PCW3000
PCW5000/HS
USER GUIDE

Operating/safety Instructions
www.portablewinch.com

FRENCH IS THE ORIGINAL
LANGUAGE OF THIS DOCUMENT

INTRODUCTION

Portable Winch Co. thanks you for purchasing a Portable Capstan
Winch TM. This manual was written to help you make the best use of your new machine and to use it in the most secure way.

PLEASE READ CAREFULLY BEFORE USE
For any problems or questions please refer to an authorized Portable Winch Co. dealer or contact us directly.

Safety guidelines

Portable Capstan WinchesTM is designed to pull non-rolling objects , generally at angles of more or less 45 degrees relative to the horizontal. The use of a winch may present serious risks of injury,  property damage, or even death.

DO NOT UNDERESTIMATE THE POTENTIAL DANGERS

1.1 Safety messages.

Your safety and the safety of others are very important. You will find important safety messages in this manual. Please read them carefully.
These safety messages are warning you of potential injuries to either yourself or others. Each safety message is preceded by a warning symbol.

| YOU WILL BE MORTALLY OR SEVERELY INJURED IF YOU  DO NOT FOLLOW THESE INSTRUCTIONS.
| YOU COULD BE MORTALLY OR INJURED IF YOU DO NOT FOLLOW THESE INSTRUCTIONS.
| YOU COULD BE INJURED IF YOU DO NOT FOLLOW THESE INSTRUCTIONS.
| READ THE USER GUIDE.
| EYE AND HEARING PROTECTION.

1.2  Labels

1.2.1 Serial number labels
The serial number label can be found on the right side of the machine’s gearbox. In addition to the serial number, the fundamental specifications of your model are also found there.

1.2.2 Noise protection label

We recommend that you wear hearing protection during use of the Portable Capstan Pull WinchTM.
1.2.3 Line installation label
The label is placed on the housing. This label is placed on the winch’s housing. It indicates the installation direction of the line for the Portable Capstan WinchTM.
1.3 Safety information.
DO NOT ALLOW CHILDREN TO USE THE PORTABLE CAPSTAN WINCHTM. KEEP CHILDREN AND ANIMALS OUTSIDE OF THE WORK  ZONE.

NEVER ALLOW AN UNTRAINED PERSON TO USE THE PORTABLE CAPSTAN WINCHTM. MAKE SURE THAT THIS PERSON IS AWARE OF  THE SAFETY INSTRUCTIONS AND HAS READ THIS MANUAL AS WELL AS THE HONDA ENGINE USER MANUAL.

INFORM ALL USERS OF THE SAFETY AND USAGE
INSTRUCTIONS.

FAMILIARISE YOURSELF WITH THE OPERATION OF THE PRODUCT AND THE SAFETY INSTRUCTIONS BEFORE YOU START TO WORK  WITH THE PORTABLE CAPSTAN WINCHTM.

ENSURE THAT YOUR CLOTHING IS CLEAR FROM THE MOVING PARTS OF THE MACHINE..

THE ENGINE EXHAUST GASES CONTAIN POISONOUS CARBON MONOXIDE. NEVER RUN THE ENGINE IN A CLOSED BUILDING WITHOUT ADEQUATE VENTILATION.

CLEAN AND/OR REPLACE ALL SECURITY LABELS THAT ARE DIRTY, DETERIORATED, UNREADABLE, OR TORN

ALWAYS KEEP ONLOOKERS OUTSIDE OF THE WORK ZONE.

NEVER PULL ROLLING MATERIAL THAT RISKS ROLLING OUT OF YOUR CONTROL.

THE PORTABLE CAPSTAN WINCHTM IS NOT DESIGNED TO LIFT LOADS OR PEOPLE.

WE RECOMMEND THAT YOU WEAR HEARING PROTECTION DURING USE.

2 Checks before use.

2.1 On receiving
Inspect the box to detect any obvious damage. If a part is missing or damaged, notify the carrier immediately.
2.2 Is the engine ready?
2.2.1 Oil the engine
Fill the Honda engine with SAE 10W-30 API SJ oil according to the quantities indicated for your model.
● PCW3000: 100 ml
● PCW5000: 250 ml
● PCW5000-HS: 250 ml
Check the oil level on a horizontal surface. The oil level must reach the opening edge. For special uses and in extreme temperature conditions, consult the Honda engine manual.
2.2.2 Gasoline.
Fill the tank with UNLEADED gasoline. Never use a mixture of oil/gasoline, your Portable Capstan WinchTM is equipped with a four-stroke engine. Consult the Honda engine manual.
Do not overfill.
2.2.3 Starting the engine
Consult the Honda engine manual for starting instructions.
FIRST TIME USE: ALLOW THE ENGINE TO RUN IDLY FOR FIVE (5) MINUTES BEFORE PULLING A LOAD FOR THE FIRST TIME.
Activate the engine’s on/off switch.

Take care to pull the starter grip in the output axis of the rope. If you do not pull at the correct angle, the friction of the rope on the plastic housing may damage the rope and/or the housing.

2.2.4 Capstan drums Your Portable Capstan WinchTM is equipped with the following drums.

● PCW3000: Drum 76 mm in diameter.
● PCW5000: Drum 57 mm in diameter.
● PCW5000-HS: Drum 85 mm in diameter.

2.2.5 Spark arrestors

In some areas, an engine may not be used without spark arrestors. Check local regulations. The PCW3000 model is fitted with internal spark arrestors.

THE PCW5000 AND PCW5000-HS MODELS ARE NOT EQUIPPED WITH SPARK ARRESTORS.

• AN OPTIONAL SPARK ARRESTOR IS AVAILABLE FROM PORTABLE WINCH CO. AND FROM APPROVED HONDA DEALERS.
•  PART NO. FROM PORTABLE WINCH CO.: PCA-1151
•  PART NO. FROM HONDA: 350-2M7-801
  Consult the Honda engine manual for spark arrestor maintenance instructions.

Using the winch

MOST PULLING SITUATIONS PRESENT POTENTIAL DANGERS!

3.1 Rope
3.1.1 Type of rope

Only use a line with low elasticity. We recommend a double braid polyester line.
Min., max. and recommended diameters:
● PCW3000:

• *       * Min.: 10 mm

  • Max.: 12-13 mm
  •  Recommended: 10 mm

● PCW5000 and PCW5000-HS:

• *       * Min.: 10 mm

  • Max.: 16 mm
  • Recommended: 12-13 mm

Contact us if you have any questions about rope types.

Contact us if you have any questions about rope types.
DO NOT USE A 3-STRAND YELLOW POLYPROPYLENE LINE!

● POLYPROPYLENE AND POLYETHYLENE LINES ARE DANGEROUS FOR PULLING DUE TO THEIR ELASTICITY AND THEIR LOW MELTING POINT.
● MAKE SURE THAT THE LINE IS NOT DAMAGED AND OFFERS ADEQUATE RESISTANCE FOR THE LOAD TO BE PULLED.

STRETCHING = DANGER!

● STRETCHING THE LINE MAY CAUSE SERIOUS INJURY. BE CAREFUL WHEN RELEASING THE TENSION IN THE LINE.
● ALL LINES STRETCH INCREASED LENGTH: THE MORE THE LINE IS PULLED, THE MORE IT STRETCHES.
● STRETCHING THE LINE MAY CAUSE THE LOAD TO MOVE IN AN UNEXPECTED AND DANGEROUS MANNER.
● STRETCHING THE LINE MAY CAUSE IT TO RELAX AND MOVE BACKWARDS QUICKLY, PULLING YOUR HAND TOWARDS THE WINCH OR CAUSING SEVERE BURNS. NEVER WIND THE LINE AROUND YOUR HAND.

ALWAYS WEAR GLOVES.

3.1.2 Rope maintenance

PERFORM A VISUAL INSPECTION OF THE LINE BEFORE EACH USE. IF IT SHOWS OBVIOUS SIGNS OF WEAR (STRANDS CUT, EXCESSIVE ABRASION)  THEN CHANGE IT.
IF YOUR LINE IS DIRTY, CLEAN IT. A DIRTY LINE CAN QUICKLY BECOME DAMAGED AND CAUSE PREMATURE WEAR OF PARTS THAT COME INTO CONTACT WITH IT.

3.1.3 Recommended knots

You must attach the load to the end of the line. Although a simple knot may sometimes suffice, we recommend using a bowline knot (fig. 1). This knot holds approximately 70% of the line’s capacity while most knots reduce the line’s capacity by 50% or more. Additionally, it may be easy to untie even after pulling a heavy load.

Even better, a double bowline knot (fig. 2) allows you to maintain approx. 75% of the line’s capacity.

3.2 Anchoring the winch
OPTION 1: In most cases, the winch is anchored to a fixed object using a polyester sling or one of our optional anchors, and the line is attached to the object you are trying to move. The latter is moved towards the winch as the winch pulls the line.
OPTION 2: Sometimes, the winch can be anchored to the object you want to move and the line is attached to a fixed object. The winch and the object being moved are then pulled towards the line’s anchoring point. This method is useful when you guide the load while operating the winch. Your winch is supplied with a polyester sling measuring 2 meters. To anchor the winch, wind it around the anchoring point with the sling. Insert each end of the sling in each of the two safety hooks located on the back of the winch (fig. 1).
Place the winch in the direction of the load to be pulled. When the winch is switched on, it will attempt to align itself with the load. The friction of the sling against the anchor may prevent correct alignment; in this case, release the tension in the line and move the sling so that the tension is distributed over the two books equally.

WHAT NOT TO DO: WHEN YOU INSTALL THE SLING TO ANCHOR THE WINCH, AVOID A FULL TURN AROUND AN ANCHORING POINT (FIG, 2). THIS  WILL PREVENT THE WINCH FROM ALIGNING ITSELF WITH THE LOAD CORRECTLY. THIS WILL ALSO APPLY UNEVEN TENSION TO EACH OF THE  HOOKS.
AVOID INSTALLING THE SLING ON SHARP CORNERS WHICH ARE LIKELY TO DAMAGE THE POLYESTER SLING. WHEN YOU USE A POLE, A  TREE OR A STUMP AS AN ANCHORING POINT, INSTALL THE SLING CLOSE TO THE BASE.

ANCHORING AROUND A STUMP REQUIRES SPECIAL ATTENTION TO AVOID THE SLING SLIPPING OFF THE TOP OF THE STUMP.

ENSURE THAT THE ANCHORING POINT IS ABLE TO WITHSTAND THE WINCHING WITHOUT BREAKING, BEING EXTRACTED OR BECOMING  DAMAGED.

We also offer a wide range of anchoring accessories for our capstan winches. Visit www.portablewinch.com

3.3 Oil level
PCW5000 and PCW5000-HS: The Honda GXH-50 engine is fitted with an Oil Alert TM system that automatically shuts off the ignition when the oil level in the crankcase falls below a safe level.  The  Oil AlertTM system also stops the engine when the engine’s operating angle exceeds 20 degrees (± 4 degrees). Make sure that your installation keeps the winch relatively horizontal during pulling and when idling.
PCW3000: The Honda GX-35 4-stroke engine is an engine for all positions. Therefore, it can be used at any angle without the engine stopping during operation.
3.4 Installing the rope

THE CORRECT DIRECTION WHEN DEPLOYING THE LINE IS THE KEY TO THE SAFE USE OF THE WINCH.
The wide range of situations encountered during pulling prevents us from giving specific instructions for all situations; however, you should consider the following points:

3.4.1 Rope
Use a line with a low elasticity in good condition with a minimum diameter of 10 mm and a maximum diameter of 16 mm (or 12 -13 mm with the PCW3000) with good knots. We highly recommend the bowline knot (see section 3.1.3). Use pulleys to divert the line and increase the pulling power when the load approaches or exceeds the winch’s pulling capacity.
3.4.2 Pulley
The use of a pulley at a short distance from the winch offers several benefits:
● Provides an angle allowing the load to be slightly raised to reduce friction;
● Maintains the winch in a near-horizontal position;
● Keeps the winch and the operator away from the load’s trajectory.
3.4.3 Direction
Install the line so that it doesn’t rub against any objects during pulling. Try to install the line so that the front of the load is slightly raised. Never pull downwards or through obstacles.

IN GENERAL, IF THE LINE TOUCHES THE GROUND DURING PULLING THEN THE SETUP IS INCORRECT.

