anko Wireless Headphones User Manual
- June 7, 2024
- Anko
Table of Contents
anko Wireless Headphones
FRONT
Included:
1 x Transmitter
1 x Receiver (headphones)
1 x 3.5mm to RCA adaptor cable 2 x 3.5mm audio cable
WARNING:
- Do not dispose of unit in fire or water.
- Never attempt to disassemble and reassemble. Waste electrical products should not be disposed of with household waste, please recycle where facilities exist. Check with your local authority for recycle advice.
- Keep your device and all accessories out of the reach of children and animals. Small parts moy cause choking or serious injury if swallowed.
- Avoid exposing your device to very cold or very hot temperatures (below o·c or above 45•c).
- Extreme temperatures can cause deforming of the device and reduce the charging capacity and life of your device.
- Do not allow your device to get wet-liquids can cause serious damage. Do not handle your device with wet hands.
Installation
Installing the Receiver (Headphones)
Insert 2 x AAA batteries (not included) into the battery compartment according
to the correct polarity.
Installing the Transmitter
- Insert 2 x AAA batteries (not included) into the battery compartment according to the correct polarity.
- Insert one end of the audio cable into the AUDIO socket on the back of the transmitter.
- Insert other end of the audio cable into the AUDIO-OUT socket of your chosen audio source. In cases where the AUDIO-OUT socket of the audio source is not the headphone 3.5mm socket, use the supplied RCA adaptor cable for connection (see installation diagram to the right).
- To achieve the best reception, spread out the transmitter audio cable which can also be used as an antenna.
Using your Headphones with a TV:
- Insert the transmitter audio cable into the AUDIO-OUT socket of the source. If a TV is used as the source, the TV can be muted to only output sound through the headphones.
- Move the FUNCTION SWITCH to the WIRELESS HEADPHONE position to turn on the Power LED of the transmitter.
- Long press the power button for 3 seconds to turn the headphones on, the power LED will illuminate.
- The headset will automatically connect with the transmitter.
Using your Headphones with an Amplifier
- Insert the transmitter audio cable into the AUDIO-OUT socket of the amplifier. Ensure the amplifier is switched ON and is generating an audio signal.
- Move the FUNCTION SWITCH to the WIRELESS EARPHONE position to turn on the Power LED of the transmitter.
- Long press the power button for 3 seconds to turn the headphones on, the power LED will illuminate.
- The headset will automatically connect with the transmitter.
Using your Headphones for Wireless Internet Chat / Gaming
- With the other audio cable, insert one end into the MIC socket of the transmitter and insert the other end into the MICROPHONE INPUT of the computer.
- Aim the microphone socket (MIC) of the transmitter towards you then move the FUNCTION SWITCH to the WIRELESS HEADPHONE position. The Power LED of transmitter will turn on.
- Long press the power button for 3 seconds to turn the headphones on, the power LED will illuminate.
- The headset will automatically connect with the transmitter.
Using your headphones with a cable (not wireless)
- Insert one end of the audio cable into the audio socket at the bottom of the headphones.
- Insert the other end of the cable into the headphone socket of your audio source.
- Your headphones are ready for use.
Saving battery power – switching off your unit
Save battery power by turning off your unit when not in use:
- Move the FUNCTION SWITCH on the transmitter to the OFF position.
- Long press the power button for 3 seconds to turn OFF the receiver (headphones).
- The Power LEDs on the transmitter and headphones will turn off. Remove batteries when not in use for long periods.
Channel switch function
Both headphone and transmitter have 7 channels. When they are on the same
channel, they can connect to each other.
- The Power LEDs on the headphone and transmitter have 7 colours. Different colour of light indicates different channels.
- Transmitter Channel Switch: Move the FUNCTION SWITCH on the transmitter to the WIRELESS HEADPHONE or MONITOR position. Short press the CH button on the transmitter to switch channel.
- Headphone Channel Switch: Long press the power button to turn on the headphone receiver. short press the power button and volume up button or volume down button at the same time to switch channel.
Monitor Function
Move the FUNCTION SWITCH on the transmitter to the MONITOR position after the
headphones and transmitter are paired. User can hear sound and voice in the
headphones collected by transmitter.
Installing the Transmitter
12 Month Warranty
Thank you for your purchase from Kmart.
Kmart Australia Ltd warrants your new product to be free from defects in
materials and workmanship for the period stated above, from the date of
purchase, provided that the product is used in accordance with accompanying
recommendations or instructions where provided. This warranty is in addition
to your rights under the Australian Consumer Law.
Kmart will provide you with your choice of a refund, repair or exchange (where
possible) for this product if it becomes defective within the warranty period.
Kmart will bear the reasonable expense of claiming the warranty. This warranty
will no longer apply where the defect is a result of alteration, accident,
misuse, abuse or neglect.
Please retain your receipt as proof of purchase and contact our Customer Service Centre on 1800 124 125 (Australia) or 0800 945 995 (New Zealand) or alternatively, via Customer Help at Kmart.com.au for any difficulties with your product. Warranty claims and claims for expense incurred in returning this product can be addressed to our Customer Service Centre at 690 Springvale Rd, Mulgrave Vic 3170.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. For New Zealand customers, this warranty is in addition to statutory rights observed under New Zealand legislation.
Product Details
- Fils name: 5060_MAN_OH_42568544_N_Wirelsss_v8 Artwork Proof Date: 22.06.2018
- Number of artboards: 2
- Printing Details
- Print Colours,
Special Instructions
Please use 180gsm bbright white coated paper
DIMENSIONS:
FLAT SIZE: A3 SIZE – 420mm (WI x 297mm (HI)
FOLDED SIZE: AS SIZE – 210mm (WI x 148.5)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>