Miele Dishwashers Instruction Manual

Dishwashers

Quick Start Guide

for dishwashers

These short instructions are not a substitute for the operating instructions supplied with the machine. It is essential to familiarise yourself with the dishwasher before using it for the first time. Take note of the Warning and Safety instructions, as well as the full descriptions on how to use your appliance.

en-AU, NZ
M.-Nr. 11 480 720 / 01

Guide to the appliance
Control panel

a On/Off sensor

f Express sensor

For switching the dishwasher on and For reducing the programme

off.

duration.

b In-operation indicator light

g AutoDos sensor

For indicating an ongoing wash

For activating/deactivating AutoDos.

programme when the door is closed. h Timer sensor

c Remote control sensor

For selecting a later programme start.

For activating/deactivating the Remote control option.

i Display For further information, see “Guide to

d Programme selection

the appliance – Display functions” in

ECO 50 °C = ECO 50 °C

the operating instructions.

Auto 45 °C 65 °C

= Auto 45­65 °C = Gentle 45 °C

j Back sensor For navigating back to the previous menu or deleting values which have

= QuickPowerWash 65 °C been set previously.

75 °C

= Intensive 75 °C = Further programmes/ Settings

k sensors For programme selection. For changing the values displayed.

e IntenseZone sensor

For scrolling to other menu pages.

Increases cleaning performance in the lower basket.

l OK sensor For selecting menu options and

values displayed.

For confirming messages.

Brief instructions
a AutoDos (automatic dispensing) b Detergent compartment c Rinse aid reservoir d Salt reservoir e Filter combination

Filling the salt reservoir Remove the lower basket from the
wash cabinet and unscrew the salt reservoir cap.
Damage to the water softener
from detergents. Dishwasher detergent will damage the water softener. Do not fill the salt reservoir with powder or liquid detergent.
Risk of corrosion due to saline
solution. Water or saline solution will run out of the reservoir when the cap is opened. Saline solution that runs out can cause corrosion in the wash cabinet and to the dishwasher load. The salt reservoir should therefore only be opened to replenish the salt.
Fill the salt reservoir with approx. 2 l of water (first use only).
Place the funnel provided over the salt reservoir and carefully fill with dishwasher salt until the reservoir is full.
Clean any excess salt from around the reservoir opening and then screw the salt reservoir cap on again firmly.
Immediately after filling the salt container, run the QuickPowerWash 65 °C programme with the Express option and without any load in the dishwasher to dissolve and remove any traces of salt from the cabinet.

Adding rinse aid Lift the yellow catch on the lid of the
rinse aid container . Only fill with rinse aid until the fill level
indicator (see arrow) turns dark when the door is open horizontally. Close the lid making sure it clicks into place. Wipe up any spilled rinse aid. This prevents over-foaming occurring during the next programme.
Loading the dishwasher
Detergent dispensing There are two ways of dispensing the detergent. During automatic dispensing, the AutoDos function will automatically dispense the required amount of detergent for each programme once a PowerDisk has been inserted. If you have deactivated automatic dispensing, you can dispense detergent manually.
Automatic detergent dispensing Before you can use AutoDos, you must insert a PowerDisk containing powder detergent into the PowerDisk compartment.

Slide the yellow catch of the AutoDos lid to and open it.
Before you use AutoDos for the first time, remove the transport lock from the PowerDisk compartment.
If the arrows in the PowerDisk holder and in the viewing window are not pointing towards each other, remove the PowerDisk holder.

Put the holder back into place so that the arrows point towards each other and the holder lies flat. When doing this, only hold the PowerDisk holder by the yellow tab in the middle. Do not hold it by the side tab.
Insert the new PowerDisk and press it evenly downwards until it sits flush.
Close the AutoDos lid and slide the yellow catch until it is aligned with the symbol.
The AutoDos function will be activated automatically. This setting applies to all programmes and you can change it at any time using the AutoDos sensor. If the PowerDisk is not in the correct starting position, it will be rotated automatically. Wait until this process is finished before you start a programme.

Manual detergent dispensing Dispense detergent manually if you have deactivated automatic dispensing. Follow the detergent dosage
recommended by the manufacturer on the packaging. Unless directed otherwise, use one detergent tab or add 20 to 30 ml of detergent to the detergent compartment, depending on the degree of soiling of the crockery. Lift the yellow catch on the lid of the detergent compartment . The lid will open. Fill the detergent compartment with detergent and push the lid shut until you hear it click into place.

Switching on Turn on the tap if it is turned off. Open the door. Touch the sensor.
Selecting a programme Touch the sensor for the required
programme. Further programmes can be selected under .
Selecting programme options (if required) You can select and deselect programme options via the relevant sensors and the display. The selected programme option will remain active for that particular programme until the setting is changed. Touch the sensor for the programme
option you want. The relevant sensor will light up brightly.
Activating the timer (if required) Touch the sensor. Select the function you want using
the sensors and confirm with OK. Enter the required time for the timer using the sensors and confirm with OK.
Starting a programme Start the programme by closing the
door.

Programme end – Switching off At the end of a programme, the optical in- operation indicator light will flash slowly with the door shut. The signal tones might also sound. The programme has finished when Finished appears in the display and the door has opened slightly (if applicable).
The drying fan may continue to run for a few minutes at the end of the programme.
Open the door. The dishwasher can be switched off
at any time using the sensor. Confirm the query Switch appliance off
with OK.
Risk of damage due to steam.
Steam from the dishwasher could damage the edges of delicate worktops when you open the door at the end of the programme if the fan is no longer running. If you have deactivated the automatic door opening function but would still like to open the door at the end of the programme, make sure that you open the door fully.
Unloading the dishwasher Dishes tend to break and chip more easily when they are hot. Allow the dishes to cool until they are comfortable enough to handle before unloading them.

Cleaning and care

Cleaning the spray arms
Particles of food can get stuck in the spray arm jets and bearings. The spray arms should therefore be inspected regularly (approx. every 2­4 months).

Do not run a wash programme
without the lower spray arm or without the filters fitted.

Switch the dishwasher off. Take out the cutlery tray (if your
dishwasher is fitted with one). Push the upper spray arm upwards to
engage the inner ratchet. Then unscrew the spray arm by rotating the screw thread anti-clockwise (overhead perspective).
Rotate the screw thread of the middle spray arm clockwise (see diagram) and remove the spray arm .
Remove the lower basket.

Rotate the screw thread of the lower spray arm anti-clockwise and pull the spray arm upwards to remove .
Use a pointed object to push food particles stuck in the jets into the spray arm.
Rinse the spray arm thoroughly under running water.
Refit the upper and middle spray arms.
Refit the lower spray arm and ensure that the filter combination lies flat in the base of the wash cabinet.
Rotate the screw thread of the lower spray arm clockwise until the arrow in the viewing window points to the lock symbol .
Make sure the spray arms can rotate freely.

Checking the filters in the wash cabinet
Do not run a wash programme
without the filters or without the lower spray arm fitted.
The message Check filters will appear in the display after every 50 programme sequences. Monitor the condition of the filter
combination regularly and clean it if necessary. Confirm the message with OK.
Cleaning the filters
Switch the dishwasher off. Remove the lower spray arm. Before removing the filter
combination, remove any coarse soiling to prevent it from entering the circulation system.

In order to clean the inside of the filter, pull the microfilter downwards and away from the filter combination.
Rinse all the parts under running water.
Push the microfilter back onto the filter combination.
Refit the filter combination so that it lies flat in the base of the wash cabinet.
Refit the lower spray arm to the filter combination using the screw thread.
Rotate the screw thread clockwise until the arrow in the viewing window points to the lock symbol .

Remove the filter combination.

Programme chart

Crockery
Temperature-sensitive dishes, glasses and plastics

Food deposits
Lightly dried-on food deposits

Programme features
Programme with glass care

All fresh to dried-on food deposits

Variable, sensor-controlled programme

Mixed crockery

Lightly dried-on food deposits

Short programme taking less than an hour

Standard dried-on normal food deposits

Pots, pans, everyday porcelain and cutlery

Stubborn dried-on, burnt-on food deposits containing starch or protein1

Water and energy saving programme
Maximum cleaning performance

No crockery

Residual salt after refilling the salt container

1 Food such as potatoes, pasta, rice or stews can leave starchy deposits. Deposits containing protein can be left by food such as fried meat or fish.

Flushes out salt residues

Programme2 Gentle 45 °C Auto 45­65 °C
QuickPowerWash 65 °C ECO 50 °C
Intensive 75 °C

Consumption estimate3
Energy consumption Water consumption Programme duration
Energy consumption Water consumption Programme duration
Energy consumption Water consumption Programme duration
Energy consumption Water consumption Programme duration
Energy consumption Water consumption Programme duration

QuickPowerWash 65 °C + Express

Programme duration 13 minutes, no heating up,
solely for flushing out salt.

2 All programmes can be combined with the “Express” or “IntenseZone” programme options.
3 The estimated values may change due to the selected settings or programme options, or the conditions in which the appliance is being used.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>