3.4.4 On a slope
DO NOT PULL A LOAD DOWN A SLOPE TOWARDS THE WINCH BECAUSE THE LOAD MAY SLIDE TOWARDS YOU BEFORE YOU CAN STOP IT. IN THIS CASE, USE A  PULLEY AT THE BOTTOM OF THE SLOPE AND POSITION THE WINCH FURTHER BACK AWAY FROM THE AXIS OF THE LOAD.
3.5 Pulling a load
CHECK THE POSITION OF THE WINCH, THE STATE OF THE LINE, THE STRENGTH OF THE ANCHORING POINT, KNOTS, HOOKS AND/OR  SHACKLES TO AVOID INJURIES AND MATERIAL DAMAGE.

3.5.1 Winding the line around the capstan drum
NEVER PLACE YOUR HANDS CLOSE TO THE LINE GUIDE, CAPSTAN DRUM AND ENTRY HOOK (PCW3000) OR GUIDE PULLEY (PCW5000 AND PCW5000-HS) WHEN THE  ENGINE IS RUNNING.
1. Start the engine and allow it to run idly for 30 seconds to warm up;
2. Thread the rope;
A. PCW3000: Thru entry hook then under the drum (Fig. 1).

B. PCW5000: Thru the hook, over the pulley and then under the drum (Fig. 2);

3. Wrap the line around the drum (3 or 4 turns);
4. Take the line behind the exit hook;
5. Keep your distance from the winch (approx. 1 m) and pull slowly and horizontally on the line until the line’s slack is taken up and you feel the tension in the line;
6. Inspect your installation to make sure that the anchoring of the winch and the entry hook is aligned with the line;
7. Check that the line is not rubbing against objects in its path;
8. Increase the engine speed and pull on the line to start moving the load.
3.5.2 Pulling
When pulling, position yourself so that you can see the winch and the load. Pull-on the line HORIZONTALLY. The tension you exert on the line keeps the winch level.
DO NOT WRAP THE LINE AROUND YOUR HANDS OR YOUR BODY! ALSO, BEWARE OF BUILT-UP TENSION CLOSE TO YOU AND MAKE SURE THAT YOU ARE A SAFE DISTANCE FROM THIS ACCUMULATION.

KEEP AN EYE ON THE CAPSTAN DRUM DURING OPERATION AND MAKE SURE THAT THE LINE DOES NOT CROSS THE LATTER. IF THIS  OCCURS, RELEASE THE TENSION IN THE LINE, STOP THE ENGINE AND REMOVE THE KINK.

3.5.2.1 If the line slips
If the line slips on the drum while you are pulling, add a turn of line around the drum (4th turn). The engine will stall when the winch reaches its maximum capacity. You should then review the
installation (add pulleys) or ”cradle” the load (see next section).
3.5.2.2 To ”cradle” the load
Pull until the engine nearly stalls and release the tension in the line. Then return the tension to the line and repeat as required.

BE CAREFUL WHEN USING THE LOAD ”CRADLING” METHOD. THIS METHOD MAY CAUSE RAPID WEAR TO THE LINE DUE TO THE HEAT CREATED ON THE DRUM.

IF THE WINCH PULLS THE LINE AND THE LOAD DOESN’T MOVE (OFTEN WHEN A VERY LONG LINE IS BEING USED), THE LINE STRETCHES  AND THE BREAKING POINT MAY BE REACHED CAUSING IT TO SUDDENLY COME BACK ON TO YOU. SLOWLY RELEASE THE TENSION IN THE LINE BUT BEWARE OF  THE BUILT-UP TENSION: THE LINE MAY QUICKLY GET AWAY FROM YOU CAUSING BURNS OR TAKING YOU TOWARDS THE WINCH.

3.5.2.3 Taking a break during pulling
SLOWLY release the tension in the line and allow it to slide over the drum.
NEVER ALLOW THE LINE TO SLIDE ON THE DRUM FOR MORE THAN A FEW SECONDS WHEN LOADED – THE HEAT GENERATED BY THE  FRICTION MAY MELT OR DAMAGE THE LINE.
3.5.2.4 To maintaining a load without releasing the tension
You must maintain the tension at the end of the line by holding it or attaching it to a fixed object.
1. Turn off the engine;
2. Complete two turns of line around the exit hook before removing the tension from your hands (Fig. 1 below);
3. Then do two half-knots around the exit hook (Fig. 2 below).

