SmartCode 10 Touchpad Electronic Beadbolt GED1700 User Manual

June 8, 2024
Weiser

WEISER

Smartcode logo

**64002-002,Rev 02 , GED1700**

``Installation and User Guide

Weiser

USA: 1-800-677-5625
Canada: 1-800-501-9471
www.weiserlock.com

Smartcode - Parts in the box

Prepare the door and check dimensions

If drilling a new door, use the supplied template and the complete door drilling instructions available at www.weiserlock.com/doorprep.

**A** Measure to confirm that the hole in the door is either 2-1/8″ (54 mm) or 1-1/2″ (38 mm).

Note: Additional door preparation may be required for doors with 1-1/2″ (38 mm) holes. Consult the deadbolt drilling instructions at www.weiserlock.com/doorprep.

**B** Measure to confirm that the backset is either 2-3/8″ or 2-3/4″ (60 or 70 mm).

**C** Measure to confirm that the hole in the door edge is 1″ (25 mm).

**D** Measure to confirm that the door is between 1-3/8″ and 2″ (35 mm and 51 mm) thick.

2  Install the latch and strike

   GED1700 - Install the latch and strike

Install the latch and strike``

3  Install the exterior keypad

**A ** What is the diameter of the hole in the door?

Install the exterior keypad A

**B ** Locate screws for step 3C and keep them within reach.

Install the exterior keypad B

**C ** Install exterior keypad and mounting plate.

Install the exterior keypad C

4  Install the interior assembly

**A **  Remove battery cover and battery pack from interior assembly.

Install the interior assembly A

**B **  Install interior assembly onto mounting plate.

Install the interior assembly B

5  Install the batteries and perform the door handing process

This step will teach your lock the orientation of your door and is crucial to lock operation.

**A**  Install 4 AA batteries in battery pack.

  Press and HOLD the Lock button while installing battery pack. Hold button until the latch bolt starts moving on its own.

**C**   Did the latch bolt retract and extend on its own when the battery pack was installed?

Install the batteries and perform the door handing process
C

6  Add user codes (16 max)

Programming Timeout
During programming, if no button is pressed for five seconds, the system will time out (indicated by three beeps and a red flashing keypad), and you will need to restart the procedure.

**A**  Make sure the door is open. Press the Program button once.

**B**  Enter user code. A total of 16 user codes may be programmed.

**C**  Press Lock button once.

**D**  What lights and sounds does the lock produce?

Add user codes D

*Beeping sound will only be heard if switch #3 (on the lock interior) is in the on positon. See “Switches and Status LED Colors” on page 4.

Mastercode
For enhanced security, a mastercode may be used when adding and deleting user codes. For more information about the mastercode, download the Programming and Troubleshooting Guide on the SmartCode 10 page at www.weiserlock.com.

7   Test the lock (review normal operation)

Confirm that the code(s) added in previous step can unlock the door.

Test the lock

8   Re-key the lock (if needed) and install the battery cover

**A**  Re-key the lock (if needed).

Re-key the lock \(if needed\) and install the battery cover
A

**B**  Install the battery cover.

Reference Guide

SmartCode at a Glance

SmartCode at a Glance

Switches and Status LED colors

 System Alerts

System Alerts

Switches and Status LED colors

Troubleshooting

A complete Programming and Troubleshooting Guide is available on the SmartCode 10 page at www.weiserlock.com.

Deleting a single user code

Note: All codes may be deleted at once if the mastercode is enabled. For more information about the mastercode, consult the online Programming and Troubleshooting Guide.

Deleting a single user code

If no button is pressed for five seconds, the system will time out, and you will need to restart the procedure.

Factory Reset

A factory reset will delete all codes associated with the lock.

Factory Reset

Important Safeguards

  1. 1. Read all instructions in their entirety.
  2.  Familiarize yourself with all warning and caution statements.
  3.  Remind all family members of safety precautions.
  4.  Protect your user codes and mastercode.
  5.  Dispose of used batteries according to local laws and regulations. CAUTION: Prevent unauthorized entry. Since anyone with access to the back panel can change the user codes, you must restrict access to the back panel and routinely check the user codes to ensure they have not been altered without your knowledge. The use of a master code can help protect your system’s settings. WARNING: This Manufacturer advises that no lock can provide complete security by itself. This lock may be defeated by forcible or technical means or evaded by entry elsewhere on the property. No lock can substitute for caution, awareness of your environment, and common sense. Builder’s hardware is available in multiple performance grades to suit the application. In order to enhance security and reduce risk, you should consult a qualified locksmith or other security professional.

SmartCode 10 Touchpad Electronic Beadbolt GED1700 User Manual – Optimized PDF
SmartCode 10 Touchpad Electronic Beadbolt GED1700 User Manual – Original PDF

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals