Spa Electrics GKRX Multiplus-LED Variable Voltage Light User Guide
- June 8, 2024
- Spa Electrics
Table of Contents
- READ FIRST
- WIRING INFORMATION
- MANUAL MODE USER INSTRUCTIONS
- QUICK SETUP iRIS
- QUICK SETUP CONNECT 10
- QUICK SETUP AQUALINK INTELLITOUCH/EASYTOUCH
- QUICK SETUP AQUALINK RS/TRI
- MANUAL MULTI PLUS SETUP
- VERSION IDENTIFICATION
- OPERATING MODE COLOURS
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Spa Electrics GKRX Multiplus-LED Variable Voltage Light
READ FIRST
The MULTI-PLUS light has 7 inbuilt modes of operation for use on a variety of different control systems or installation types.
When you first install your MULTI-PLUS light it will operate in the default, ‘Manual’ mode for use with a wall switch. see MANUAL MODE USER INSTRUCTIONS
When connecting the light to a 3rd party pool controller you will need to change the operating mode of the light, for an expedited setup see QUICK SETUP guides for your corresponding pool controller.
If installing MULTI-PLUS lights with legacy Multi Colour and P-Type lights, see MANUAL MULTI-PLUS SETUP
WIRING INFORMATION
MANUAL MODE OPERATION (SYNCHRONISED POOL & SPA)
SYNCHRONIZED INSTALLATION
When installing multiple lights, to ensure synchronization and ease of
operation ALL Lights must operate from a single switch.
CONNECTING TO POOL/LIGHTING CONTROLLER
MANUAL MODE USER INSTRUCTIONS
When installing multiple lights, to ensure synchronization and ease of operation ALL Lights must operate from a single switch.
OPERATING INSTRUCTIONS
-
To change the color of the light, simply turn your light OFF for 2 seconds and then turn it back ON. This will signal the light to proceed to the next colour in sequence.
To select a desired colour, simply step through the colours until you find your desired selection.
Refer to OPERATING MODE COLOURS for available colours. -
Your lights will automatically save your selected colour once the power has been turned OFF for more than 1 minute. So the next time the lights are used, they will illuminate on the last colour operated.
-
To reset or ‘synchronize’ your lights; with the power turned ON, turn the power OFF/ON once rapidly. This will RESET your lights to WHITE
SYNCHRONIZED INSTALLATION
When installing multiple lights, to ensure synchronization and ease of
operation ALL Lights must operate from a single switch.
QUICK SETUP iRIS
The iRIS lighting controller has a QUICK SETUP feature to program the MULTI PLUS lights for iRIS operation.
STEP 1
Ensure the lights have been OFF for a minimum of 30 seconds, then turn the
system ON using the iRIS handset.
STEP 2
Press the following static colours in order with a 1 second pause between
each press.
1. WHITE
2. RED
3. GREEN
If performed correctly, the lights will illuminate GREEN. Confirm correct operation by selecting a different colour using the iRIS handset.
QUICK SETUP CONNECT 10
NOTE: QUICK SETUP – CONNECT 10 is only available with MULTI PLUS lights produced after 21/01/2018 – see “VERSION IDENTIFICATION” for details
STAGE 1 – POOL CONTROLLER SETUP
When connecting the Multi Plus light to a Connect 10 pool controller please ensure the system is fully installed and you have completed all the relevant steps in the controller setup menu to operate the lights correctly
During pool controller setup ensure that the “Zone supports Multi-Colour
lighting” checkbox is selected and that the “SLX LIGHT” light model is
selected.
During channel setup select “Yes” when prompted “Is this a multi-colour
capable light?”
(For more information on this please refer to the pool controller installation
manual).
NOTE: Some older pool controllers may not support these models. Please
contact Spa Electrics assistance.
