PEREL Pir Motion Detector Flush Mount User Guide
- June 7, 2024
- PEREL
Table of Contents
USER MANUAL
Introduction
To all residents of the European
Union Important environmental information about this product
This symbol on the device or the package indicates that disposal of the device
after its lifecycle could harm the environment. Do not dispose of the unit (or
batteries) as unsorted municipal waste; it should be taken to a specialized
company for recycling. This device should be returned to your distributor or
to a local recycling service. Respect the local environmental rules. If in
doubt, contact your local waste disposal authorities.
Thank you for choosing Perel!
Please read the manual thoroughly before bringing this device into service. If
the device was damaged in transit, do not install or use it and contact your
dealer.
Symbols
| 1 | CE marking. |
|---|---|
| 2 | Read and understand this manual and all |
safety signs before using this appliance.
3| Indoor use only.
4| Switch of micro-gap construction.
5| Incandescent lamp.
6| Energy-saving lamp.
Safety Instructions
● This device can be used by children aged from 8 years and above, and persons
with reduced physical, sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or instruction concerning
the use of the device in a safe way and understand the hazards involved.
Children shall not play with the device. Cleaning and user maintenance shall
not be made by children without supervision.
● Do not disassemble or open the housing.
● There are no user-serviceable parts inside the device. Refer to an
authorized dealer for service and/or spare parts.
● Do not immerse the device in any liquid. Keep away from high heat and fire.
General Guidelines
● Refer to the Velleman ® Service and Quality Warranty on
www.velleman.eu.
● Protect this device from shocks and abuse. Avoid brute force when operating
the device.
● Familiarise yourself with the functions of the device before actually using
it.
● All modifications of the device are forbidden for safety reasons. Damage
caused by user modifications to the device is not covered by the warranty.
● Only use the device for its intended purpose. Using the device in an
unauthorized way will void the warranty.
● Damage caused by disregard of certain guidelines in this manual is not
covered by the warranty and the dealer will not accept responsibility for any
ensuing defects or problems.
● Keep this manual for future reference.
Installation Guidelines
● Choose a proper installation location. Avoid places where temperature
changes frequently, e.g. near air conditioners or heating devices.
● Avoid pointing the appliance towards objects with highly reflective surfaces
such as mirrors.
● Avoid pointing the appliance near heat sources such as heating vents, air
conditioning units, etc.
● Avoid pointing the appliance towards objects that may move in the wind such
as curtains, plants, etc.
● Install the appliance at a distance of a minimum of 60 cm when using a lamp
of 60 W or more.
● Make sure the installation surface is immobile.
● Also, avoid obstructions or moving objects in the detection field of the
appliance to prevent unnecessary activation.
● The minimum installation height is 1.7 m, the maximum installation height is
3.5 m.
Connection
Warning! Risk of electroshock! Touching live wires can cause life-
threatening electroshocks. Has the device repaired by qualified personnel?
Disconnect the power source. Cover and shield any adjacent live components.
Ensure the device cannot be switched on. Make sure the power supply is
disconnected.
● Connect according to the wiring diagram.
● Switch on the power and proceed with the installation.
Installation
● Fold the metal springs upwards and insert them in the installation location.
● Release to lock the appliance.
Testing
● Test the detector at the point of time you feel the lamp needs to be
switched on.
● Turn the LUX knob fully clockwise; turn the TIME knob fully anti-clockwise.
● Switch on the power. The detector needs a warm-up time of ± 30 seconds
before it will switch on the connected lamp. When no signal is detected, the
lamp will switch off after ± 10 seconds.
● Turn the LUX knob fully anticlockwise. The lamp should switch off.
Setting
● Turn the LUX knob until the lamp switches on.
● Now, set the switch-off delay with the TIME knob going from ± 10 seconds to
± 7 minutes.
● Close the detector.
Care and Maintenance
The appliance does not need any particular maintenance. However, occasionally wipe it with a damp cloth to keep it looking new. Do not use harsh chemicals, cleaning solvents, or strong detergents.
Specifications
switch type …………………………………………………. relay
detection angle ……………………………………………. 360°
detection range ……………………………….. 6 m (< 24 °C)
rated load
tungsten ……………………… max. 1200 W – max. 5.5 A
fluorescent ……………………. max. 300 W – max. 1.5 A
LED …………………………… max. 1000 W – max. 4.5 A
IP rating …………………………………………………….. IP20
power supply ………………………… 220-240 V~, 50/60 Hz
working temperature …………………….. -10 °C to +40 °C
working humidity ………………………………….. < 93 % RH
time-delay switch ……………. 10 s ± 3 s to 7 min ± 2 min
light control ……………………………….. < 10 lx to 2000 lx
dimensions ……………………………. Ø 50 x Ø 40 x 66 mm
weight……………………………………………………….. 50 g
Use this device with original accessories only. Velleman NV cannot be held responsible in the event of damage or injury resulting from (incorrect) use of this device. For more info concerning this product and the latest version of this manual, please visit our website www.perel.eu. The information in this manual is subject to change without prior notice.
© COPYRIGHT NOTICE
The copyright to this manual is owned by Velleman NV. All worldwide rights
reserved. No part of this manual may be copied, reproduced, translated, or
reduced to any electronic medium or otherwise without the prior written
consent of the copyright holder.
Imported for Perel by Velleman nv
Legen Heirweg 33, 9890 Gavere, Belgium
www.perel.eu
References
- Details â Own brands â Velleman â Wholesaler and developer of electronics
- Velleman â Wholesaler and developer of electronics