3.5.2.5 To recommence pulling
Release some of the tension before restarting the winch’s engine. Firstly, undo the two half-knots. Allow the line to move slowly to release the tension. Then, whilst holding the line in one hand, restart the engine while pulling on the starter and increase the engine speed. You can recommence pulling.
3.5.2.6 If it is essential to keep the tension in the line at startup
You can use a blocker or a Prusik knot connected to your anchoring point to maintain the tension in the line. You can also use a self-locking pulley PCA-1271 or PCA-1272. They are particularly useful for pulling rolling objects and for directional felling.

3.5.2.7 If your rope is too short
If your line is too short, connect two lines together:
1. Fig. 1-1: Use 2 bowline knots to link your two lines together.
2. Fig. 1-2: Allow approx. 1 m (3′) of line to exceed the knot of the line pulling the load. This length of the line will be used for pulling when the knot is undone.
3. Fig. 2: Stop the winch before the knots reach the winch; they will not be able to pass through and the line will become tangled.
4. Release the tension in the line. Attach the load to a fixed point if necessary.
5. Untie the line’s knot and use the remaining length to wind it around the drum and restart the winch again.

3.5.2.8 Stopping the winch

1. Gradually release the tension to gradually lower the winch towards the ground;
2.  Lower the throttle lever to the idle position;
3.  Set the on/off switch to the OFF position;
4. Do not touch the capstan drum after use. It may be hot and burn your skin.

4 Maintenance
4.1 Cleaning
When your work is complete, clean and dry the winch.

DURING CLEANING, CHECK THE WINCH, THE HOOKS, THE LINE, AND THE POLYESTER SLING FOR ANY DAMAGE OR SIGNS OF WEAR
Regularly remove the capstan drum and clean around the shaft. Any accumulated debris may damage the seal. Brush the shaft with a little oil to avoid corrosion.

4.2 Lubrification
The gearbox is lubricated in the factory and thus should not require lubrication or maintenance. If oil losses become apparent, check the oil level by placing the winch on a level surface and unscrew the cap. Use an 8 mm hexagonal key.

When tipping the winch forwards, a little oil may escape through the hole. If required, you can add SAE80W90EP gear oil. PCW5000 and PCW5000-HS only:

The entry guide pulley must turn freely. Lubricate it regularly using a light oil, otherwise, there is a risk of premature wear due to dirt between the axis and the pulley. If necessary, remove it to get rid of any dirt. Use an 8 mm hexagonal key.

4.3 Honda engine
Maintain the engine according to the instructions provided in the Honda engine user manual.
4.4 Storage
Always store your Portable Capstan WinchTM on its base. Please consult the Honda engine user manual for storage instructions.
4.5 Spark arrestors
PCW3000: Since your winch is equipped with integrated spark arrestors, you must clean them after one hundred (100) hours of operation. Consult the Honda engine manual for the cleaning procedure.
PCW5000 and PCW5000-HS: If your winch is equipped with an optional spark arrestor (PCA-1151, sold separately), you should clean this every one hundred (100) operating hours to ensure that it works properly. Consult the Honda engine manual for the cleaning procedure.

5 Additional information
5.1 Accessories
A full range of accessories is available. Take a look at www.portablewinch.com.
5.2 Warranty
The Portable Winch Co. winch and accessories are guaranteed against all manufacturing defects when owned by the ”original owner” as defined here below. The “original owner” is defined as the person or entity that purchased the winch or accessories from an authorized Portable Winch Co. dealer as shown by the original invoice. The warranty is transferable if the new buyer holds a copy of the original invoice. This warranty does not apply to items sold ”as is”. The warranty does not apply to the wear parts defined as those coming into contact with the line during pulling.
Portable capstan  winches are covered as follows :
● PCW3000
Commercial use: 1 year
Private use: 5 years
● PCW5000 et PCW5000-HS
Commercial use: 1 year
Private use: 5 years
Serviced by Portable Winch Co. or its retailers.
Engine :
The Honda engine is guaranteed by Honda Motor Corporation, and the warranty period may vary from one country to another.
All Honda service centers may make warranty repairs, if necessary. Please keep your proof of purchase (original invoice including the serial number of the winch). It will be used to establish the start date of the warranty period. Portable Winch Co. will replace or repair, at its discretion, any faulty products. All other Portable Winch Co. accessories are covered by a one-year (1) warranty with the exception of the lines which are covered by a 3-month warranty. If you have any questions, please consult the warranty policy at www.portablewinch.com Extend your warranty for free We want to thank you for your purchase. To do this, we are offering you AN ADDITIONAL ONE-YEAR (1) WARRANTY FOR FREE!
It’s simple, just register your winch at www.portablewinch.com or over the phone on 1 888 388-7855 or + 1 819 563-2193.
5.3 Troubleshooting area
In case of problems, consult the Troubleshooting section at www.portablewinch.com in the Manuals and instructions section.
5.4 Exploded-views
To access the exploded view of your winch, consult Exploded views at www.portablewinch.com on the Manuals and instructions page or see the end of the manual.
5.5 Technical data

