Shark Wandvac WS630 Series Cordless Vacuum Cleaner User Manual
- June 8, 2024
- Shark
Table of Contents
IMPORTANT SAFETY INSTRUCTIONS
FOR HOUSEHOLD USE ONLY • PLEASE READ
ALL INSTRUCTIONS BEFORE USING THIS VACUUM.
If the charging cord plug does not fit fully into the outlet, reverse the
plug.
If it still does not fit, contact a qualified electrician. DO NOT force into
outlet
or try to modify to fit.
To reduce the risk of shock and unintended operation, turn off power and
remove the battery before servicing.
WARNING
To reduce the risk of fire, electric shock, injury, or property damage:
THE FLOOR NOZZLE, WAND, AND HAND VACUUM CONTAIN ELECTRICAL
CONNECTIONS:
-
This vacuum consists of a motorized
nozzle, wand, and hand vacuum.
These components contain electrical
connections, electrical wiring, and
moving parts that potentially present risk
to the user. -
Before each use, carefully inspect
all parts for any damage. If a part is
damaged, discontinue use. -
Use only identical replacement parts.
-
This vacuum contains no serviceable parts.
-
Use only as described in this manual.
DO NOT use the vacuum for any purpose
other than those described in this manual. -
With the exception of the filters and dust
cup, DO NOT expose any parts of the
vacuum to water or other liquids. -
Keep the appliance and its cord out
of reach of children. Do not allow the
appliance to be used by children. Do
not allow to be used as a toy. Close
supervision is necessary when used
near children.
GENERAL US -
This appliance can be used by persons
with reduced physical, sensory or mental
capabilities or lack of experience or
knowledge if they have been given
supervision or instruction concerning
use of the appliance in a safe way
and understand the hazards involved.
Cleaning and user maintenance shall not
be made by children. -
Always turn off the vacuum before
connecting or disconnecting any current
carrying hoses, motorized nozzles,
chargers, batteries, or other electrical or
mechanical parts. -
DO NOT handle plug or vacuum with
wet hands. -
DO NOT use without dust cup, filters,
and brushroll in place. -
Only use Shark® branded filters and
accessories. -
DO NOT put any objects into nozzle or
accessory openings. DO NOT use with
any opening blocked; keep free of dust,
lint, hair, and anything that may reduce
airflow. -
DO NOT use if nozzle or accessory
airflow is restricted. If the air paths or
the motorized floor nozzle become
blocked, turn the vacuum off. Remove all
obstructions before you turn on the unit again. -
Keep nozzle and all vacuum openings
away from hair, face, fingers, uncovered
feet, or loose clothing. -
DO NOT use if vacuum is not working
as it should, or has been dropped,
damaged, left outdoors, or dropped into
water. -
Use extra care when cleaning on stairs.
-
DO NOT leave the vacuum unattended
while powered on. -
When powered on, keep the vacuum
moving over the carpet surface at all
times to avoid damaging the carpet fibers. -
DO NOT place vacuum on unstable
surfaces such as chairs or tables. -
DO NOT use to pick up:
a) Liquids
b) Large objects
c) Hard or sharp objects (glass, nails,
screws, or coins)
d) Large quantities of dust (including
drywall, fireplace ash, or embers).
DO NOT use as an attachment to
power tools for dust collection.
e) Smoking or burning objects (hot coals,
cigarette butts, or matches)
f) Flammable or combustible materials
(lighter fluid, gasoline, or kerosene)
g) Toxic materials (chlorine bleach,
ammonia, or drain cleaner) -
DO NOT use in the following areas:
a) Poorly lit areas
b) Wet or damp surfaces
c) Outdoor areas
d) Spaces that are enclosed and may
contain explosive or toxic fumes
or vapors (lighter fluid, gasoline,
kerosene, paint, paint thinners,
mothproofing substances, or
flammable dust) -
Turn off the vacuum before plugging in or
unplugging the charger. -
Turn off the vacuum before any
adjustment, cleaning, maintenance or
troubleshooting. -
During cleaning or routine maintenance,
DO NOT cut anything other than hair,
fibers, or string wrapped around the
brushroll. -
Allow all filters to air-dry completely
before replacing in the vacuum to prevent
liquid from being drawn into electric parts. -
DO NOT modify or attempt to repair the
vacuum or the battery yourself, except as
indicated in this manual.