STAGE 2 – POOL LIGHT SETUP
Step 1 – Ensure the light has been turned off for at least 30 seconds
Step 2 – Turn the light ON using the Connect 10 Touchscreen
Step 3 – Press the SYNC button,
once the Connect 10 and Multi Plus Light have finished communicating the Multi
Plus light can be operated using the Connect 10 pool controller
(This step must be performed within 30 second of step 2)
QUICK SETUP AQUALINK INTELLITOUCH/EASYTOUCH
NOTE: QUICK SETUP – INTELLITOUCH/EASYTOUCH is only available with MULTI PLUS lights produced after 21/01/2018 – see “VERSION IDENTIFICATION” for details
STAGE 1 – POOL CONTROLLER SETUP
When connecting the Multi Plus light to an Intelitouch or Easytouch pool controller please ensure the system is fully installed and you have completed all the relevant steps in the controller setup menu to operate the lights correctly
During pool controller setup ensure that the light model selected is INTELLIBRITE LIGHT
(For more information on this please refer to the pool controller installation
manual).
NOTE: Some older pool controllers may not support these models.
Please contact Spa Electrics assistance.
STAGE 2 – POOL LIGHT SETUP
Step 1 – Ensure the light has been turned off for at least 30 seconds
Step 2 – Navigate to the “Lights/Colors” menu on the pool controller
Handset or Control Panel.
Step 3 – Select MAGENTA in the colour menu , and wait until the relays
finish operating.
Step 4 – Select GREEN in the colour menu , and wait until the relays
finish operating.
Step 5 – Select BLUE in the colour menu , and wait until the relays
finish operating.
Step 6 – After 3 seconds the Multi Plus light will turn itself off for 1.5
seconds and turn on BLUE.
This will indicate that the mode setup has been completed correctly
INTELLITOUCH/EASY TOUCH CONTROLLERS
AQUALINK TRI CONTROLLERS
QUICK SETUP AQUALINK RS/TRI
NOTE: QUICK SETUP – AQUALINK RS/TRI is only available with MULTI PLUS lights produced after 21/01/2018 – see “VERSION IDENTIFICATION” for details
STAGE 1 – POOL CONTROLLER SETUP
When connecting the Multi Plus light to an Aqualink RS/Z4 pool controller please ensure the system is fully installed and you have completed all the relevant steps in the controller setup menu to operate the lights correctly
During pool controller setup ensure that the light model selected is JANDY LED LIGHT
(For more information on this please refer to the pool controller installation
manual).
NOTE: Some older pool controllers may not support these models. Please
contact the controller manufacturer for upgrade assistance.
STAGE 2 – POOL LIGHT SETUP
Step 1 – Ensure the light has been turned off for at least 30 seconds
Step 2 – From the home screen on the control panel, Select “Equipment ON/OFF”.
Step 3 – Select the channel for the lights, each channel will need to be
setup individually.
Step 4 – Select DISCO TECH in the “Set Color” menu.
Step 5 – After the controller finishes power cycling, the Multi Plus light
will turn itself off for 1.5 seconds and turn on DISCO TECH. This will
indicate that the mode setup has been completed correctly.
MANUAL MULTI PLUS SETUP
Manual Multi Plus Setup is for installations where the use of a quick setup is not possible or a new MULTI-PLUS light is being installed with an existing Multi Colour or P-Type light.
The MULTI-PLUS light has 7 inbuilt modes of operation for use on a variety of different control systems or installation types.
When you first install your MULTI-PLUS light it will operate in the default, ‘Manual’ mode for use with a wall switch. In order to connect the light to a 3rd party pool controller OR change to a different operating mode please follow the below steps
STEP 1 – POOL CONTROLLER SETUP
If connecting to a pool controller, please ensure the system is fully installed and you have completed all the relevant steps in the controller setup menu to operate the lights correctly.
During pool controller setup you will be prompted to select which light model is installed. Please use the below table to select the appropriate light for your pool controller type.
(For more information on this please refer to the pool controller installation manual).
