DO Intelligent ID115PLUS Smart Bracelet User Manual
- June 7, 2024
- DO Intelligent
Table of Contents
Thanks for choosing our device, please read the user guide carefully before using it.
Setting
Use VeryFitPro on iOS or Android smartphone to set the wristband as follows:
Note: hardware and system of devices should meet the requirements:
1. Download VeryFitPro
Search and download
Search and download “VeryFitPro” from the Apple Store or Android App store.
Scan the QR code and download
It probably has a problem to open the link with WeChat or other scan tools,
please copy the link and open it through browser.
2. Product activation and installation
The product must be activated by charging before initial use, and then charge
the product to ensure normal power supply. The hand ring will automatically
power on.
Take out Pull open the strap and take out the bracelet body
Charge the battery: Insert the chip-mounted end of the bracelet body into the USB interface to activate the product by charging (be cautious not to reverse the polarity, and comply with the required voltage and current: 5V /500mA)
Installation: Mount the bracelet body into the slot of the wrist strap.
Wear on: Adjust the length of the wrist strap until it is appropriate to wear on the wirst.
3. Touch key
Single dick the touch key: Interface smith Press and hold the touch key: Enter
4. Make sure the Bluetooth of smart phone is ON, open app”VeryFitPro”
When selecting the right band from the search list, please slide the screen of wristband to wake up the device and then complete connecting.
Know your Device
1. Wearing Method
Wear the device on your wrist horizontally, about 2cm to carpal, the same
method as wearing watches.
2. Heart Rate Monitoring
To monitor Heart Rate more accurately, please wear the device on the upper
position of your wrist and a bit tighter than usual when you are taking
exercise.
3. Heart Rate Monitoring
Automatic heart rate Monitoring is ON as default, monitor Heart Rate all the
day automatically.
4. Interface Click the touch key to display successively
Function Introduction
1.1 Time Mode
Instructions Time dial can be switched as follows: APP Devices Mode>More
[Click the touch key) to enter the next mode: Data Mode ( you can customize
the shortcut through the app)
1.2 Data Mode
(Click the touch key) to enter the next mode: Heart Rate Mode [Press and hold
the touch key for 2s) to enter the sub-mode of Data Reading’
1.2.1 Data Reading Sub-Mode
[Crick the touch key] to enter the next sub-mode
Note: To go back to the Data Reading Mode by clicking the touch key on the
final interface of Data Reading Sub-Mode
1.3 Heart Rate Mode
Note: Upon staying at the Heart Rate interface for ls, start to monitor the
heart rate, and a fig. like —4—is displayed before the correct data is
monitored, and upon the cured data being monitored. data is displayed. [Click
the touch key] to enter the next mode: Alarm Clock Mode
1.4 Alarm Clock Mode
Note : Alarm clock function should be turned on in App for the alarm dock to be displayed.
[Click the touch key] to enter the next mode: Sports Mode [Press and hold the touch key for 2s] to start/dose alarm clock
1.5 Sports Mode
[Press and hold the touch key for 2s) to enter the Sports Mode lack the touch
key] to enter the next sports mode: and in case there are no other sports
modes. it wit go back to the time mode. Note: Types of Sports mode can be
selected in App (App can handle 4 types of track recording sports and 10 types
of other activities)
1.5.1 Sports Start Mode
After the countdown interface of 3-2-1-GO is the sports underway mode.
1.5.2 Sports Underway Mode
[Click the touch key) to enter the next sub-mode of ‘Sports Underway”(Press
and hold the touch key for 2s) to enter any interface of Data Reading, press
and hold 2s to exit the sports mode.
Note: The speed and distance of riding can be displayed, but App need to be
connected and the riding and App needs to start at the same time.
1.5.3 Sports Stop Mode
- It the sports last less than 1 minute, the user will be reminded of not saving the data.
(Click the touch key) to enter the main interface of sports mode (the data reading interface of sports data display mode is not displayed)
- If the sports last more than 1 minute, the Sports End Reminder will be displayed
(Click the touch key) to enter the sports data display mode
3) Sports data display mode
[Click the touch key] to enter the next sports data display mode, and the
single click of the final interface will go back to the first interface of
sports mode.
1.5.4 Event Reminder in Sports Mode
1) Reminder of exiting from sports mode upon a period of no activity
(Click the touch key] to remove the reminder of automatic quitting from sports
mode.
Note
1. Ifthere is no any activity in a period (15 minutes), reminder will be
displayed 15s before it stop.
2. New activities will remove the reminder of automatic quitting from the
sports mode.
3 .If there are no any new operations before the end of the countdown of
automatic quitting from the sports mode, it will exit from the sports mode.
2) Reminder of full-ram force quit
[Click the touch key) to confirm the full-ram Force Quit
Note : When the memory of wrist strap is full of sports data, the user
will be reminded of exiling from the Sports Mode
3) Reminder of force quit for low-battery
[Click the touch key] to accept the force quit from the sports mode
Note: During the sports activities, when the power is too low, the sport mode
will pause, and remind the user of force quit from the sports mode.
4) Reminder of inaccessible sport mode for low-battery
[Click the touch key] to accept the inaccessible sports mode for low-battery
Note: The reminder will occur when a user tried to start the sports mode with
the battery of device is in low.
1.5.5 Abnormal operations during the The reminder will be available soon
[Click the touch key] to quit from the reminder waiting mode
1. Camera mode control
Entry mode: Start the camera entry by Apo, and the device will get in the
camera mode successfully.
Photo taking methods: shake/wrist lifting/click the touch key
Modes of exit:
1. Press and hold the touch key to exit from the camera mode
2. Exit through App will make the wrist strap quit from the camera mode.
2. More modes of reminders
- Call Reminder
Click the touch key to remove the call reminder Press and hold the touch key
to hang up the call
Note: The call reminder in the App needs to be set open.
2) Message Reminder
In case of pages of messages, Click the touch key to read the remained ones.
Note : The relevant settings need to done in the App.
3) Alam Clock
Alam Clock: The relevant settings need to done in the App.
Alam Clock Types:
4) Long Sitting Reminder
Alam Clook Reminder: The relevant settings need to done in the App. Click the touch key: It will remove the reminder.
5) Target completion reminder
When some goals are achiveved, shake the wrist strap to get the interface of target completion reminder displayed click the touch key to quit from the reminder.
6) Low battery reminder
Low-Battery! Please recharge timely!
7) Device Error Notification
Note: When the device is detected with an abnormality. the interface herein
will be displayed each time the device is opened.
Status Code:
-01 means the abnormality of acceleration sensor
-02 means the abnormality of heart rate sensor
-03 means the abnormality of touch key IC
-04 means the abnormality of flash
Basic Specifications
Model No.: ID115Plus HR
Battery Capacity: 65mAh
Working Voltage: 3.7y
Host weight: about 24g
Sync: Bluetooth 4.2
Working temperature: -20 C- 45 C
Working Time: 7days
Product frequency band: 2402-2480MHz
Maximum transmit power -1.07dBm (for EU compliance)
Declaration of toxic and hazardous substances in electronic information
products
The device meets the EU ROHS criterion. Please refer to IEC 62321, EU ROHS
Directive 2011/65/EU and revised directive.
Wearing and Maintenance
Our products are designed for you to wear throughout the day. So please follow a few brief instructions when you are wearing and maintaining your smart devices. To keep your wristband clean and your skin comfortable, we put forward the following tips:
- Regularly clean your wrist and the smart wristband. especially after sweating in the exercise or being exposed to substances such as soap or detergent which may attach on the internal side of the wristband.
- Do not wash the wristband with household cleanser. Please use soapless detergent, rinse thoroughly and wipe with a piece of soft towel or napkin.
- For spots or stains that are not easy to remove, scrub with alcohol and then follow the above steps.
FAQ
♦ Failed to find the device when pairing
(1) Make sure the Bluetooth of smart phone is ON, and smart phone OS Android
4.4 & Above, iOS 8.0 & Above.
(2) Make sure the distance between phone and device Is within 0.5meter, device
is among the normal Bluetooth communication distance range(within lOmeter)
after pairing finished.
(3) Make sure the device is not under low battery. If there is still a problem
after fully charged, please contact us.
♦ Failed to connect with Bluetooth occasionally
(1) Caused by the abnormality of Bluetooth service when it restarted on the
phone.
(2) Reboot mobile phone or re-start the Bluetooth service, then it works
normal.
♦ How to restore factory defaults
Make sure the device is connected with smart phone, go in the App, enter
“device– System setting”, and choose “reboot device”.
Caution :
- If you experience skin irritation when wearing your watch, please refrain from wearing, and wait two to three days to see if your symptoms ease. If symptoms persist or worsen, please consult a physician.
- If you have eczema, allergies or asthma, you may be more likely to experience a skin irritation or allergy from a wearable device.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE DISPOSE OF USED
BATTERIES ACCORDING TO THE INSTRUC11ONS
Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substances.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>