DO NOT use the battery or vacuum if it
has been modified or damaged.
Damaged or modified batteries may
exhibit unpredictable behavior resulting in
fire, explosion or risk of injury. -
Turn off all controls before unplugging.
-
Always turn off this appliance before
connecting or disconnecting motorized
nozzle or hand tool.
BATTERY PACK -
The battery is the power source for the
vacuum. Carefully read and follow all
charging instructions. -
To prevent unintentional starting, ensure
the vacuum is powered off before picking
up or carrying the vacuum. DO NOT
carry the appliance with your finger on
the power switch. -
Use only Shark® charger
DK12-133090A-U or E-TEK
ZD012S133090USD. Use of an incorrect
charger may result in no charging, and/or
unsafe conditions. -
Use only with Shark battery pack
XSBT330. -
Keep the battery away from all metal
objects such as paper clips, coins, keys,
nails, or screws. Shorting the battery
terminals increases the risk of fire or
burns. -
Under abusive conditions, liquid may
be ejected from the battery. Avoid
contact with this liquid, as it may cause
irritation or burns. If contact occurs, flush
with water. If liquid contacts eyes, seek
medical help. -
Battery should not be stored at
temperatures below 37.4°F (3°C) or
above 104°F (40°C) to maintain longterm
battery life. -
DO NOT charge battery at temperatures
below 40°F (5°C) or above 104°F (40°C). -
Store the appliance indoors. DO NOT use
or store it below 37.4°F (3°C). Ensure the
appliance is at room temperature before
operating. -
DO NOT expose the battery to fire or
temperatures above 265°F (130°C) as it
may cause explosion.
SAVE THESE INSTRUCTIONS
ASSEMBLY
-
Slide the Wand onto the neck of the PowerFins
Floor Nozzle until it clicks into place. -
Align the Hand Vacuum nozzle opening with the top
of the wand and slide it on until it clicks into place. -
Make sure the Dock Plate is facing upright. Slide
the Charging Post into the slot on back of dock
until it clicks. -
Place the dock on the floor near a wall outlet.
Plug the Wall Charger into the outlet, then
connect the cord to the port on the back of the
charging post. -
Store cleaning accessories on the mount on
the dock plate.
For proper operation, ensure all components are
completely connected and clicked into place
NOTE: Once the charging post is installed, it can’t be removed.
LI-ION BATTERY
Prior to first use, charge the battery completely. A full charge takes approximately 3.5 hours
RUNTIMES PER FULLY CHARGED BATTERY
Visit sharkclean.com/support online or review the included Quick Start Guide.
LED BATTERY POWER AND CHARGING INDICATORS
RECYCLING THE LI-ION BATTERY
When the Shark® Li-ion battery needs to be replaced, dispose of it or recycle
it in accordance with local ordinances or regulations. In some areas, it is
illegal to place spent lithium-ion batteries in the trash or in a
municipal solid waste stream. Return spent batteries to an authorized
recycling center or to the retailer for recycling. Contact your local
recycling center for information on where to drop off the spent battery.
NOTE: The Shark battery, like all lithium-ion batteries, will naturally decrease in capacity over time from the 100% capacity of
CHARGING WHILE IN STORAGE MODE
Charge the unit in upright mode by placing it on the
dock plate, with the hook on the back of the wand
over the charging post. Make sure the contacts
on the wand are aligned with the contacts on the
charging post. When charging is complete and you need to use
the unit again, lift it off the dock plate.
Detach the hand vacuum (see below). Charge the
unit by sliding the hand vacuum nozzle opening
over the post on the storage arm. To charge, make
sure the contacts on the hand vacuum are aligned
with the contacts on the storage arm.
When charging is complete and you need to use
the unit again, reattach the hand vacuum and use it
to lift the wand and nozzle off the dock plate.
To detach the hand vacuum from the wand, press
the release buttons on both sides of the handle and lift it off the wand.
