New England Madison Sturbridge Trinity Burton Lamp Post Instruction Manual
- June 7, 2024
- New England
Table of Contents
Madison Sturbridge Trinity Burton Lamp Post
New England Arbors
Leadership by Design
ASSEMBLY INSTRUCTIONS
The Madison/Sturbridge/Trinity/Burton Lamp Post
Madison/Trinity Lamp Post
Sturbridge/Burton Lamp Post
Please read through before starting assembly.
Check Boxes for These Contents (1 Box)
In the event of missing or defective parts please call our customer service dept. at 1 800 282 9346, ext #20 (Mon. to Fri. 8:00 AM to 4:00 PM EST). (UK Tel: (44) 2038 687160 – Mon. to Fri. 1:00 PM to 10:00 PM GMT)
- Lamp PostTop (1) – 5″ x 5″x 58″ (12.7 x 12.7 x 147.3 cm) – 10890 White , 14053 Brown
- Post Coupler (1) – 10906 White, 14053 Brown
- Lamp Post Bottom (1) – 5″ x 5″x 14″ (12.7 x 12.7 x 35.5 cm) – 10889 White, 14052 Brown
- Post Cap (1) – 10789 White, 14051 Brown
- Base MoldingTrim Cap (1) – 10764 White, 14055 Brown
- Base Molding Post (1) – 10174-1 White, 14058 Brown
- Base Molding Bottom Insert (1) – 10765 White, 14057 Brown
- 1-1/2″Self-TappingScrews (4) – 20005 White, 20031 Brown
- Vinyl Weld Glue (1) – 20000 White, 20038 Brown
- PostTrim (1) – Included with the Sturbridge/Burton Lamp Post Only – 10698-1 White, 14029 Brown 10
Tools You Will Need
- Wheelbarrow or bucket (to mix concrete)
- Tape Measure
- Level
- Shovel
Purchased Separately
- Lamp.
- 4×4 Pressure treated lumber. – 8′ (2.4 m) long
- Two bags of pre-mix concrete. *
- Strongly recommended for the stability of this product.
General Information
- Read Instructions through carefully before beginning assembly.
- When handling components, place on a non-abrasive surface (i.e. shipping box) to avoid scratching.
- We recommend an area approx 10’x 8′ (3m x 2.4m) for unobstructed handling.
Important Note:
- Please refer to local codes before installing outdoor lighting. UF-rated cable should be used for underground wiring and all materials should be approved by the Underwriter’s Laborator (UL). New England Arbors assumes no liability for errors, ommissions or the outcome of any project.
STEP ONE
Base Molding Assembly
Apply a generous amount of vinyl glue to the underside of the base molding and
the top side of the base molding bottom insert and attach to the
base molding post as shown aside.
STEP TWO
Lamp Post Assembly
A. Apply a generous amount of vinyl glue to the ribbed surface of the
post coupler as shown and join the two posts as illustrated. 2 Slide the base
molding over the lamp post. If you purchased the Madison/ Trinity Lamp Post,
proceed to step three. If assembling the Sturbridge/ Burton Lamp post continue
to step B.
B. Slide the post collar down measuring 12 inches from the top of the
post. Once desired height is achived, make a note of the position of the
collar.
C. Slide the collar UP and out of the way, then apply a generous amount
of vinyl glue at the top of where the collar would sit.
D. Slide the collar back down to its desired height and allow some time
for the vinyl glue to set and cure.
STEP THREE
Apply a generous amount of vinyl glue to the inside base of the post cap and place over the top end of the lamp post as illustrated.
STEP FOUR
Wood Post Installation
Dig 36 in. (91.5 cm) deep hole in the desired location. Verify the depth of
the hole to ensure that the 4×4 wood post will be buried 36 in. (91.5 cm) into
the ground. Fill the hole 3/4 full with pre-mix concrete (not included).
Insert the post into the concrete and check for level. Allow time for the
concrete to set, then fill in the remainder of the hole.
STEP FIVE
Lamp Post Installation
A. If necessary, pre-wire the lamp by running the wire inside the cavity
of the post through the universal 3 in. (7.62 cm)collar. If installing a solar
lamp, disregard this step.
B. Slide the lamp post assembly over the wood post.
C. Line up the one corner of the vinyl post up against the wood post and
fasten the two touching sidCes with the provided screws.
STEP SIX
Installing Lamp
Follow the instructions included with the lamp (purchased separately) and
secure it to the round collar on top of the post. You may need to modify how
it attaches to the collar. Ensure the lamp post wiring is inside this cavity.
www.newenglandarbors.com www.newenglandarbors.co.uk
North America Toll Free Phone: 1 800 282 9346 United Kingdom Tel: (44) 2038 687160