POOL CONTROLLER | SELECT LIGHT MODEL |
---|---|
Astral Connect 10 (2016 to current) | SLX Light |
Jandy Aqualink RS (F/W Rev. ‘R’- Current) | Jandy |
Zodiac Aqualink TRI | Jandy |
Pentair EasyTouch | Intellibrite Light |
Pentair IntelliTouch | Intellibrite Light |
Hayward Omnilogic | (UCL)Universal Colorlogic |
NOTE: Some older pool controllers may not support these models. Please contact the controller manufacturer for upgrade assistance.
STEP 2 – LIGHT SETUP
IMPORTANT : Ensure Lights have been off for at least 30 seconds prior to performing this step
NOTE: This step can either be performed via a wall switch OR via the
controller panel/Mobile App.
NOTE: If ALL Lights connected to circuit are NOT continuously flashing RED, please turn Lights OFF & wait 30 seconds before repeating STEP 2
STEP 3 – SELECTING OPERATING MODE
After accessing SETUP MODE (STEP 2) the lights will FLASH RED continuously.
This is MODE 1 (Manual mode)
Use the below process to change the operating mode to correspond to the
required controller or operating type below.
IMPORTANT: Once desired mode is reached (i.e. “Flashing Green – iRIS Mode) leave power turned ON and continue to STEP 4
‘FLASHING’ COLOUR| CONTROLLER / OPERATING TYPE| **LIGHT MODEL
SELECTED**
---|---|---
1. RED| Manual Mode (wall switch)| –
2. GREEN| Spa Electrics iRIS Controller| –
3. MAGENTA| Astral Connect 10 (2016 to current)| SLX Light
4. WHITE| Jandy Aqualink RS (F/W Rev. ‘R’-Current)| Intellibrite Light
| Zodiac Aqualink TRI| Intellibrite Light
| Pentair EasyTouch| Intellibrite Light
| Pentair IntelliTouch| Intellibrite Light
5. BLUE| RGB MULTI Mode (wall switch)|
–
6. YELLOW| Hayward Omnilogic| Universal Colorlogic
7. PINK| P-TYPE Mode* (Legacy)| Intellibrite Light
8. AQUA| Aqualink RS/Z4| Jandy
*Light Model Selected:
This indicates the model of light to be selected in the Pool Controller setup
menu.
Refer to STEP 1 on the previous page, for more information or please contact
Spa Electrics. (03) 9793 2299
*RGB MULTI Mode:
This mode allows the MULTI PLUS light to operate in the standard MULTI-Colour
mode. This mode should only be used when operating a MULTI PLUS light from a
wall switch with a standard Spa Electrics MULTI-Colour light. For more
information please contact Spa Electrics.
*P-TYPE Mode:
This mode allows the MULTI PLUS light to operate in the RGB P-Type Colour
mode. This mode should only be used when operating a MULTI PLUS light in
conjunction with an existing Spa Electrics P-Type light. For more information
please contact Spa Electrics.
STEP 4 – SAVING OPERATING MODE
Once the desired operating mode is selected follow these steps to save the
selection.
Important
You must wait at least 30 Seconds prior to turning the system back ON or
selection process will fail and setup will need to be restarted.
STEP 5 – CONFIRM OPERATION
Your setup should now be complete. To confirm the system is working correctly, select a colour via the controller or wall switch (depending on operating mode selected) and check to ensure all lights are synchronised and the correct colour is displayed.
Refer to OPERATING MODE COLOURS for available colours.
VERSION IDENTIFICATION
New Features such as QUICK SETUP for selected pool controllers are not available in order versions of the MULTI PLUS lights. These features are only available in MULTI PLUS lights produced after 21/01/18.
The Production Date of your light can be located in the lower right corner of the product label adhered to the light’s packaging.
