NOCH Gras-Master Instruction Manual
- June 7, 2024
- NOCH
Table of Contents
NOCH Gras-Master
Thank you for purchasing the NOCH Gras-Master 3.0 PROFI.
This third generation of the NOCH flocking device makes it possible for you to
achieve better and more realistic results in creating meadows and patches of
grass.
And it works that simple:
- The ground to be flocked with grass is coated with special NOCH Grass Glue (ref. 61130 or 61131).
- The grass fibers are loaded into the grass container. Different lengths and colours can thus be mixed together.
- The crocodile clip (counter-pole) is fastened near the surface where the grass is to be applied.
- Due to the electrostatic charge, the grass fibers stand vertically in the glue bed.
Find application possibilities, recipes and ideas for your model landscape design on www.noch.com and on the YouTube channel www.noch.de/youtube
Brush some NOCH Grass Glue, item no. 61130 or the NOCH Grass Glue XL, item no. 61131, onto the area that you want to flock with grass. Fill the grass drum of the Gras-Master 3.0 PROFI maximally 2/3 full with NOCH Grass. Depending on the length of the grass fibres choose the suitable sieve. The fine sieve can be used for 1.5 mm to 2.5 mm grass and for snowflakes. The medium sieve is appropriate for grass fibres of 2.5 mm to 6 mm length (Scatter Grass, Master Grass Blends, Wild Grass). The coarse sieve is to use for 6 mm to 12 mm long fibres (Wild Grass and Wild Grass XL). These are recommendations and may be adjusted by yourself according to your requirements. Now attach the alligator clip to the landscape in the area that you want to cover with grass. For this purpose you can use a small nail or a fixing pin. Switch on the Gras-Master 3.0 PROFI (the red LED lamp is on) and gently shake the device over the area covered with grass glue. After the glue has dried you can vacuum off the loose grass fibres and apply them later again. When you finished your work, always switch the Gras-Master 3.0 PROFI off (the LED lamp goes out).
Contents:
Gras-Master 3.0 PROFI, counter pole with crocodile clip, three sieves for
flocking grass fibres of different lengths, eight 1.5 V AA batteries.
Function:
The centrepiece of the Gras-Master 3.0 PROFI is an electron-ic circuit
transforming the 12 V voltage of the batteries into a stable, negative high
voltage of up to approx. 16 kV DC. The bottom of the grass container is coated
with a conductive special varnish. This layer is connected with the high
voltage (up to approximately 16 kV), while the earth (0 V) is connected to the
earth cable.
During operation, a strong electric field is formed between the high voltage
and the earth. The grass fibres are negatively charged in the container by the
escaping electrons. After passing through the sieve, the fibres are attracted
by the substrate surface connected to the earth, where, after adhering to the
previously applied adhesive layer, they align themselves vertically due to the
electric field. Therefore an electrically conductive substrate is necessary
for a
good function, which is achieved by the conductive special adhesive. Even
after switching off the device the high voltage is still present for a short
time. Therefore do not touch the bottom of the grass container, not even when
removing the remaining material. Due to the special construction that is
protected as registered design, a minimum power consumption and a maximum of
safety is achieved.
Technical data:
Operating voltage: 12 V
Power consumption: approx. 220 mA
Output voltage : up to approx. 16 kV
Power supply: 8 x 1.5 V AA batteries, alkaline
Operating time: approx. 10-12 h
Function indication by red LED On/Off switch
Safety Instructions:
Proper use
This product is a scale modelling article aimed at ambitious modellers, and no
toy. It is designed for use on a model layout. It must exclusively intended to
be operated together with the accessories recommended by NOCH. Basically, NOCH
products are developed and designed for the hobby sector and not for permanent
operation. This product is intended for use at room temperature and humidity.
Please operate the product only indoors, and avoid any atmospheric influences.
Any other use will be considered not to be in conformity with the proper use
or intended purpose. NOCH GmbH & Co. KG will assume no responsibility for any
damage or defect resulting from improper use or the non-observance of the
directions given in the instruction manual.
Operating and storage conditions
- Observe the following operating conditions: 15 °C – 40 °C, up to 75 % relative humidity, do not allow the formation of dew.
- Observe the following storage conditions: 10 °C – 60 °C, up to 85 % relative humidity, do not allow the formation of dew.
General safety recommendations (for your safety)
- Carefully read through the instruction manual before use.
- Pay attention to the safety recommendations and warnings given in the instruction manual or provided on the product.
- Always retain the instruction manual available near to the product itself.
- Hand over the product to third persons only together with the instruction manual.
- Operate the product only when it is in perfect condition.
- It is absolutely necessary to keep this product and all accessories (adhesives, paints, knives, etc.) out of the reach of children.