MAXIMUM PULLING FORCE
(SINGLE LINE)| 700 kg
SPEED| 10 m/min
GEARBOX| HARDENED STEEL GEARS/OIL LUBRICATION
WEIGHT (DRY)| 9,5 kg
DIMENSIONS (OVERALL)| 35 cm x 28,9 cm x 26,1 cm
ROPE| DOUBLE BRAID POLYESTER WITH LOW
ELASTICITY (NOT INCLUDED)
LENGTH| UNLIMITED
MINIMUM DIAMETER| 10 mm
MAXIMUM DIAMETER| 12-13 mm
RECOMMENDED DIAMETER| 10 mm
Guaranteed sound power level
– LWA dB(A)| 108 dB(A)
Uncertainty factor KwA dB(A)| 2.5 dB(A)
Measured sound pressure level –
LpA dB(A)| 93 dB(A)
SPECIFICATIONS| PCW3000
---|---
ENGINE| HONDA GX-35 4-STROKE ENGINE
DRUM DIMENSIONS| Ø 76 MM, UP TO 4 TURNS OF 10 MM ROPE
MAXIMUM PULLING FORCE
(SINGLE LINE)| 700 kg
SPEED| 10 m/min
GEARBOX| HARDENED STEEL GEARS/OIL LUBRICATION
WEIGHT (DRY)| 9,5 kg
DIMENSIONS (OVERALL)| 35 cm x 28,9 cm x 26,1 cm
ROPE| DOUBLE BRAID POLYESTER WITH LOW
ELASTICITY (NOT INCLUDED)
LENGTH| UNLIMITED
MINIMUM DIAMETER| 10 mm
MAXIMUM DIAMETER| 12-13 mm
RECOMMENDED DIAMETER| 10 mm
Guaranteed sound power level – LWA dB(A)| 108 dB(A)
Uncertainty factor KwA dB(A)| 2.5 dB(A)
Measured sound pressure level – LpA dB(A)| 93 dB(A)

6.0 CE Declaration of conformity

DECLARATION OF CONFORMITY
PORTABLE WINCH CO.
1170, rue Thomas-Tremblay
Sherbrooke, QC J1G 5G5
CANADA
Tel: +1 819 563-2193
www.portablewinch.com

Declare, under our sole responsibility, that the product :
Portables Capstan Winches
Models PCW3000, PCW5000 and PCW5000-HS

Designed for this use:

Pulling non-rolling objects at angles of +45º on a horizontal surface.

In compliance with the ”Machines” directive 2006/42/EC as well as the following directives:

– 2004/30/UE Electromagnetic Compatibility Directive.
– 2000/14/CE Directive on Environmental Noise Emissions.

M. Gerold Vonblon,
Landstrasse 28, A-6714 Nuziders is authorized to compile the technical file.
Signed by:

Name: Pierre Roy
Position: Managing Director
In Sherbrooke, QC, Canada
Friday, 23rd November 2018.