To reattach the hand vacuum to the wand, align the
nozzle opening over the top of the wand and slide
it on until it clicks into place
NOTE: When docked properly, the charging lights on
the hand vacuum will blink, indicating that charging has
begun. When charging is complete, all three indicator
lights will remain on for 10 minutes, then shut off.
NOTE: The main unit comes with a partial charge.
For maximum runtime, charge fully before first use
(approximately 3 hours). Leaving the unit plugged in
will not damage battery life.
CHARGING
To charge the hand vacuum without the dock,
unplug the charger cord from the dock and connect
it directly to the port on the hand vacuum, near the
nozzle opening. To detach the hand vacuum, press
the release buttons on both sides of the handle and
lift it off the wand. (See previous page.)
To remove the battery from the hand vacuum,
press the release tabs on the battery cap and slide
out the battery. To reinstall, slide the battery
into the compartment in the handle until it clicks into place.
For quick and easy short-term storage, first attach the wand
storage clip by pressing it onto the front of the wand.
Lock the nozzle and wand in the upright position, and detach
the hand vacuum (see previous page). Hang the hand vacuum
from the wand storage clip, with the filter removal latch sitting
inside the clip.
To remove, slide the hand vacuum up and out. To remove the storage
clip, pull it off the wand.
Press the On/Off button on the handle to turn on
power. To turn off power, press the button again.
For an added boost of power, push and hold the
Boost button on the underside of the handle.
The Boost icon will blink white in this mode.
Release the button to return to standard powe
Use the PowerFins floor nozzle for powerful cleaning
on both bare floors and carpets. The brushroll is
activated when the hand vacuum is connected and
powered on, and the handle is tilted back
Detach the hand vacuum to clean above-floor areas.
Press the release buttons on both sides of the handle,
and lift the hand vacuum off the wand. To attach
an accessory to the hand vacuum, slide it into the
opening in the nozzle. To remove, press the release
buttons on both sides of the handle and slide out
the accessory.
To detach the floor nozzle from the wand, step on
the nozzle while pressing the nozzle release button
at the bottom of the wand. Lift the wand to remove
it. To reattach the wand, align it over the neck of
the floor nozzle, then slide it on until it clicks into place
NOTE: All accessories are compatible with both the wand
and the hand vacuum.
-
With the power off, slide the release button
forward, and the dust cup will swing open. Tap
the filter screen lightly to knock off dust and debris. -
Wipe the screen inside the dust cup lightly with a
dry cloth to remove dust and dirt.
NOTE: Do not wash any parts or accessories in a dishwasher.
-
With the dust cup open and the power off, press
the filter release latch below the handle and pull
out the filter housing. -
Press the tabs on both sides of the filter housing
and pull out the filter. To clean the filter, handwash
only with water and let air-dry for 24 hours
before reinstalling. To reinstall, slide it back into
the filter housing and press into place.
-
To deep clean the cup, first remove the Cyclone
Filter. Lift it out by the wire handle on the frame.
Rinse the dust cup with water, and wipe it clean
with a damp cloth. Allow it to air-dry for 24 hours. -
When the dust cup is completely dry, slide the
cyclone filter back into place. Tuck the wire handle
away, then reinstall the dust cup.
-
Turn off the vacuum.
-
Press the nozzle release button to detach the
nozzle from the wand. -
Using a coin, turn the 3 locks counterclockwise
to open, then lift off the cover and tilt back the
neck of the nozzle. -
Clear any blockages and remove any debris
from the brushroll and floor nozzle. -
With the cover removed, wipe the brushroll
clean with a dry towel. -
Replace the cover by sliding the tabs into the
slots. Press down firmly on all sides. Turn locks
clockwise to close, until they click into place
CHECKING FOR BLOCKAGES
If you run over a hard or sharp object or notice a noise change while vacuuming, check for blockages or objects caught in the brushroll.
Checking for
Blockages in the Hand vacuum:
1. Turn off the vacuum.
2. Remove the hand vacuum from the wand.
3. Check all intake openings to the dust cup and
remove any debris or blockages
Checking for
Blockages in the Wand:
1. Turn off the vacuum.
2. Detach the hand vacuum and floor nozzle from
the wand.