- Let children use the product only under the supervision of adults.
- This product may be used by children or persons with reduced psychic, sensory or mental capabilities, or by per-sons lacking experience or knowledge if they work under supervision or have been instructed in the safe use of the product, and understand the hazards resulting from such activity. Cleaning and maintenance may not be carried out by children without the supervision of adults.
- Inform children of the contents of the instruction manual, if necessary, and of the potential hazards related to the use of the product.
- Children must not play with the product.
- The product must not be operated when persons with pacemakers are present.
- Wash your hands and clean your tools after using the product.
- Do not eat, drink or smoke while using the product.
Disruption hazard
Devices without tested electromagnetic compatibility may cause failures and
malfunctions. Do not operate any device that was not tested near the plant.
Overload hazard
Operating the product with the wrong power pack may result in property damage.
Explosion hazard
Operating the product in explosive environments or with unsuitable batteries
may trigger explosions and cause severe injuries and property damage. Do not
operate the product in explosive environments.
Fire hazard
Using the product with faulty or old batteries or in permanent operation may
trigger a fire or generate smoke.
- Do not operate the product while it is unattended.
- Before prolonged storage, remove the battery from the device due to the risk of leakage.
- Immediately disconnect the product from the power supply if smoke or a scorching smell is generated.
Corrosion hazard / Risk of short circuits
- Using the product in moist rooms or any contact of the product with water may cause short circuits and property damage.
- Use only in dry rooms.
- Avoid any contact with water or other liquids.
Risk of physical injury and property damage
Improper use of the product may cause physical injury and property damage.
Electric shock harzard
Avoid danger to life through electric shock.
- Never touch the bottom of the flock container when the device is in operation.
- Never operate a damaged product.
- Never open and repair the product yourself. Do not make any changes to the product that are not described in the operating instructions. The product contains current-carry-ing parts. There is danger to life after opening the product. Repairs may only be carried out by NOCH.
Environmentally friendly disposal (WEEE)
Products that are labeled with the symbol of a crossed dustbin must not, at
the end of their life span, be disposed of with common household waste, but
must be handed over to a collecting point that recycles electrical and
electronic equipment. The symbol on the product, in the instruction manual or
on the packaging calls the user‘s attention to such obligation. All materials
used are recyclable according to their marking. When allowing recycling, the
reutilization of materials, or any other form of recycling used equipment, you
will make a valuable contribution to the protection of our environment. Please
enquire from your local authorities which disposal companies are relevant in
your vicinity.
- Please observe the local regulations regarding waste disposal.
- Please observe the WEEE directive in the version currently applicable.
- Remove any batteries from the product before scrapping it.
Suitable accessories:
Sieves Set, 3 parts
The Sieves Set contains one fine, one medium and one coarse sieve.
The rule of thumb is: the shorter the grass fibre, the finer the sieve. The
fine sieve can be used for 1.5 mm to 2.5 mm grass and for snowflakes. The
medium sieve is appropriate for grass fibres of 2.5 mm to 6 mm length. The
coarse sieve is to use for 6 mm to 12 mm long fibres.
But dare to experiment, too: If you place long grass fibres in the medium sieve, fewer fibres will reach the ground. Dry, sparse meadows can be depicted in this way, or different grass fibres can be carefully mixed together on the substrate. There’s no limit to your imagination!
60114 Sieves Set, 3 parts: each 1 sieve fine, medium and coarse for the Gras-Master 3.0 and the Gras-Master 3.0 PROFI
Grass Flocking Templates, 5 pieces
With the templates you can quite easily design partially covered areas. The
results are edges, tufts, stripes, areas and various patches of grass.
You can use the templates in two ways:
Either you apply Grass Glue (ref. 61130 or 61131) onto the substrate first,
loosely hold the template over it and then flock through the gap onto the wet
glue. Or you can spray Spray Glue “Haftfix” (ref. 61151, see below) onto a
surface using a template resting on the substrate. You can then flock without
holding the template. Individual gaps in the templates can be blocked with
masking tape. Again: Dare to experiment!
Grass Glue
The NOCH Grass Glue was specifically designed for the electromagnetic flocking. In comparison with conventional adhesive and wood glue it has the following features and advantages:
- perfect consistency: it is easy to spread without running
- it sets slowly: You can flock your areas without time pressure, so there are no “bare” spots in your meadow
- it dries out perfectly transparent: no white streaks
- it has a high adhesive strength: the adhesive strength is significantly stronger than, for example, diluted wood glue
Spray Glue “Haftfix”
The universal Spray Glue is suitable for all types of glueing tasks – for
modelling as well as around the home.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>