VOXX ALQ100 LED Desk Lamp with Wireless Charging User Guide
- June 5, 2024
- Voxx
Table of Contents
ALQ100 LED Desk Lamp with Wireless Charging
LED DESK LAMP
WITH WIRELESS CHARGING
User’s Guide
Getting Started
Step 1: Plug In
1. Plug the included power adapter into the power jack on the back of the
lamp.
2. Plug the other end of this cable into a working power outlet.
BATTERY BACKUP
Your clock has a pre-installed battery backup that will keep the time in case
power is interrupted (like by a power outage, for example). To start using the
battery backup, pull the activation tab above the battery door on the back of
the lamp. The protective film covering the battery will come of with the tab
and the battery will be activated.
If you notice that battery backup is no longer working, simply replace the
CR2032 coin-cell battery in the battery compartment on the back of the lamp.
Use a coin to turn the battery door and unlock it. Then remove the door and
access the CR2032 battery.
Step 2: Unfold and turn on the lamp
This lamp has 2 articulating arms for complete flexibility in angle and placement. Unfold the lamp completely and experiment with both arms until you find the position and angle you prefer.
To turn on the lamp: Press on the base of the lamp.
Step 2: Set the Time and Date
When you first plug it in, the lamp’s clock display shows 12:00.
- Press on the back of the lamp.
- Press and on back of the lamp to adjust the hour. Press to set the hour and move to the minutes.
- Press and to adjust the minutes. Press to set the minutes and move to the year.
- Press and to adjust the year. Press to set the year and move to the date.
- Press and to adjust the date. Press to finish setting the time and date.
Note: By default, the clock uses the 12-hour format (for example, 5:00 pm instead of 17:00). To switch between 12- and 24-hour format, press .
Everyday Use
Setting the Alarm
-
Press on the back of the lamp to display the alarm time.
-
Press on the back of the lamp to adjust the alarm time.
-
Press and on back of the lamp to adjust the alarm hour. Press to set the hour and move to the minutes.
-
Press and to adjust the alarm minutes. Press to set the minutes and move to the snooze time.
-
Press and to adjust the amount of alarm delay for snooze.
Press to set the snooze time and move to the alarm sound/ music. -
Press and to select the sound/music you want to use for the alarm. Press to select it and finish setting the alarm.
To turn the alarm on/off: Press on the back of the lamp to display the alarm time. Then press and on back of the lamp to turn on the alarm and/or snooze function.
- One press turns on the alarm.
- Two presses turns on the alarm and snooze function (alarm sounds for one minute, then snoozes).
- Three presses turns off alarm and snooze.
Note: The alarm sounds for 1 minute when activated.
Setting the Display Brightness
The clock display defaults to its highest brightness setting when you first
plug the lamp in.
To adjust display brightness: Press on the back of the lamp. Each press goes
to the next setting–minimum, medium, and maximum.
Using the Lamp
The lamp offers 5 brightness levels and 3 color temperature settings. To turn on the lamp: Press on the base of the lamp. To adjust the lamp’s brightness: Press and on the base of the lamp. To adjust the lamp’s color temperature: Press on the base of the lamp. Each press goes to the next temperature setting (cool, warm, and neutral).
Charging your Device
IMPORTANT: Before you try to charge your device, make sure it is compatible
with wireless charging. If your device has a metal case, remove it before you
put the device on the charger.
1. Place your wireless charging-compatible device directly onto the charging
pad on base of the lamp. Refer to the placement illustration here as a guide.
The charging indicator on the base of the lamp turns red while your device is
charging. It turns green when your device has finished charging. Check your
device’s screen to see the progress of charging. You can remove your device at
any time during charging.
Important: If the charging indicator light starts blinking, there’s something
interfering with the charging. Make sure there are no objects between your
phone and the charging pad. You might need to remove your phone’s case to
charge wirelessly.
2. When your device is completely charged, remove it from the charging pad.
Note: The lamp must be plugged in to provide wireless charging.
Tour of the Wireless Charging Alarm Clock
Display
Time/alarm display shows the current time. Press to display the alarm time.
on the lamp base
MONTH DATE DAY display shows the current month, day, and day of the week.
MONTH DATE
DAY
Temperature display shows the current indoor temperature. Press on the back of the lamp to switch between Celsius and Fahrenheit.
Base
Wireless charging pad and indicator lets you charge compatible devices wirelessly when the lamp is using AC power. The indicator turns solid red while your device is charging and turns green when your device is charged. The charging indicator blinks when there is a problem charging.
cycles through the lamp’s color temperature settings (cool, warm, and
neutral).
and cycles through the lamp’s 5 brightness settings.
Back
cycles through the 3 display brightness settings. switches between time and alarm time display.
enters time/date set or alarm set modes.
and increases or decreases the flashing value when setting time, date, or
alarm. Activates the alarm and/or snooze when the alarm time is displayed.
switches between 12- and 24-hour time when the time is displayed. switches
between Celsius and Fahrenheit temperature display when the time is displayed.
Backup battery compartment houses the backup battery so the display keeps time
even if there’s a power outage.
Power jack (not shown) plugs into the provided charging adapter to power the
lamp.
Backup battery compartment
www.Acoustic-Research.com
ALQ100 IB 00
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>