PCW3000

PART
NUMBER| DESCRIPTION| QTY| PART
NUMBER| DESCRIPTION| QTY
---|---|---|---|---|---
10-0094| WINCH HANDLE| 1| 31-0019| HCS 3/8-24 X 1- Gr5 – ZN| 1
10-0095| GUARD PLATE PCW5000| 1| 31-0024| BHCS 1/4-20 X 1 – SS| 6
10-0096| CAPSTAN DRUM 57mm| 1| 31-0025| BHCS 1/4-20 X 3,4 – SS| 6
10-0098| BUSHING FOR SAFETY HOOK| 2| 32-0002| FLANGE BOLT SERRATED M6-1 x
12mm – ZN| 6
10-0099| ALUMINIUM ROPE EXIT HOOK| 1| 33-0005| NUT 1/2-13 NYLON – ZN| 1
10-0100| ROPE GUIDE FOR CAPSTAN
DRUM 57mm| 1| 35-0004| FLAT WASHER 1/2 – ZN| 4
10-0101| ROPE ENTRY PULLEY| 1| 39-0042| TAPPING SCREW-TYPE AB

10×5/8| 1

10-0102| RETAINING WASHER (1/4 X 1-1/4
OD) – ZN| 1| 43-0013| KEY FOR CAPSTAN DRUMS 57
MM, 85 MM & 108 MM (5/16 X
1-1/2)| 1
10-0103| ROPE KEEPER| 1| 44-0019| VINYL GRIP| 1
10-0119| SHOULDER BOLT 5/8 X 1 1/2 – ZN| | 45-0028| SUPPORT PLATE FOR ON/OFF
SWITCH| 1
10-0324| SWITCH MOUNT SPACER| 1| 45-0032| ON/OFF SWITCH| 1
31-0010| HCS 1/2-13 X 6 – GR5 – ZN| 1| PCA-1281| SAFETY HOOK WLL: 3/4 TON| 2

PART
NUMBER| DESCRIPTION| QTY| PART
NUMBER| DESCRIPTION| QTY
---|---|---|---|---|---
10-0098| BUSHING FOR SAFETY HOOK| 2| 32-0007| SHCS M8-1.25 X 16mm – BLACK| 2
10-0102| DRUM RETAINING WASHER (1/4
X 1-1/4 OD) – ZN| 1| 32-0008| HEX FLANGE SERRATED BOLT
M8-1.25 X 16mm – ZN| 2
10-0129| CAPSTAN DRUM 76mm| 1| 32-0009| SHCS M5-0.80 X 10mm| 1
10-0130| GUARD PLATE PCW3000| 1| 32-0051| SHCS M6-1 X 16mm – ZN| 2
10-0132| ENGINE ALUMINUM COUPLING
PC W3000| 1| 32-0055| BRCS M5-0.8 X 8mm – SS| 2
10-0133| ENGINE COUPLING PLATE| 1| 32-0056| HEX FLANGE SERRATED BOLT
M6-1.0 X 20mm – ZN| 4
10-0134| THROTTLE CABLE ASSEMBLY
PC W3000| 1| 33-0005| NUT 1/2-13 NYLON – ZN| 1
10-0135| ROPE EXIT HOOK PCW3000| 1| 33-0011| SQUARE NUT 10-24 – ZN| 1
10-0136| ROPE ENTRY HOOK PCW3000| 1| 35-0004| FLAT WASHER 1/2 – ZN| 4
10-0137| WINCH HANDLE PCW3000| 1| 39-0028| TAPPING SCREW – TYPE B-

10×1/2| 2

10-0415| GEARBOX 200:1| 1| 43-0057| KEY FOR CAPSTAN DRUMS 76
MM (8 MM X 30 MM)| 1
10-0427| ALUMINIUM ROPE GUIDE FOR
CAPSTAN DRUM 76mm| 1| 44-0002| THROTTLE LEVER PCW3000| 1
31-0010| HCS 1/2-13 X 6 – GR5 – ZN| 1| 45-0001| HONDA ENGINE GX-35 NT-S3| 1
31-0038| MACHINE SCREW PAN HEAD
SQUARE DRIVE 10-24 X 3/4-ZN| 1| 70-0031| ON/OFF SWITCH ASSY. FOR
PCW3000| 1
32-0005| BHCS M6-1 x 20mm – SS| 2| PCA-1281| SAFETY HOOK WLL: 3/4 TON| 2

www.portablewinch.com
info@portablewinch.com
1 888 388-7855 / +1 819 563-2193
Rev: 02 (2020-06-29)
44-0175
Written and published in Canada

References

• Portable Winch Co. | USA – Portable Winch USA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>