3. Check both ends of the wand for blockages and
debris. 4. Clear away any debris or blockages.
Checking for
Blockages in the Floor Nozzle:
1. Turn off the vacuum.
2. Detach the wand.
3. Using a coin, turn the 4 locks on the bottom of
the nozzle counterclockwise to open.
4. Lift off the nozzle cover and tilt back the neck of
the nozzle.
5. Check the opening and remove any debris.
6. Replace the cover by sliding the tabs into the
slots. Press down firmly on all sides. Turn the locks clockwise to close.
MAINTAINING YOUR VACUUM
TROUBLESHOOTING
WARNING: To
reduce the risk of shock and unintended operation, turn off power and remove
the battery before servicing.
Vacuum is not picking up debris. No suction or light suction. Third indicator
light on hand vacuum is solid yellow.
(Refer to Checking for Blockages section for more information.)
- Dust cup may be full; empty dust cup.
- Check floor nozzle for blockages; clear blockages if required.
- Remove any string, carpet fibers, or hair that may be wrapped around the brushroll.
- Check connection between hand vacuum and wand for blockages; clear blockages if required.
- Check filters to see if they need cleaning. Follow instructions for rinsing and completely air-drying the
filters before reinstalling them.
Vacuum lifts area rugs.
-
Make sure you are not engaging Boost mode. Take care when vacuuming area rugs or rugs with delicately sewn edges.
-
Turn off the unit to disengage from the carpet, then restart.
My vacuum has a PowerFins nozzle but the brushroll doesn’t spin. -
Immediately turn off the vacuum. Remove any blockages before turning the vacuum back on. Make sure
the hand vacuum is tilted back far enough for the brushroll to engage while in use. -
If the floor nozzle has headlights and they are not illuminated, there is a connection issue between the hand vacuum, wand, and nozzle. Try detaching the parts, then reconnecting them.
Vacuum turns off on its own.
There are several possible reasons for the vacuum turning off on its own,
including blockages, battery issues, and overheating. If vacuum turns off on
its own, perform the following steps:
-
Turn on the vacuum and check the battery indicator lights on the hand vacuum. If recharging is needed,
make sure vacuum power is off before plugging in the charger. -
Empty dust cup and clean filters (See the Cleaning the Dust Cup and Filter section).
-
Check wand, accessories, and inlet openings and remove any blockages.
-
Allow unit and battery to cool for at least 45 minutes, until they return to room temperature.
-
Press the On/Off switch to restart the vacuum.
Battery Indicator Lights on hand vacuum are flashing.
NOTE: If vacuum still does not operate properly, contact Customer Service at 1-800-798-7398 or sharkclean.com/support.
-
Bottom LED is solid yellow (Fig. A): Nozzle clog.
(See the Maintaining Your Vacuum section.) -
Top LED is flashing (Fig. B): Battery needs to
be charged.
Contact Customer Service at 1-800-798-7398
or sharkclean.com if you experience any of the
indications listed below: -
Top two LEDs are flashing (Fig. C): Overcurrent or short.
-
Top and bottom LEDs are flashing (Fig. D): Motor
is overheating. -
Middle LED is flashing (Fig. E): Overspeed.
-
Bottom LED is flashing (Fig. F): Communication.
-
Bottom LED blinking yellow (Fig. G): There may
be an electrical problem with the nozzle.
ADDITIONAL ACCESSORIES AVAILABLE ON SHARKACCESSORIES.COM
A Crevice Tool 
B Duster Crevice Tool
C Upholstery Tool
D Wide Upholstery Tool
E Pet Multi-Tool
F Motorized Hand Tool
G Replacement Battery
H Li-Ion Charger
I Battery Charging Sleeve
NOTE: Not all accessories come with all units. Please see the enclosed
Quick Start Guide for your unit’s configuration.
To order additional accessories, visit sharkaccessories.com.
FIVE (5) YEAR LIMITED WARRANTY
The Five (5) Year Limited Warranty applies to purchases made from authorized
retailers of SharkNinja
Operating LLC. Warranty coverage applies to the original owner and to the
original product only and is not transferable.
