Vasco D13 Controlled Ventilation System Instruction Manual
- June 8, 2024
- Vasco
Table of Contents
Vasco D13 Controlled Ventilation System
Product Information
Specifications
- Product Name : Bluetooth Board for Controlled Ventilation
- Model : PCB Bluetooth
- Use: Controlled ventilation of residential buildings
- Power Requirements : 12V and 230V sections
- Manufacturer’s Warranty: Check manual for details
Product Usage Instructions
Installation
- Remove the cover from the frame of the inside cover.
- Remove the left plastic cover to access the 12V section by releasing the snap-in at the top left.
- Press and hold the button on the board for 10 seconds to remove the device from the mesh network.
- Disconnect the device from the power supply by turning off the fuse for the circuit.
- Remove the right plastic cover to access the 230V section by loosening the center screw and pulling it off.
- If a sensor is installed, remove it by pulling it off the circuit board. Disconnect fan and power cables.
- Carefully loosen the circuit board at the upper snap-in hook and tilt it forward to remove it.
Safety Precautions
Always follow the manufacturer’s instructions and use recommended components. Modifications are prohibited. Disconnect power before any maintenance tasks.
Maintenance
Regularly check for dust accumulation and clean if necessary. Ensure proper ventilation for optimal performance.
FAQ
- Q: Can I use this product in commercial buildings?
- A: No, this product is designed for residential buildings only.
- Q: How do I reset the Bluetooth connection?
- A: Press and hold the button on the board for 10 seconds to remove the device from the mesh network.
- Q: What should I do if the LED does not flash red during removal?
- A: Refer to the manual of the functional unit for troubleshooting steps.
GENERAL INFORMATION
Observe and follow the warnings in the applicable instructions.
Non-compliance with the warnings can lead to injuries or damage!
- Carefully read and follow the instructions before installation or use!
- Keep instructions safe for future reference!
- Installation may only be carried out by experienced and qualified professionals who are familiar with the installation of ventilation products!
- Electrical installation may only be carried out by professionals who are qualified in the field of electrotechnical systems!
- Ensure that the fastening is secure and that loading capacity and statics are sufficient. Use fastening material that corresponds to the wall types.
- After receiving the product, please unpack it carefully and check for any possible damage in transit. A damaged product must not be installed or used.
- When using accessories or third-party products, follow the manufacturing instructions and ensure the suitability of products.
intended use
The product is designed for controlled ventilation of residential buildings. It can be installed in new buildings or retrofitted to existing buildings undergoing renovation and modernization work.
Use of the product is permitted only in conjunction with the components recommended by the manufacturer.
Modifications to the product or system are prohibited.
Any other use is considered improper. Resulting damages are excluded from the liability
warranty
The manufacturer does not accept any warranty claims in the cases of:
- Non-compliance with the instructions.
- Damage resulting from incorrect installation.
- Any form of independent modifications to the product.
EXPLANATION OF SYMBOLS
INSTALLATION
Remove the cover from the frame of the inside cover. 
Remove the left plastic cover to gain access to the 12 V section of the inside
cover. Do this by releasing the snap-in at the top left. 
Press and hold the button on the board for 10 seconds to remove the device
from the mesh. The LED will flash red 3 times to confirm the removal. For more
information on removing devices from the mesh, refer to the manual of the
functional unit. 
Before carrying out any further steps, disconnect the device from the power supply by turning off the fuse for the circuit. This should only be done by trained professionals.
Remove the right plastic cover to gain access to the 230 V section of the
inside cover. To do this, loosen the center screw and pull it off the frame
along with the plastic cover. 
Remove the sensor (1) , if it is installed, by pulling it off the circuit board. Also, disconnect the fan cable (2) on the left side and the power cable (3) on the right side from the board.
Remove the circuit board by carefully loosening it at the upper snap-in hook
and tilting it slightly forward. It can then be removed. 
Insert the new board into the frame‘s holder by inserting it into the lower
snap-in hooks and then carefully tipping it backwards so that it also snaps
into place behind the upper snap-in hook. 
Take over the setting of the DIP switch from the old board. For more
information on configuring the DIP switch, use the illustration on the left-
hand side of the circuit board or the operating instructions of the functional
unit. 
Now reinstall the sensor (1) if it was used before. Then connect the fan cable
(2) and the power cable (3) to the new board. 
Install the right plastic cover of the 230 V section and tighten the center
screw of the plastic cover. 
Now turn the power of the device back on to proceed with the setup of the new
board. 
Add the unit with the new board to the existing mesh according to the
instructions in the functional unit manual. 
Once the device is successfully integrated into the mesh, the left plastic
cover of the 12 V section can be installed. Insert the cover at the bottom and
make sure that the upper snap-in hook engages. 
Install the cover onto the frame of the inside cover. Make sure that the snap- in hooks of the cover engage correctly.
Technical changes reserved. For current status see manufacturer’s homepage.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>