Corsair COMMANDER PRO Digital RGB Lighting and Fan Speed Controller User Manual
- June 8, 2024
- Corsair
Table of Contents
COMMANDER PRO
Digital RGB Lighting and Fan Speed Controller
COMMANDER PRO
Congratulations!
Congratulations on the purchase of your new CORSAIR Commander PRO!
The CORSAIR Commander PRO is the heart of your CORSAIR iCUE powered system.
Customize and create stunning RGB lighting effects when you connect CORSAIR
RGB lighting strips and RGB fans for an amazing system-wide light-show.
Control and adjust up to six DC or PWM fans, create custom fan curves tied to
internal temperature sensors or switch fans off entirely with a Zero-RPM fan
mode. Accurately monitor temperatures inside your system using four
repositionable thermistors, and then use CORSAIR iCUE software to
automatically control fan speeds and system lighting to match your PC’s
performance. Unlock the power of iCUE with CORSAIR Commander PRO, bringing
intelligent control and unlimited possibilities to any PC.
Package Contents
x1 – CORSAIR Commander PRO
x2 – RGB LED hub cables
x4 – Thermal sensors
x4 – Fan extension cables
x2 – Mounting tape
x1 – Installation guide
Specifications
- Supported by CORSAIR iCUE software. Additional RGB LED strips sold separately.
** RGB LED hub required; sold separately.
Installation
-
Turn your system off for the installation of your Commander PRO.
-
Locate an area to mount your Commander PRO. Adhere it onto the desired location with the double-sided tape.
-
Connect any 3-pin or 4-pin fans you wish to control into the 4-pin headers labeled “Fans 1-6”. The included fan extension cables can be used if necessary.
-
Connect the thermal sensors to the 2-pin headers labeled “Temp 1-4”.
TIP: The thermal sensors are designed to measure ambient temperatures, so for the most accurate results, they should not directly touch components. You may find it useful to mount the thermal sensors near air intake and exhaust points, and if your PC case has multiple compartments, you can try placing each of the sensors in its own compartment. Since the thermal sensors can easily be repositioned, you can try various locations and use what works best for you. -
OPTIONAL: Connect the individually addressable RGB LED strips (sold separately) to the 3-pin connectors labeled “LED 1-2”. Alternatively, connect your CORSAIR RGB fans to the Commander PRO via the RGB LED hub (sold separately) using the supplied RGB LED hub cables.
WARNING! Please refrain from mounting the strips on components (HDD, SSD)
that are sensitive to magnets. -
Connect compatible iCUE components such as the Lighting Node PRO (sold separately) into an available 9-pin USB 2.0 header on the Commander PRO. Ensure that these devices are properly powered (see device manual).
-
Plug the USB cable from the Commander PRO into an available internal USB 2.0 header on your PC’s motherboard (refer to your motherboard manual for location).
-
Connect the SATA power connector to any available SATA connector from your power supply.
-
Internet connection is required to download the latest CORSAIR iCUE software at www.corsair.com/downloads.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
(1) Reorient or relocate the receiving antenna.
(2) Increase the separation between the equipment and the receiver.
(3) Connect the equipment into an outlet that is on a circuit different from
that to which the receiver is connected.
(4) Consult the dealer or an experienced radio/TV technician for help.
FCC CAUTION:
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment.
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations. CAN ICES-3)B(/NMB-3 (B)
CORSAIR MEMORY, Inc. declares that this radio equipment model “RWF0020” is in
compliance with Directive 2014/30/EU and Directive 2011/65/EU. A copy of the
original declaration of conformity can be obtained at
“regulatory@corsair.com”. Operating temperature: 0°C ~ + 40°C.
NOTE ON ENVIRONMENTAL PROTECTION
After the implementation of the European Directive 2012/19/EU in the national
legal system, the following applies:
— Electrical and electronic devices may not be disposed of with domestic
waste.
— Consumers are obliged by law to return electrical and electronic devices at
the end of their service lives to the public collecting points set up for this
purpose or point of sale. Details to this are defined by the national law of
the respective country. This symbol on the product, the instruction manual or
the package indicates that a product is subject to these regulations. By
recycling, reusing the materials or other forms of utilising old devices, you
are making an important contribution to protecting our environment.
COMMANDER PRO
WEB: corsair.com
PHONE: 888-222-4346
SUPPORT: support.corsair.com
BLOG: corsair.com/blog
FORUM: forum.corsair.com
YOUTUBE: youtube.com/corsairhowto
© 2017-2019 CORSAIR MEMORY, INC. All rights reserved. CORSAIR and the sails logo are registered trademarks in the United States and/or other countries. All other trademarks are the property of their respective owners. Product may vary slightly from those pictured. 49-001531 AF
Corsair COMMANDER PRO Digital RGB Lighting and Fan Speed Controller User
Manual – Download [optimized]
Corsair COMMANDER PRO Digital RGB Lighting and Fan Speed Controller User
Manual – Download
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>