
2| SERVICE port| Used for firmware update.

3

| ****

DC 24V

| Plug DC 24V/1A power supply into the unit and connect the adapter to an AC outlet.

( Note: The HDBaseT receiver also can be powered by the

transmitter via a CAT cable.)

4| HDBT IN| Connect to the HDBT OUTPUT port on the transmitter with a CAT cable.

5

| ****

Connection Signal Indicator lamp (Green)

| ▪ Illuminating: Transmitter and Receiver are in good connection status.

▪ Flashing: Transmitter and Receiver are in poor

connection status.

▪ Dark: Transmitter and Receiver are not connected.

6

| Data Signal Indicator lamp

(Orange)

| ▪ Illuminating: HDMI signal with HDCP.

▪ Flashing: HDMI signal without HDCP.

▪ Dark: No HDMI signal.

7| HDMI OUT| HDMI output port, connect to HDMI display device such as TV or Projector with an HDMI cable.
8| AUDIO OUT| Audio output port, connect to amplifer or speaker.
---|---|---
9| IR IN| Connect to the IR Receiver cable. The IR signal will send to the IR OUT port of the transmitter.
10| IR OUT| Connect to the IR blaster cable, the IR signal is from IR

IN port of the transmitter.

11

|

RS-232

| 3-pin Phoenix connector for RS-232 command transmission. The RS-232 command will pass-through

from transmitter to receiver or from receiver to transmitter

IR Pin Definition

Prestel-SP-H2-14T150-HDMI-1x4-HDBaseT-Splitter-fig-4

Note: When the angle between the IR receiver and the remote control is ± 45 °, the transmission distance is 0-5 meters; when the angle between the IR receiver and the remote control is ± 90 °, the transmission distance is 0-8 meters.

EDID Mode

The defined EDID setting list of the product is shown as below:

EDID Mode	EDID Description
11111	1080P, Stereo Audio 2.0
11110	1080P, Dolby/DTS 5.1
11101	1080P, HD Audio 7.1
11100	1080I, Stereo Audio 2.0
11011	1080I, Dolby/DTS 5.1
11010	1080I, HD Audio 7.1
11001	1080P 3D, Stereo Audio 2.0
11000	1080P 3D, Dolby/DTS 5.1
10111	1080P 3D, HD Audio 7.1
10110	4K2K30Hz_444, Stereo Audio 2.0
10101	4K2K30Hz_444, Dolby/DTS 5.1
10100	4K2K30Hz_444, HD Audio 7.1
10011	4K2K60Hz_420, Stereo Audio 2.0
10010	4K2K60Hz_420, Dolby/DTS 5.1
10001	4K2K60Hz_420, HD Audio 7.1
10000	4K2K60Hz_444, Stereo Audio 2.0
01111	4K2K60Hz_444, Dolby/DTS 5.1
01110	4K2K60Hz_444, HD Audio 7.1
01101	4K2K60Hz_444, Stereo Audio 2.0 HDR
01100	4K2K60Hz_444, Dolby/DTS 5.1 HDR
01011	4K2K60Hz_444, HD Audio 7.1HDR
01010	COPY_FROM_LOOP OUT
01001	COPY_FROM_HDBT OUT1
01000	COPY_FROM_HDBT OUT2
00111	COPY_FROM_HDBT OUT3
00110	COPY_FROM_HDBT OUT4
00101	1080P, Stereo Audio 2.0
00100	1080P, Stereo Audio 2.0
00011	1080P, Stereo Audio 2.0
00010	1080P, Stereo Audio 2.0
00001	1080P, Stereo Audio 2.0
00000	PC control mode

ASCII Commands

The product also supports ASCII command control. Connect the RS-232 port of the product to a PC with a 3-pin phoenix connector cable. Then, open a Serial Command tool on PC to send ASCII commands to control the product. The ASCII command list about the product is shown as below.

ASCII Commands

Serial port protocol. Baud rate: 115200, Data bits: 8bit, Stop bits:1, Check bit: 0
x – Parameter 1 y – Parameter 2

! – Delimiter

Command Code| Function Description| Example| Feedback| Default Setting
Power

s power z!

|

Power on/off the device,z=0~1 (z=0 power off, z=1 power on)

|

s power 1!

| Power on

System Initializing… Initialization Finished! FW version x.xx.xx

|

power on

r power!| Get current power state| r power!| power on/power off|

s reboot!

|

Reboot the device

|

s reboot!

| Reboot…

System Initializing… Initialization Finished! FW version x.xx.xx

r status!

|

Get device current status

|

r status!

| Get the unit all status: power,

in/out connection,

edid mode

r link out y!

| Get the connection status of the y output port, y=0~5(0=all, 1~4=HDBT 1~4, 5 = loop out)|

r link out 1!

| hdmi loop out:

connect

hdbt output 1: connect

|

s reset!

|

Reset to factory defaults

|

s reset!

| Reset to factory defaults

System Initializing… Initialization Finished! FW version x.xx.xx

|
Command Code| Function Description| Example| Feedback| Default Setting
---|---|---|---|---
Output Setting

s hdmi stream z!

| Set hdmi loop output stream on/off z=0~1(0:disable,1:enable)|

s hdmi stream 1 !

| Enable hdmi loop out stream

Disable hdmi loop out

stream

|

enable

s hdmi hdcp z!

| Set hdmi loop output hdcp on/ off

z=0~1(0:disable,1:enable)

|

s hdmi hdcp 1!

| Enable hdmi loop out HDCP

Disable hdmi loop out

HDCP

|

enable

s hdbt y hdcp z!

|

Set hdbt output y hdcp on/off, y=0~4(0=all) z=0~1(0:disable, 1:enable)

|

s hdbt 1 hdcp 1 !

s hdbt 0 hdcp 1 !

| Enable heat output 1

HDCP

Disable heat output 1 HDCP

Enable habit all outputs hdcp Disable hdbt all

outputs HDCP

|

enable

| | | Enable heat output 1|

s hdbt y stream z!

|

Set hdbt output y stream on/ off, y=0~4(0=all) z=0~1 (0:disable,1:enable)

| s hdbt 1 stream 1 !

s hdbt 0 stream 1 !

| stream

Disable heat output 1 stream

Enable habit all outputs stream

Disable edit all

|

enable

| | | outputs stream|
r hdmi stream!| Get hdmi loop out stream status| r hdmi stream!| Enable HDMI output stream|
r hdmi hdcp!| Get hdmi loop out hdcp status| r hdmi hdcp!| Enable hdmi output HDCP|
r hdbt y hdcp!| Get debt output y hdcp status, y=0~4(0=all)| r hdbt 1 hdcp!| Enable heat output 1 HDCP|
r hdbt stream!| Get debt output y stream status, y=0~4(0=all)| r hdbt 1 stream!| Enable heat output 1 stream|
Command Code| Function Description| Example| Feedback| Default Setting
---|---|---|---|---
EDID Setting
| Set input EDID from default EDID z, z=1~27

1, 1080p,Stereo Audio 2.0

2, 1080p, Dolby/DTS 5.1

3, 1080p,HD Audio 7.1

4, 1080i,Stereo Audio 2.0

5, 1080i, Dolby/DTS 5.1

6, 1080i,HD Audio 7.1

7, 3D,Stereo Audio 2.0

8, 3D, Dolby/DTS 5.1

9, 3D,HD Audio 7.1

10, 4K2K30_444,

Stereo Audio 2.0

11, 4K2K30_444, Dolby/DTS 5.1