HGLRC FD765-VTX Stack Manual

HGLRC FD765-VTX Stack

Package Included

Product Specifications

Product parameters

Model

|

HGLRC FD765-VTX STACK

Usage

|

for 180mm-1000mm Frame Kit

Input Voltage

|

3-6S Lipo

Flight Controller

|

Forward F7 Dual Gyro Flight

Controller

ESC

| FD65A L431 4in1 ESC

VTX

|

FD VTX

Support Neceiver

|

SBUS .PPM .DSMX

Product Size

|

464530mm

30.5mm mounting holes(M3)

Weight|

48.2g (Including Receiver)

Interface Description

Check the flight control drive

1. Long Press BOOT buttons. Connect USB. The system automatically install the driver
   

2. Driver cannot be installed, please download ImpulseRC_Driver_Fixer

3. Double-click on the run(Plug in the flight controller to automatically install the driver)
   

4. Open betaflight configurator ，enter DFU mode （It is recommended to use the latest Betaflight version)
   

5. Click Select firmware version (Dual 8K is recommended. (Betaflight 4.0 firmware does not support 32K)

6. Click Load firmware. Waiting for completion It will be prompted upon completion.

7. open betaflight configurator 。Controller plugged into the computer. Betaflight Automatically assigned port click “Connect” Enter setup interface (Different computer COM)
   

Calibration accelerometer

1. Put the aircraft horizontal and click“Reset Z axis” Click again

URAT serial port use

URAT1 uses receiver telemetry
URAT2 uses the receiver
URAT3 uses VTX image transmission
URAT6 uses GPS
URAT7 uses ESC telemetry

Select aircraft model

1. Click Select model
   

2. Click Click “I understand the risks ”Push Master to check motor steering “Master” Steering can be changed at BLHeliSuite
   

Choose ESC/Motor protocol

1. Choose the correct ESC / Motor protocol, Protocol DSHOT1200 is recommended for Wind5 Hybrid racing drone
   

Voltage and current parameters setting

1. Click Setting parameters
   

Setting up the receive

1. Receiver connection diagram
   

2. Click .have found“UART2”Open the receiver serial port
   

3. Set the SBUS receiver
   

4. Set the PPM receiver
   

5. Set the DSMX receiver
   

6. Turn on the receiver telemetry serial port Function on
   

VTX uses OSD smart audio

1. VTX connection diagram
   

2. VTX serial port opens. The protocol is selected according to its own VTX protocol.
   

3. Fourth, frequency and power control methods:
   1. Button frequency control: Short press once to change channel number CH (CH1-CH8) long press for 2 seconds and then short press to change frequency group FR （A-B-E-F-R-L）
   2. Button power control: Long press button for 6 seconds and then short press button to change power level PIT/25mw/50mw/100mw/200mw/ 400mw:

4. Use OSD to adjust VTX
   which displays information like battery voltage and mAh consumed while you fly. In addition, the Betaflight OSD can be used to configure the quadcopter, making in-field adjustments and tuning more convenient.
   
   The graphics above show the stick command to bring up the OSD menu. The stick command is: throttle centered, yaw left, pitch forward. The exact stick command therefore depends on which mode your transmitter sticks are in.
   In the OSD menu, use pitch up/down to move the cursor between menu items. When a menu option has a > symbol to the right of it, this indicates that it contains a sub-menu. Roll-right will enter the sub-menu. For example, in the screen to the right, moving the cursor to “Features” and then moving the roll stick to the right will enter the “Features” sub-menu.
   
   If you are using a video transmitter that supports remote configuration, enter the “Features” menu to configure the vTX. From there, enter either “VTX SA” if you are using SmartAudio (TBS Unify) or “VTX TR” if you are using IRC Tramp Telemetry.
   To adjust PIDs, rates, and other tuning-related parameters, enter the “Profile” sub-menu. In the “Scr Layout” sub-menu, you can move the OSD
   elements (like battery voltage, mAh, and so forth) around on the screen. The “Alarms” sub-menu lets you control when the OSD will try to alert you that battery voltage is too low or mAh consumed is too high.
   
   When a parameter can be modified, the parameter’s current value will be shown on the right-hand side of the screen. In this case, roll left/right will adjust the parameter up and down.
   The screen to the right shows the current vTX settings. From here, you can change the frequency band, channel, and power level of the video transmitter. After making the changes, move the cursor to “Set” and press roll-right to confirm the settings.
   

GPS parameters setting

1. GPS connection diagram
   

2. Open the GPS serial port
   

3. When using the GPS function, remember to configure the serial port (via the Ports tab).
   

Check receiver signal

1. Click Check the remote control output signal
   

Select flight mode startup mode

1. Click set up the function of remote control switch across the channel (below are for reference only)
   

LED settings

1. Click Turn on LED support

2.Click .Click set according to need

Switching gyro

1. After connecting to the Betaflight ground station, open the page and enter “ get gyro_to_use ” and press Enter to view the currently used gyro scope. First is MPU6000.SECOND is ICM20608（ Set the MPU6000input:gyro_to_use = FIRST ）（ Set the ICM20608 input: set gyro_to_use =SECOND ）

Troubleshooting

Warning:

Please read the cautions as follows, otherwise stability of your flight controller cannot be ensured, your flight controller will even get damaged.

• Keep focus on the polarity. Check carefully before power supply.
• Cut off the power when you connect, plug and pull anything.
• The refresh rate of PID and Gyroscope is up to 32K/16K.

after sales question:

1. After receiving the goods, it is found that the product can not be used normally. If the return to the factory is a quality problem, the repair service will be provided free of charge.
2. If the product is damaged due to improper operation, the repair service may be provided under the condition that the inspection can be repaired.
3. For domestic customers, please contact the after-sales service personnel. For overseas customers, please contact the official website for after-sales service.

Product daily problems

1. OSD garbled:
   If you find garbled characters, please open Betaflight, click “OSD” .and click “Font Manager ” clicks on “ Upload Font” to update

2. When plugged in the battery, the aircraft does not pass the self-test without “BBB” sound.
   There is only one sound. Please check if the ESC agreement is correct

3. The spin of the aircraft keeps spinning
   1. Please check if the propeller is correct
   2. Please check if the motor direction is correct

HGLRC FD765-VTX Stack Manual – Download [optimized]
HGLRC FD765-VTX Stack Manual – Download

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>