Bebe Stars Λίκνο Side to Side Plus 2in1 Pacific User Manual
- June 16, 2024
- Bebe Stars
Table of Contents
user’s manual
Λίκνο Side to Side Plus 2in1 Pacific
item: 841
AGE RANGE
baby cot: 0-6 m or up to 9 kgs
play yard: 0-36 m or up to 15 kgs
STANDARDS
EN 1130:2019 |
EN 12227:2010
DO NOT USE THIS PRODUCT BEFORE YOU READ AND UNDERSTAND THESE INSTRUCTIONS
SAFETY WARNINGS
IMPORTANT! READ CAREFULLY AND KEEP FOR FUTURE REFERENCE.
– Do not use this product without reading the instrucons for use first.
– Stop using the product as soon as the child can sit or kneel or pull itself
up.
– Placing addional items in the product may cause suffocaon.
– Do not place the product close to other objects, which could present a
danger of suffocaon or strangulaon, e.g. strings, blinds/curtain cords, etc.
– The product should be placed on a horizontal floor.
– Young children shouldn’t be allowed to play unsupervised in the vicinity of
the crib.
– The crib should be locked in the fixed posion when the child is le unaended.
– All assembly fings should always be ghtened properly and care should be taken
that no screws are loose, because a child could trap parts of the body or
clothing (e.g. strings, necklaces, ribbons for babies’ dummies, etc.), which
would pose a risk of strangulaon.
– Be aware of the risk of burning cigarees, open fires and other sources of
strong heat, such as electric bar fires, gas fires, etc. in the near vicinity of
the crib.
– DO NOT use crib if any parts are missing, damaged, or broken. Contact the
manufacturer for replacement parts and instrucons if needed. DO NOT substute
parts.
– Use only accessories or spare parts sold or approved by the manufacturer.
– Only use the maress sold with this crib, do not add a second maress on this
one, there is a suffocaon hazard.
PARTS LIST
- Bassinet
- Maress
- Supporng tube legs (x2)
- Linking tube
- Mounng straps
- Base support bars (x2)
- Allen wrench
- Screws (x4)
- Nut & bolt (x2)
ASSEMBLE INSTRUCTIONS
frame assembly
HOW TO USE
height adjustment/ leg extension/drop side
bedside sleeper
play yard mode
ASSEMBLY INSTRUCTIONS
Baby cot assembly: (Figures 1, 2, 3, 4)
- Install the bedstead: Install the stand tube a,b and linking tube c according to the direction of the arrow.
- Each side is equipped with two screws to fix the bedstands.
- Use allen wrench to tighten screws in clockwise direction.
- The bedstead and the baby cot: let bedstead pass through the casing cloth and then insert handrail joint into stand tube (Fig. 3A). Secure by inserting bolt through holes and screwing nut clockwise (Fig. 3B).
- The bedstead and the baby cot: Install the long handrail according to the direction of the arrow(Press the handrail button). Pull the zipper up in the direction of the arrow.
HOW TO USE
– height adjustment: (Figure 5)
- Press the button down to adjust the height, it has 5 positions to choose and match with the height of parent’s bed.
- Different position of each side cause different slope angle. With one side tilted to help baby breathe easily in special fever time.
– leg extension: (Figures 6, 7)
- Press button down and pull leg out to adjust the length. There are only two positions to choose.
- Hold long handrail at the back side, lift it up and push forward to move by wheels.
And there is anti-sliper at the bottom of leg to stop moving.
– drop side: (Figure 8)
Open zipper, pull handrail out as figure shows, put it down and apply the snap
buttons.
– bedside sleeper warnings: (Figure 9)
– DO NOT use bedside sleeper if any parts are missing, damaged, or broken.
Contact the manufacturer for replacement parts and instructional literature if
needed. DO NOT substitute parts.
– To prevent a suffocation hazard from entrapment, the bedside sleeper shall
be properly secured to the adult bed using the attachment system.
– Check the tightness of the attachment system before each use by pulling the
bedside sleeper in a direction away from adult bed.
– If there is any gap between the bedside sleeper and the adult bed DO NOT use
the product.
– Gaps should not be filled with pillows, blankets or other items.
– To avoid hazards from the child’s neck being caught on the top rail on the
side that is next to the adult bed, the top rail must not be higher than the
adult bed mattress.
– To avoid the risk of your child being strangled the attachment system to the
adult’s bed shall always be kept away from and out of the baby cot.
– The attachment system shall be provided and the user shall not use other
attachment system.
– The bedside sleeper shall never be used in an inclined position.
– THIS BEDSIDE SLEEPER MUST BE ONLY USED WITH STANDARD TYPE ADULT BEDS.
DO NOT USE the bedside sleeper with atypical shape beds: The height from the
floor of the adult bed on which the bedside sleeper may be installed shall be
between 56 and 68 cm.
– bedside sleeper mode: (Figures 10, 11, 12, 13, 14)
-
Move the baby cot close to the adult bed and check the height of the baby cot compared with the mattress of the bed.
WARNING!!! The mattress of adult bed must be aligned to or over the height of the drop side in the lowest position. In co-sleeping mode the 2 legs of the baby cot should always be adjusted to the same height. -
Use the pair of straps provided to fix the baby cot to the parents bed. Fix the buckles underneath the baby cot on left and right leg frame. Next, fix the buckles to the inner side of both frame stands.
-
Finally, fix the straps around the structure/slats of the parent’s bed, from the bottom towards the top and fasten the buckles to finish.
-
To secure the baby cot to the adult bed, adjust the “D” buckle to tighten and pull the straps once more to ensure the baby cot is properly and firmly secured to the adult bed.
WARNING! – There shall never be a gap between the lower side of the
bedside sleeper and the mattress of the adult bed.
The mattress of the adult’s bed shall be aligned to or over the height of the
drop side in the lowest position.
– play yard WARNINGS:
– Suit for child under 15kgs in weight or approximately 3 years old.
– Attend the child at any time.
– Never hang anything up on the play yard.
– Do not use the play yard without the base.
– Do not place the play yard close to an open fire or other heat source.
– Ensure that the play yard is fully erected and all the locking mechanisms
engaged before placing your child in this play yard.
– Do not use the play yard if any part is broken, torn or missing and use only
spare parts approved by the manufacturer. Do not use the accessories which are
not approved by the manufacturer. Never leave anything in the play yard which
could provide a foothold or create a danger of suffocation or strangulation.
– The base should always be used in the highest position.
– Ensure all assembly fittings should always be tightened properly.
– play yard mode: (Figure 15)
- The bottom of the crib body provided with zippers.
- Unzip bottom to lower down the base to floor so it converts to play yard mode.
WARNING! In play yard mode, the frame should always be used in the highest position.
MAINTENANCE & CLEANING
– The baby cot and mattress have a resistant fabric cover, which are
removable.
– On a regular basis check the condition of the product and the presence of
any possible damage. In the case of damage, do not use the product and keep
out of reach of children.
– To prolong the life of your nursery product, keep clean and do not leave it
in direct sunlight for extended periods of time. Prolonged exposure to
sunlight may cause changes in the color of materials and fabrics.
| No bleach
---|---
| Do not iron
| Do not dry clean
| No tumble dryer
| Hand washing under 40°
LET’S START A NEW
JOURNEY TOGETHER!
Thank you for choosing Bebe Stars products
SCAN ME
https://www.bebestars.gr/?s=841-&lang=en
FOLLOW US
bebestarsbygilis
@bebe.stars
**** bebestarsbygilis
ADDRESS
G. Gkilis & SIA OE
2nd Km N. Moudania-Sithonia Str.
PO: 63200 N. Moudania Greece
T.: +3023730-23585
www.bebestars.gr
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>