SharkNinja warrants that the unit shall be free from defects in material and
workmanship for a period
of five (5) years from the date of purchase when it is used under normal
household conditions and maintained according to the requirements outlined in
the Owner’s Guide, subject to the following conditions and exclusions:
What is covered by this warranty?
-
The original unit and/or non-wearable components deemed defective, in SharkNinja’s sole discretion,
will be repaired or replaced up to five (5) years from the original purchase date. -
In the event a replacement unit is issued, the warranty coverage ends six (6) months following the receipt date of the replacement unit or the remainder of the existing warranty, whichever is later.
SharkNinja reserves the right to replace the unit with one of equal or greater value.
What is not covered by this warranty?
-
Normal wear and tear of wearable parts (such as foam filters, HEPA filters, pads, etc.), which require regular maintenance and/or replacement to ensure the proper functioning of your unit, are not covered
by this warranty. Replacement parts are available for purchase at sharkaccessories.com. -
Any unit that has been tampered with or used for commercial purposes.
-
Damage caused by misuse (e.g., vacuuming up water or other liquids), abuse, negligent handling, failure to perform required maintenance (e.g., not cleaning the filters), or damage due to mishandling in transit.
-
Consequential and incidental damages.
-
Defects caused by repair persons not authorized by SharkNinja. These defects include damages caused in the process of shipping, altering, or repairing the SharkNinja product (or any of its parts) when the
repair is performed by a repair person not authorized by SharkNinja. -
Products purchased, used, or operated outside North America.
How to get service
If your appliance fails to operate properly while in use under normal
household conditions within the warranty
period, visit sharkclean.com/support for product care and maintenance self-
help. Our Customer Service
Specialists are also available at
1-800-798-7398 to assist with product
support and warranty service options, including the possibility of upgrading
to our VIP warranty service options for select product categories. We
also ask that you register your product online at registeryourshark.com and
have the product on hand when you call, so we may better assist you.
SharkNinja will cover the cost for the customer to send in the unit to us for
repair or replacement. A fee of
$24.95 (subject to change) will be charged when SharkNinja ships the repaired
or replacement unit.
How to initiate a warranty claim
You must call 1-800-798-7398 to
initiate a warranty claim. In order to better assist you please register your
product prior to calling and have your product with you at the time of your
call. You will need the receipt as proof of purchase. A Customer Service
Specialist will provide you with return and packing instruction
information. We also ask that you register your product online at
registeryourshark.com and have the
product on hand when you call, so we may better assist you.
How state law applies
This warranty gives you specific legal rights, and you also may have other
rights that vary from state to state. Some states do not permit the exclusion
or limitation of incidental or consequential damages, so
the above may not apply to you.
TWO (2) YEAR LIMITED BATTERY WARRANTY
The Two (2) Year VIP Limited Warranty applies to purchases made from
authorized retailers of SharkNinja
Operating LLC. Warranty coverage applies to the original owner and to the
original product only and is not transferable.
SharkNinja warrants that the battery shall be free from defects in material
and workmanship for a period of
two (2) years from the date of purchase when it is used under normal household
conditions and maintained according to the requirements outlined in the
Owner’s Guide, subject to the following conditions and exclusions:
What is covered by this warranty?
-
The original battery deemed defective, in SharkNinja’s sole discretion, will be replaced up to two (2) years
from the original purchase date. -
In the event a replacement battery is issued, the warranty coverage ends six (6) months following the receipt
date of the replacement battery or the remainder of the existing warranty, whichever is later. SharkNinja
reserves the right to replace the unit with one of equal or greater value.
What is not covered by this warranty?
-
Normal wear and tear of the battery, which requires optimal temperature storage and operation to ensure
its proper functioning. Replacement batteries are available for purchase at sharkclean.com/batteries. -
A battery that has been tampered with or used for commercial purposes.
-
Damage caused by misuse (e.g., exposing battery to liquids or extreme hot and/or cold temperatures),
abuse, negligent handling, failure to perform required maintenance, or damage due to mishandling in transit. -
Consequential and incidental damages.