If the light has been removed from it’s packaging, you can identify if the QUICK SETUP features are available to your MULTI PLUS light, by comparing the serial number attached to the light to the table below:
LIGHT SERIES | CONNECT 10, INTELLITOUCH, EASYTOUCH, OMNILOGIC | AQUALINK RS/TRI |
---|---|---|
WN | WN-27964 and Greater | WN-43973 and Greater |
GK | GK-103398 and Greater | GK-106189 and Greater |
EM | EM-78510 and Greater | EM-96899 and Greater |
WNRX | WX-07079 and Greater | WX-11176 and Greater |
GKRX | GX-32314 and Greater | GX-52027 and Greater |
EMRX | EX-02348 and Greater | EX-03847 and Greater |
Need help identifying the version of your MULTI PLUS light?
please contact Spa Electrics. (03) 9793 2299 for assistance
OPERATING MODE COLOURS
MANUAL MODE (DEFAULT)
1| WHITE 4000K
2| AQUA
3| BLUE
4| MAGENTA
5| RED
6| LIME
7| GREEN
8| OCEANIC VIEWS
9| TRANSCENDENCE
10| OUTBACK AUSTRALIA
11| SPRING EQUINOX
iRIS MODE
1| WHITE 4000K
2| AQUA
3| BLUE
4| MAGENTA
5| RED
6| LIME
7| GREEN
8| OCEANIC VIEWS
9| TRANSCENDENCE
10| OUTBACK AUSTRALIA
11| SPRING EQUINOX
CONNECT 10 MODE
1| BLUE
2| MAGENTA
3| RED
4| ORANGE
5| GREEN
6| AQUA
7| WHITE
8| CUSTOMISED COLOUR
9| RAINBOW PATTERN
10| OCEAN PATTERN
UNIVERSAL COLORLOGIC MODE
1| VOODOO LOUNGE
2| DEEP BLUE SEA
3| ROYAL BLUE
4| AFTERNOON SKIES
5| AQUA GREEN
6| EMERALD
7| CLOUD WHITE
8| WARM RED
9| FLAMINGO
10| VIVID VIOLET
11| SANGRIA
12| TWILIGHT
13| TRANQUILITY
14| GEMSTONE
15| USA
16| MARDI GRAS
17| COOL CABARET
INTELLIBRITE MODE
1| SAM
2| PARTY
3| ROMANCE
4| CARIBBEAN
5| AMERICAN
6| CALIFORNIA SUNSET
7| ROYAL
8| BLUE
9| GREEN
10| RED
11| WHITE
JANDY MODE
1| ALPHA WHITE
2| SKY BLUE
3| COBALT BLUE
4| CARIBBEAN BLUE
5| SPRING GREEN
6| EMERALD GREEN
7| EMERALD ROSE
8| MAGENTA
9| VIOLET
10| SLOW COLOR SPLASH
11| FAST COLOR SPLASH
12| AMERICA THE BEAUTIFUL
13| FAT TUESDAY
14| DISCO TECH
P-TYPE MODE
1| SAM
2| PARTY
3| ROMANCE
4| CARIBBEAN
5| AMERICAN
6| CALIFORNIA SUNSET
7| ROYAL
8| BLUE
9| GREEN
10| RED
11| WHITE
12| MAGENTA
*STANDARD MULTI MODE**
1| BLUE
2| MAGENTA
3| RED
4| LIME
5| GREEN
6| AQUA
7| WHITE 1
8| WHITE 2
9| SLOW COLOUR BLEND
10| FAST COLOUR CHANGE
*Standard MULTI Mode:
This mode allows the MULTI PLUS light to operate in the standard MULTI-Colour
mode. This mode should only be used when operating a MULTI PLUS light from a
wall switch or RM-2, in conjunction with a standard Spa Electrics MULTI-Colour
light.
Connect 10® is a registered trademark of AstralPool Australia and/or its
affiliated companies in the United states or other countries.
For more information please contact Spa Electrics. (03) 9793 2299
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>