WALKSNAIL Avatar Mini 1S Digital HD Video Kit User Guide

WALKSNAIL Avatar Mini 1S Digital HD Video Kit User Guide

Connection

1. *Power 3.1V-5V
2. Power G\D
3. Uart RX(Connects to Flight Controller TX)
4. Uart TX(Connects to Flight Controller RX)
5. USB—DP
6. USR—DM
7. USB—GND
8. USB-5V

*The voltage input should not exceed 5V

Linking

1. Connect the VTX and the power of the goggles.
2. Wait for the VTX to initialize and the green light flashes, and the status icon appears on the goggles.
3. Press the link button of the VTX and goggles respectively (as shown in the picture), when the VTX enters the pairing state The indicator light turns red, and the goggles end is a DI… DI… DI…
4. After the link is successful, the indicator light on the VTX turns solid green, the beeping sound on the goggles stops and the screen is displayed.

Upgrade

Please go to the official website to download the upgrade firmware, Avatar_ Sky X.X.X.img is the VTX file, Avatar_Gnd_X.X.X.img is the goggles file, copy it to the VTX or SD card, be careful not to change the file name. You need to turn on the power to use the U disk function.

1. Copy the upgrade file to the root directory of the VTX and the goggles, connect to the power supply and wait for the device to initialize (delete the old firmware file first if there in one).
2. Press and hold the link button on the VTX and the goggles for 8 seconds, the indicator light flashes red when the VTX enters the upgrade state, and the goggles automatically restarts and emits a beep…beep…beeper sound. (Do not power off during the upgrade process, the upgrade time on the goggle is about 6 minutes)
3. After the upgrade is successful, the indicator light of the VTX turns green and flashes, and the beeping sound stops after the goggles beeps for 5 seconds.

Please use a fan for cooling with the VTX powered on

UART

The UART function enables the VTX communicate with the flight controller, allowing the VTX obtain the flight controller information. Take Betaflight Configurator as an example to introduce the UART setting method.

1. Solder the white and gray wires of the 6 pin cable to the flight controller (refer to the Connection page)
   

2. Connect the flight controller to the Betaflight Configurator, and open the corresponding UART port (Take UART1 as an example in the figure) Check the MSP switch and click Save.
   

3. Open the CLI command line and enter the content in red font
   “set osd_displayport_device = MSP”
   “set displayport_msp_serial = Y” (Where Y is one less than the number of the serial port. e.g. Y = 2 for serial 3)
   “save

Status Indication

Goggles Buzzer Status

Link state| DI….DI….D1….
upgrade firmware| DI………. DI………. DI………. DI—
Upgrade failed| DI..DI..D1..
VTX Indicator Status
Link state| Steady red light
upgrade firmware| Red light rapidly flashes
Wireless connection, image output is normal| Steady green light
Wireless not connected| green light rapidly flashes
Wireless connection is normal, but the image is abnormal| green light slowly flashes

Operating Channel

Central frequency(MHz)| Channell| Channel2| Channel3| Channel4| Channels| Channel6| Channel7| Channel8
---|---|---|---|---|---|---|---|---
FCC| 5660| 5695| 5735| 5770| 5805| 5878| 5914| 5839
CE/SRRC| 5735| 5770| 5805| –| –| | –| 5839
MIC| 5660| 5700| –| –| –| –| –| 5745

Make sure you fully understand and abide by local laws and regulations before using this product. An amateur radio license may be needed in FCC regions when using channels 1,2,6or 7, as they are amateur frequency bands. Users who use the amateur frequency bands with a modified or cracked version or without a license may be punished for breaking local laws or regulations.

VTX Specification

SRRC: <20dBm; MIC: <25dBm
I/O Interface| JST1.06(Power in) JST1.04(USB)
Mounting Holes| 25.525.5 mm
Dimensions| 3333*6.5 mm
Storage| 8 G
Recording| 1080p/720p
Weight| 6.8 g
Operating Temperature| —20-40°C
Channels| 8
Wide Power Input| 3.1V-5V
Supported FC System| Betaflight
Bitrate| 25mbps / 50mbps
OSD| Canvas mode
Latency| Average delay 22ms
Antenna| IPEX

Camera parameters

VTX Antenna

WALKSNAIL Support
email: support@walksnail.com This content is subject to change. Download the latest version from https://www.walksnail.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>