24″ Dumor Rabbit Cage Starter Kit User Manual

June 7, 2024
DUMOR

Dumor Logo

SKU#:1457225
24″ Dumor Rabbit Cage Starter Kit Assembly Manual
(Pictures may vary slightly from actual product)

24 Dumor Rabbit Cage Starter Kit

PARTS LIST

Part# Description Image Quantity
1 24″ Cage ![Repeat Step 2 for the remaining side

panels](https://manuals.plus/wp-content/uploads/2021/05/Repeat-Step-2-for-the- remaining-side-panels-1568x1413.jpg)| 1 pc
2| 24″ Dropping Pan| 24 Dumor Rabbit Cage Starter Kit - Dropping
Pan| 1 pc
3| Metal Feeder| 24 Dumor Rabbit Cage Starter Kit - Metal
Feeder| 1 pc
4| Water Bottle| 24 Dumor Rabbit Cage Starter Kit - Water
Bottle| 1 pc
5| 24″ Vertical frame legs| 24 Dumor Rabbit Cage Starter Kit - Vertical
frame legs| 4 pcs
6| Horizontal dropping pan supports| 24 Dumor Rabbit Cage Starter Kit -
Horizontal dropping pan supports| 2 pcs
7| Stacking Lugs| 24 Dumor Rabbit Cage Starter Kit - Stacking
Lugs| 4 pcs (only used if stacking for more cages)
8| Nuts & Bolts| 24 Dumor Rabbit Cage Starter Kit - Nuts &
Bolts| 12 NUTS and 12 BOLTS

ASSEMBLY INSTRUCTIONS

Step 1. Rabbit Cage Set Up
1. Take the folded cage out of the carton and put it on a flat surface. Remove the top panel and make sure the door on the front panel is closed to keep the cage secure during assembly.

24 Dumor Rabbit Cage Starter Kit - Rabbit Cage Set Up

2. Grab any two adjacent side panels and slide the vertical panel into the side hooks until secure.

Grab any two adjacent side panels

3. Repeat Step 2 for the remaining side panels. You should now have all sides of the cage assembled.

24 Dumor Rabbit Cage Starter Kit - Cage

Step 2. Frame Legs Set Up
1. Lay the cage on its side and attach the vertical frame legs to the two horizontal plates on each side of the cage. There should be an extra hole at the bottom of the vertical frame leg that will be used to attach the horizontal dropping pan supports. Secure with two nuts and bolts per side. The head of the bolt will be on the outside of the cage.

Lay the cage on its side

2. Repeat Step 1 for the remaining vertical frame legs.

Repeat Step 1 for the remaining vertical frame legs

3. Gently, flip the cage upside down and attach the horizontal dropping pan supports on the inside of the vertical frame legs. Bolt the supports through the vertical frame legs from the same direction as the vertical frame legs.

Gently, flip the cage upside down

4. Turn the cage upright and place the top panel on the cage and secure the top panel with the hooks on all for sides.

Turn the cage upright and place the top panel

Step 3. Dropping Pan, Metal Feeder and Water Bottle Set Up

Dropping Pan:
Slide the dropping pan into the horizontal dropping pan supports until centered underneath the cage.

Slide the dropping pan into the horizontal dropping
pan

Water Bottle:
1. Determine the proper height for the drinking nozzle for your pet.
2. Hang the metal water bottle support on the appropriate horizontal wire to maintain the desired height for drinking.
3. Fill the bottle with water to desired amount, secure lid and attach nozzle.
4. Place water bottle nozzle down into the water bottle support. The bottle must be set completely vertical to allow proper nozzle ball seating in order to prevent leaks.

Place water bottle nozzle down into the water bottle

Metal Feeder:
1.To install the rabbit feeder a small opening must be cut on one side of the cage. The bottom chute of the feeder requires a 6.25”(L) X 2”(W) opening. Determine a desired placement of the feeder. It should be low enough so rabbit can reach it comfortably.

To install the rabbit feeder

2. With small wire cutters (not supplied) cut one adjacent horizontal wire and one adjacent vertical wire close to the outer wires to the 6.25″ (L) X 2″(W) opening.  Remove all sharp edges after cutting to prevent injury to the rabbit. Slide the bottom spout of feeder through the opening and push the wireframe through the mesh. The hook of the wire should go through two horizontal wires of the mesh.

small wire cutters

Step 4. You can stack 2 cages on top of each other using the four stacking lugs. Insert 1 stacking lug in each frame leg-gently place additional cage on top and secure.

You can stack 2 cages on top of each

Assembly time: 15 minutes
Required for Assembly: 1 person
Tools required: 2 small adjustable wrenches or 2 – 10 mm wrenches and 1 small wire cutter

Distributed by:
TRACTOR SUPPLY COMPANY
5401 VIRGINIA WAY
BRENTWOOD, TN 37027
For customer support,
call: 1-888-376-9601
www.TractorSupply.com
MADE IN VIETNAM

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals