edelkrone sliderplus v5 pro User Manual

edelkrone sliderplus v5 pro

WHAT’S IN THE BOX & THE BASICS

1. Rubber feet
2. Built-in foldable legs
3. Magnetic belt clip slot
4. 3/8”-16 pop-up screw
5. 1/4” mounting port
6. Instant locking mechanism
7. Incline
8. Mounting wheel for 3/8”-16 mounting port
9. Cleaning kit (x3)
10. 2.5mm-3mm allen keys
11. Motion control belt (x2)
12. Manual control belt (x2)

ATTACHING THE BELTS & TENSION ADJUSTMENT

1. Attach either the Manuel control belt or the motion control belt depending on use.
   

2. Remove the wheel.

3. Pass the belt through the hole.

4. Attach the wheel back.

1. Attach the other head of belt
   

2. If belt tension is low, you may increase it by loosening the side wall screws and pulling out the side walls until desired tension is achieved.

LEG & ANGLE ADJUSTMENT

To adjust the legs:

1. Loosen the wheel by turning it counterclockwise.

2. Legs are adjustable at each 15°. Adjust the leg at an appropriate angle

3. Tighten the wheel by turning it clockwise.

MOUNTING YOUR SLIDERPLUS TO YOUR TRIPOD

1. Detach tripod head from your tripod
   

2. Place your SliderPLUS onto your tripod’s 3/8”-16 mounting screw.

3. Mount using the mounting wheel.

MOUNTING YOUR CAMERA TO YOUR SLIDERPLUS

1. SliderPLUS has 3/8”-16 screw for your tripod head hidden inside. You can access this screw with the help of a coin. Using a coin, turn the screw until it pops out. To hide the screw back again just press it down and turn it counter clockwise.
2. Place your tripod head on the screw and tighten clockwise.
3. Attach your camera to your tripod head

MOUNTING YOUR MAGIC ARM ON SLIDERPLUS

1. You can mount any camera head or arm to your SliderPLUS with 1/4” mounting screw.

INCLINED MOTION

To get inclined shots

1. Place your SliderPLUS onto 3/8”-16 mounting screw of your tripod head.
2. Attach your FlexTILT Head or any camera head onto your SliderPLUS.
3. You should attach your Slide Module to incline side of the SliderPLUS.
4. You should tighten the slide tension of the Slide Module to get inclined motion.
5. Place your camera to FlexTILT Head or any camera head.
   ! If you are not able to slide manually after inclined operation, try loosening the tension. Make as small adjustments as possible.
   ! Please make sure that your tripod legs are opened widely enough to prevent falls and balance issues.

CLEANING KIT

1. Separate the slider upper and lower carriages while your slider is resting on a flat surface as shown.
2. Remove a double sided sticker from the cleaning kit.
3. Stick one side of sticker on slider rail as shown and peel off the white cover from the sticker.
4. Slide the slider cars from one end to the other to clean the wheels.
5. Repeat this process for all wheels.

CAUTIONS AND TIPS

Please contact our dedicated customer care team for recommended tripod legs.

1. In order to get perfect results with you SliderPLUS please attach your SliderPLUS directly to tripod legs, not to tripod head.

2. If your tripod has a feature that allows you to extend the height from its neck, we suggest keeping it down and as tight as possible in order to prevent a rainbow effect.

3. Please make sure that your SliderPLUS withstands within the area of the tripod legs to prevent falls and balance issues. Always make sure that your system is leveled and balanced.

4. Always keep your slider locked while it is not in use.

5. Use built-in foldable legs to level your system.

SliderPLUS can travel twice its own length when it’s mounted on a tripod.
When using it on its feet, it can only travel its own length.

For more tips please watch the user’s manual videos at: http://edel.kr/sld5

DISCLAIMER
edelkrone cannot be held responsible for damage caused by improper use or modification of the product

For more information and tips about your SliderPLUS, please watch the user’s manual videos at: http://edel.kr/sld5

http://edel.kr/sld5

References

• SliderPLUS v5 - Setup & Recommended Use - YouTube
• edelkrone - Official Site

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>