Halo Wi-Fi Touchscreen Smart Lock GED2500 User Manual
- June 8, 2024
- Weiser
Table of Contents
Installation and User Guide
Parts List
Prepare the door and check dimensions
Make sure your door is compatible. If you have a standard
deadbolt mounted
separately from the handle below it, your door is compatible.
Remove your existing deadbolt
from your door.
Measure to confirm that the hole in the door is either
2-1/8″ (54 mm) or 1-1/2″ (38 mm).
Note: Additional door preparation may be required for doors with
1-1/2″ (38 mm) holes. Consult the deadbolt drilling instructions at
weiserlock.com/doorprep
Measure to confirm that the backset is
either 2-3/8″ or 2-3/4″ (60 or 70 mm).
Measure to confirm that the hole
in the door edge is 1″ (25 mm).
Measure to confirm that the door is
between
1-3/8″ and 2″ (35 mm and 51 mm) thick.
Install the latch and strike
Is the door edge chiseled?
Hold the latch in front of the door hole, with the latch
face flush against the door edge.
Is the D-shaped hole centered in the door hole?
Which latch are you installing?
Install the strike on the door frame.
Make sure the hole in the door frame is drilled a
minimum of 1″ (25 mm) deep.
Install the exterior keypad
What is the diameter of the hole in the door?
Locate the screws for step 3D and keep them within reach.
Remove the mounting plate from the interior assembly.
Install the exterior A keypad and mounting plate.
Install the interior assembly
Ensure the turnpiece shaft is pointing up, and remove the
interior cover and
battery pack from the interior assembly
Install the interior assembly onto the mounting plate.
Install the batteries and perform the door handing process
This step will teach your lock the orientation of your door and is crucial to lock operation.
Install 4 AA batteries in the battery pack.
With the door open, install the battery
pack to initiate auto-handing.
After a few seconds, the latch bolt will retract and extend on
its own to learn the orientation of the door. This is called the
door handing process, and it is crucial to lock operation.
Test the lock and check door alignment
With the door open, insert the key to
extend the latch. Ensure that the latch
extends smoothly.
Turn the key 180° to retract the latch.
Ensure that the latch
retracts smoothly.
Close the door. Insert and rotate
the key to lock the door. Ensure
that the door locks smoothly.
Turn the key 180° to retract the latch.
Ensure that the door
unlocks smoothly.
If your door does not lock and unlock smoothly, make sure you replaced your
previous latch and strike with those supplied in the box.
If you still experience locking errors, call Weiser Support to order a Warped
Door Service Kit.
Weiser Support: 1-800-501-9471
Install the interior cover
Important Information about the interior cover
The window on
the interior cover
is unlocked by
default for easier
access to the
battery pack
and buttons
For additional
security, you
may choose to
lock the window
by installing the
security screw.
When the window
is locked, you will
need to remove
the entire interior
cover and screws to
access the battery
pack and buttons.
Cover Installation
Install cover.
Note: You may
need to rotate
the turn piece
to align with the
turn piece shaft
Install
screws.
Battery Pack Access
If the window is
unlocked, slide
up the window
to access the
battery pack.
If the window
is locked,
remove the
interior cover
and screws
to access the
battery pack.
Download the app and create an account
The Weiser app is needed to use this lock. If
this lock was professionally installed (or installed
by someone other than the homeowner), make
sure this step is performed by the homeowner.
Download the
Weiser app by scanning
the QR code or visiting
www.weiserlock.com/app
on your smartphone
Create your account and follow the setup
instructions in the Weiser app.
Reference Guide
SmartCode at a Glance
Status LED colors
These features can be adjusted in some smart home apps.
System Alerts
*Beeping sounds will only be heard if Lock Sounds have not been disabled in the app.
Manual Door Handing
If needed, the door handing process can be initiated manually. This is useful
if the lock is being
moved to a different door.
-
Remove battery pack.
-
Press and HOLD
the Program button
while reinserting
the battery pack.
Release the
Program button
after 3 seconds.
The status LED will
flash red and green. -
Press the Program button once more.
-
The latch bolt will extend and retract to
learn the orientation of the door. The LED
will flash green if handing is successful
or red if handing is unsuccessful.
Network Reset
Network Reset will delete all Wi-Fi settings, Bluetooth pairings, user
associations, and remove the lock from the account.
-
Press and HOLD
“A” for 10 seconds.
You will hear 1 short
beep and see an
amber LED.
Note: After 3
seconds, you will
hear 1 short beep
and see a blue
LED. You should
continue to hold “A”
to enter network
reset mode. -
Release “A.”
You will see a
blinking amber
LED to indicate
it is in network
reset mode. -
If successful, you will hear 1 long
beep and see a green LED. If
unsuccessful, you will hear 5 rapid
beeps and see a blinking red LED. If
unsuccessful, repeat from step 1. -
Press and release the
Program button to
confirm network reset.
The Program button must be
pressed within 10 seconds of
releasing “A” or the function
will time out.
System Reset
System Reset will delete all access codes and lock settings including
lock handing. The lock will run the handing process at the end of the
System Reset.
-
Press “A” 10times. You will
hear 1 shortbeep and see a
blinking amber
LED to indicate
it is in system
reset mode. -
Press and release
the Program
button to confirm
system reset.
3 If successful, you will hear 1
Factory Reset
Factory Reset will delete all Wi-Fi settings, Bluetooth pairings, user
associations, remove the lock from the account, and reset all lock
settings including handing.
-
Remove
battery pack. -
Press and HOLD
the Program button while reinserting
the battery pack.
Keep holding
the button for
30 seconds until
the lock beeps
and the status
LED flashes red. -
Press the Program button
once more. The LED will
flash green and red, and
the auto-handing process
will begin. -
The latch will retract and
extend to learn the orientation
of the door. The LED will
flash green if auto-handing
is successful or red if autohanding
is unsuccessful.
Troubleshooting
A complete Halo Touchscreen Programming
and Troubleshooting Guide is available at
www.weiserlock.com/halo/support
SmartKey Re-Keying
Re-key the lock to work with your existing key. See the supplied
SmartKey Re-key instructions for more information.
Note: If Auto-Lock is enabled, remove the battery pack before
re-keying your lock.
Important Safeguards
-
Read all instructions in their entirety.
-
Familiarize yourself with all warning
and caution statements. -
Remind all family members of safety precautions.
-
Protect your user codes.
-
Dispose of used batteries according to local laws and
regulations.
WARNING: This Manufacturer advises that no lock
can provide complete security by itself. This lock may
be defeated by forcible or technical means, or evaded
by entry elsewhere on the property. No lock can
substitute for caution, awareness of your environment,
and common sense. Builder’s hardware is available in
multiple performance grades to suit the application.
In order to enhance security and reduce risk, you
should consult a qualified locksmith or other security
professional.
Read More About This Manual & Download PDF:
Halo Wi-Fi Touchscreen Smart Lock GED2500 User Manual – Optimized
PDF
Halo Wi-Fi Touchscreen Smart Lock GED2500 User Manual – Original
PDF
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>