Meauro Mini Projector User Manual
- June 7, 2024
- Meauro
Table of Contents
Meauro Mini Projector
Safety Instructions
- For the best effects, please use the projector in a darker room or with the curtains closed.
- Please use the projector with caution, as dropping or collision may damage the components or cause blurred images and abnormal display.
Please carefully read this user manual before using the projector and keep it properly for future reference.
- To ensure a steady power supply for the projector, please use the power supply circuit that meets your national electricity standard. Please use a grounded power outlet.
- Use the type of power source indicated on the projector for power supply.
- Do not directly look into the lens of the projector while the projector is operating, as intense light may hurt your eyes.
- Do not place the projector on objects (such as cloths, blankets, etc.) that may cause blockage on the air vents.
- The product is not waterproof and should be prevented from water drenching or splashing. It’s recommended not to put items with liquid (such as vases, water glasses, etc.) near the projector.
- Never let the projector get wet or let water get inside of the projector to prevent an electric shock.
- Unplug the power cord if the product is not going to be used for a long time.
- Use the original foam when transporting the product
- Do not attempt to repair the projector by yourself if it is found to be faulty, and please contact our customer service.
- The device is only applicable for safe use in an environment with the altitude less than 2000m. When used in an environment with the altitude above 2000m, there may be a safety hazard.
What’s in the Box
1 x Projector
1 x 19VDC Adapter
1 x Remote Controller (2xAAA batteries not included)
1 x User Manual
Product Introduction
Front View
Back View
Top View
Bottom View
Infrared Remote Controller Features
Operation Descriptions
Installing the Projector
When installing the projector, you can either place it on a solid and stable
desktop or hang it to the ceiling via a mounting bracket. Ensure good
ventilation around the projector and that no objects cover or block the air
vents. There shouldn’t be
surface should be white and even.
By reference to the data in the following table and based on the preset projection sizes, you can put the projector in a place that maintains the best distance to the projection screen. To achieve 40-200inch projection image, the minimum distance and maximum distance of the projector to the projection surface should be 1.2m and 7m respectively.
Projection size (inch)| Screen length (cm)| Screen width (cm)|
Distance between lens and screen (cm)
---|---|---|---
40| 89| 50| 119
50| 111| 62| 148
60| 133| 75| 178
70| 155| 87| 208
80| 177| 100| 237
90| 199| 112| 267
100| 221| 125| 297
110| 244| 137| 326
120| 266| 149| 356
Note: The above data are for reference only, and please take actual
measurement as standard.
The device is built in with an automatic vertical keystone correction
function, which is used for correcting the projection image.
Installation Method
Based on your using environment and need, you can either hang this projector
to the ceiling via a special mounting bracket, or place it on a stable desktop
for front projection to the screen. Of course, you can also use other methods
to install the project: 
Notes:
- When using a mounting bracket for installation, the projector shouldn’t be the keystone correction function.
- Be sure to install the projector at the symmetry axis of the left and right of the screen, so as to avoid keystone distortion on the left and right of the image. Ensure good ventilation around the projector after installation. There shouldn’t be any object that covers or blocks the air vents of the projector.
- Do not connect the projector to a power source during installation, otherwise it may cause an electric shock or projector circuit fault.
Power ON/OFF
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>