-
Defects caused by repair persons not authorized by SharkNinja. These defects include damages caused in
the process of shipping, altering, or repairing the SharkNinja product (or any of its parts) when the repair is
performed by a repair person not authorized by SharkNinja. -
Products purchased, used, or operated outside North America.
How to get service
If your battery fails to operate properly while in use under normal household
conditions within the warranty
period, visit sharkclean.com/support for product care and maintenance self-
help. Our Customer Service
Specialists are also available at
1-800-798-7398 to assist with product
support and warranty service options.
So we may better assist you, please register your product online at
registeryourshark.com and have the
product on hand when you call.
SharkNinja will cover the cost for the customer to send in the unit to us for
replacement. A fee of $19.95 (subject
to change) will be charged when SharkNinja ships the replacement unit.
How to initiate a warranty claim
You must call 1-800-798-7398 to
initiate a warranty claim. You will need the receipt as proof of purchase. We
also ask that you register your product online at registeryourshark.com and
have the product on hand when
you call, so we may better assist you. A Customer Service Specialist will
provide you with return and packing
instruction information when you call.
How state law applies
This warranty gives you specific legal rights, and you also may have other
rights that vary from state to state.
Some states do not permit the exclusion or limitation of incidental or
consequential damages, so the above may not apply to you
RECORD THIS INFORMATION
Model Number:
Date Code: ____
Date of Purchase:
(Keep receipt)
Store of Purchase:
TIP: You can find the model and serial numbers on
the QR code label on the bottom of the back of the
hand vacuum and battery.
TECHNICAL SPECIFICATIONS
Voltage: 11.1V
BATTERY REMOVAL AND DISPOSAL
This product uses a lithium-ion rechargeable and recyclable battery. When the
battery no longer holds a
charge, it should be removed from the vacuum and recycled. DO NOT incinerate
or compost the battery.
When your lithium-ion battery needs to be replaced, dispose of it or recycle
it in accordance with local
ordinances or regulations. In some areas, it is illegal to place spent
lithium-ion batteries in the trash or in a
municipal solid waste stream. Return spent battery to an authorized recycling
center or to retailer for recycling.
Contact your local recycling center for information on where to drop off the
spent battery.
The RBRC™ (Rechargeable Battery Recycling Corporation) seal on the lithium-ion
battery indicates that the
costs to recycle the battery at the end of its useful life have already been
paid by SharkNinja. In some areas,
it is illegal to place spent lithium-ion batteries in the trash or municipal
solid waste stream and the RBRC
program provides an environmentally conscious alternative.
RBRC, in cooperation with SharkNinja and other battery users, has established
programs in the United
States and Canada to facilitate the collection of spent lithium-ion batteries.
Help protect our environment
and conserve natural resources by returning the spent lithium-ion battery to
an authorized SharkNinja
service center or to your local retailer for recycling. You may also contact
your local recycling center for
information on where to drop off the spent battery, or call
1-800-798-7398.
PLEASE READ CAREFULLY AND KEEP FOR FUTURE REFERENCE.
This Owner’s Guide is designed to help you get a complete understanding of
your new
Shark® vacuum.
SharkNinja Operating LLC
US: Needham, MA 02494
CAN: Ville St-Laurent, QC H4S 1A7
1-800-798-7398
sharkclean.com
Illustrations may differ from actual product. We are constantly striving to
improve our products;
therefore the specifications contained herein are subject to change without
notice.
For SharkNinja U.S. Patent information, visit
sharkninja.com/uspatents
© 2020 SharkNinja Operating LLC. SHARK is
a registered trademark of SharkNinja Operating LLC.
WANDVAC is a
trademark of SharkNinja Operating LLC. RBRC is a trademark of Rechargeable
Battery Recycling Corporation. 
WS630Series_IB_E_REV_Mv9
PRINTED IN CHINA
Read More About This Manual & Download PDF:
Shark Wandvac WS630 Series Cordless Vacuum Cleaner User Manual – Optimized
PDF
Shark Wandvac WS630 Series Cordless Vacuum Cleaner User Manual – Original
PDF
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>