EACHINE Hall Sensor Gimbals 2.4GHz 16CH Internal Multiprotocol RF System OpenTX Radio Transmitter RC Drone User Manual
- June 7, 2024
- Eachine
Table of Contents
Hall Sensor Gimbals 2.4GHz 16CH Internal Multiprotocol RF System OpenTX
Radio Transmitter RC Drone
Introduction
Thank you for purchasing the Eachine TX16S 2.4g remote control system. The
system is versatile and can be used by beginners and professionals. In order
to ensure the correct and safe use of this product, please read this
instruction manual carefully before use. Changes have been made due to a
version upgrade. The information contained in this manual is subject to change
without notice.
TX16S remote control is suitable for all types of fixed-wing, glider,
helicopter, boats, robotics, multi-rotor aircraft and more. The model type can
be selected according to the aircraft used, and various hybrid functions can
be used.
Sincerely, The Eachine Team.
Safety instructions.
Many remote control models are equipped with powerful motors and sharp propellers. Use caution when operating models. When assembling or maintaining, make sure the model is powered off and the propeller is removed.
Do not operate the TX16S remote control system under the following conditions:
- In severe weather or strong wind conditions, such as rain, hail, snow, storm or electromagnetic environment.
- Under any circumstances where visibility is limited.
- In areas where people, property, high-voltage power lines, public roads, vehicles or animals may be present.
- If you feel tired or unwell, or under the influence of drugs or alcohol.
- If the remote control or model appears to be damaged or not working properly.
- In areas where 2.4GHz interference is high or where 2.4GHz radios are prohibited.
- When the battery voltage is too low to use.
- In areas where local regulations prohibit the use of aviation models.
Manuals and firmware downloads.
TX16S comes pre-installed with standard OpenTX firmware. To download the latest
software manual, visit the Eachine website: https://www.eachine.com/
Important！
The TX16S is shipped with the most stable firmware at the time of manufacture.
Please only update firmware if you are experienced and confident in updating
system firmware. Incorrect updates may render the radio inoperable.
Remote control overview
Model selection and protocol selection
TX16S comes with a 4-in-1 multi-protocol high-frequency module, which is
compatible with many different protocols. To view the latest list of all
compatible protocols, please visit:
https://github.com/pascallanger/DIY-Multiprotocol-TX-
Module/blob/master/Protocols_Details.md.
Please note that new protocols are constantly updated and added to the latest
firmware, and some new protocols may require firmware upgrades.
press the MDL button to enter the MODEL settings, select MULTI in the MODEL SETUP page, and select the protocol you want to use in the sub-options. According to the RF protocol you choose, the system will automatically open the corresponding RF chip aboard the internal RF module while shutting down the other three RF chips that are not in use. Only one RF chip on the module will be switched on at a time to ensure that there is no interference from the unused RF chip.
- The Bind button is used to start the linking process.
- The Range button reduces power to 1/30 to facilitate testing of remote control distances.
Note:
OpenTX software is very powerful and has a large number of programming and
mixing functions. Please download the comprehensive software installation
guide for more detailed instructions from the following link: https://www
.open-tx.org
Specifications
Size: 286.9128.9183.8mm
Weight: 750g (without battery)
Transmission frequency: 2.400GHz-2.480GHz
Transmitter module: Internal 4-in-1 multi-protocol module (CC2500 CYRF6936
A7105 NRF2401) Transmitting power: Max 22dbm (transmitting power is
adjustable)
Antenna gain: 2db (transmit power adjustable)
Working current: 400mA
Working voltage: 6.6-8.4v DC
Remote control distance:> 2km @ 22dbm
Open source firmware: OpenTX （remote control）DIY-Multiprotocol-TX-
Module（Internal RF Firmware driven by Open TX）
Channels: Up to 16 channels (depending on the receiver)
Display: 4.3-inch TFT full-color display with a resolution of 480 * 272
Gimbal: Non-contact 3D vector Hall with Aluminum facia. JR / FrSKY compatible
module bracket
Upgrade method: Support USB-C online / SD card offline upgrade
Protocols: Full series DSM2 / X full series Flysky and Flysky 2A FrSKY
(For a complete list of below link)
https://github.com/pascallanger/DIY-Multiprotocol-TX-
Module/blob/master/Protocols_Details.md
Support.
Warranty and Repairs.
Please retain your proof of purchase and contact the retailer you purchased
your TX16S from should you experience any problems with your radios hardware.
Firmware updates and OpenTX information.
For latest news and firmware updates from the OpenTX please visit https://www
.open-tx.org
User manual
For detailed user manual of TX16S OpenTX system firmware, please visit
https://www.open-tx.org.
Important note on Power and charging precautions.
The TX16S has built-in USB charging function for 2cell 7.4v Battery packs (2 x
3.7v Lithium cell packs). The charging circuit is only suitable for 2x 3.7v
lithium-ion 18650, 2 x 21700 3.7v lithiumion (21700 2s 7.4v Lithium-Ion pack)
or 2x 3.7v Lipoly batteries (2s 7.4v Lipo battery pack). The nominal battery
voltage per cell is 3.7v and the maximum charging cut off voltage is 4.2v per
cell.
Approved for use
2x 3.7v Li-ION 18650 cells (7.4v using supplied tray)
2 x 3.7v Li-ION 21700 cells (Assembled as 7.4v 2s Battery pack)
2 x 3.7v Lithium-polymere cells (Assembled as 7.4v 2s Battery pack)
DO NOT use
3.6v Li-ION cells
2S 6.6v LiFE Battery packs
LiFEP04 cells
Do not use 2s 6.6v LiFE battery pack, 18650 lithium-ion cells with a nominal
voltage of 3.6v or LiFEP04 18650 Round cells. Using the built in USB charger
with incorrect battery types and voltage may cause damage to the remote
control or fire.
Check the health and condition of the batteries regularly. Do not use damaged
cells. Never charge your device unattended. Always charge in a safe area away
from flammable materials. If the remote control gets wet or damaged in any way,
do not charge it.
Eachine is not responsible for any adverse consequences caused by using or
misusing this device.
EU Simple Declaration of Conformity
RadioMaster declares the radio equipment TX16s is in compliance with EU
directives Directive 2014/53/EU. Full text of the declaration of conformity is
available at the following website https://www.eachine.com/
Manufacturer by
ShenZhen RadioMaster Co., Ltd
5th Floor, Yutian Building, No. 18 Yangtian Road, Xin’an Street, Baoan
District, Shenzhen, Guangdong.
FCC ID: 2AV3G-TX16S
FCC Information
This equipment has been tested and found to comply with the limits for Part 15
of the FCC
rules. This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions : (1) This device
may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired
operation.
Full text of the declaration of conformity is available at the following
website https://www.ea-chine.com/
CAUTION:
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. This
product contains a radio transmitter with wireless technology which has been
tested and found to be compliant with the applicable regulations governing a
radio transmitter in the 2.400GHz to 2.4835GHz frequency range.
Antenna Separation Distance
When operating your Eachine transmitter, please be sure to maintain a
separation distance of
at least 20 cm between your body (excluding fingers, hands, wrists, ankles and
feet) and the antenna to meet RF exposure safety requirements as determined by
FCC regulations.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>