speco technology Flexible Intensifier Bullet IP Camera Installation Guide

: June 7, 2024
: speco technology

Table of Contents

Notice
INFORMATION
PRECAUTIONS
LIMITATION OF LIABILITY
DISCLAIMER OF WARRANTY
PRODUCT OVERVIEW
- Key Features
- Specification
NAME AND FUNCTION OF EACH PART
- Package Contents
- Name and Function
INSTALLATION
DIMENSIONS (mm)
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

speco technology Flexible Intensifier Bullet IP Camera

Notice

Thank you for purchasing this product. This guide is designed to be a reference tool for the product. Please read it carefully before operating the product and retain it for future reference. Should you require any technical assistance, please contact Speco Technologies Technical Support.

|

CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.

---|---
| The lighting flash with an arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of non-insulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
---|---
| The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

INFORMATION

This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at its own expense.

WARNING

Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

CAUTION – To prevent electric shock and risk of the fire hazards

Do NOT use power source other than that specified.
Do NOT expose this appliance to rain or moisture.

This installation should be made by a qualified service person and should conform to all local codes.

PRECAUTIONS

Please read the manual carefully before the installation in order to set up the camera correctly and to obtain the best picture quality.
Installation and services should only be carried out by an authorized personnel according to local safety regulations.
If any liquid or solid matter gets into the housing, immediately disconnect the camera from power supply and have it checked by your authorized dealer before reusing.
Avoid installing the camera in extremely hot or cold places.
If you are not a certified person, never try to dismantle the camera.
To avoid electric shock, never remove the screws or covers. There are no parts inside that need maintenance by the user. All maintenance should be carried out by qualified personnel.
Avoid installing the camera in a place of high humidity.
Avoid installing the camera at a place exposed to gas or oil.
Don’t point the camera directly at sunlight.
Please pay special attention to keep the unit from dropping or external shock during the process of transportation or handling.
Never try to touch the camera with wet hands. It may cause an electric shock.
Do not expose the camera to radioactivity. It can cause a serious damage on the image sensor

LIMITATION OF LIABILITY

This publication is provided “AS IS” without warranty of any kind, either express or implied, including but not limited to, the implied warranties of merchantability, fitness for any particular purpose, or non-infringement of the third party’s right.
This publication could include technical inaccuracies or typographical errors. Changes are added to the information herein, at any time, for the improvements of this publication and / or the corresponding product(s).

DISCLAIMER OF WARRANTY

In no event shall seller be liable to any party or any person, except for replacement or reasonable maintenance of the product, for the cases, including but not limited to below :

(Any damage and loss, including without limitation, direct or indirect, special, consequential or exemplary, arising out of or relating to the product.
Personal injury or any damage caused by inappropriate use or negligent operation of the user.
Unauthorized disassembly, repair or modification of the product by the user.
Inconvenience or any loss when images are not displayed, due to any reason or cause including any failure or problem of the product.
Any problem, consequential inconvenience, or loss or damage, when combined with third party devices.
Any claim or action for damages, brought by any person or organization, due to a violation of privacy when the surveillance footage, for some reason, becomes public or is used for the purpose other than surveillance.

PRODUCT OVERVIEW

Key Features

8.5 Mega pixel 1/2.5″ progressive scan CMOS image sensor for excellent image quality
Vandal resistant
IP67 compliant
3-Axis mechanism
Triple stream for simultaneous operations
Supports up to 4K ultra-HD image resolution (3840 x 2160)
Integrated motion detection with pre- and post-alarm image / video buffering
Tampering-Alarm function
Controllable frame rate
Full Duplex Two-Way Audio Support
Privacy Masking
HTTPS supported (Hyper Text Transfer Protocol Secured)
Integrated E-Mail, FTP, DDNS and DHCP client

Specification

CLASSIFICATION	Dome IP Camera
General	CPU

Temperature

| 14F ~ 122F
Storage Temperature| -4F ~ 140F

NAME AND FUNCTION OF EACH PART

Package Contents

APPEARANCE

| ****

DESCRIPTION

---|---
| IP Camera x 1
| Installation Guide x 1
| Drilling Template x 1
| L-Wrench x 1
| Tapping Screws (Ø4 x 30) x 3
| Plastic Anchor x 3
| CD x 1
**Junction Box
**| Tapping Screws (Ø4 x 30) x 4

| Plastic Anchor x 4
| Silicone Template x 1
| Junction Box x 1
| Screw PH (M4 x 12) x 3
****| L-Wrench x 1

Name and Function

NO.

| ITEM|

DESCRIPTION

---|---|---
| Power Connector| DC12V
| Network and POE Connector| POE (Power Over Ethernet) and LAN cable
| Sensor In / Alarm Out| Sensor In / Alarm out
| Audio-In| Audio in (Red)
| Audio-Out| Audio Out (White)
| IR LED| Infrared LED
| Lens| 3.6 ~ 11mm Motorized Lens
| luminance sensor| Control IR LED by sensing light
| BNC| Analog Video Output

INSTALLATION

Installation overview

Ceiling

Paste a Drilling Template on the ceiling or wall and drill screw points which will be dome for installation.
Fix the Surface Mounting Base by using Tapping Screws provided.
Fix the Flush mount Base on Surface Mounting Base.
Turn the camera Ass’y to the desired direction.
Turn the dome and shied cover to the camera direction.
Fix the Dome Cover Ass’y to the Flush mount Base by using Torx Screw and Torx L-Wrench.

Ceiling_Junction Box

3-Axis Adjustment

Tool-free 3-Axis mounting mechanism Perfect Tri-axis!

Panning axis up to 326° degree.
Tilting axis up to 65° degree.
Rotation axis up to 180° degree.

INSTALLATION EXAMPLE

Installation Example

Connecting to the Network

Open up IP Scanner.
IP Scanner can search for the device on the local network.
Please note that only devices that are on the same subnet can be discovered.
The device is set to DHCP mode by default.
In the device list, you can view the IP address, model number, and MAC address of each device. Select the applicable device and double click to open up the web viewer.

Accessing the Camera’s Web Setup Page

Open the browser and enter the camera’s IP address in the address bar or double click the device in IP Scanner
Enter the user name and password when prompted.
Default user name is admin and password is 1234.
If prompted for installation of the Active-X plug-in, allow the installation. Active-X is needed to view video from Internet Explorer.