RIDGID Table Saw Instruction Manual

Table Saw

OPERATOR’S MANUAL
MANUEL D’UTILISATION MANUAL DEL OPERADOR
10 in. TABLE SAW
SCIE À TABLE de 254 mm (10 po) SIERRA DE MESA de 254 mm (10 pulg.)
R4514

To register your RIDGID product, please visit:
http://register.RIDGID.com
Pour enregistrer votre produit de RIDGID,
s’il vous plaît la visite : http://register.RIDGID.com
Para registrar su producto de RIDGID, por favor visita: http://register.RIDGID.com

Your saw has been engineered and manufactured to our high standard for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING:
To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.

SAVE THIS MANUAL FOR FUTURE REFERENCE

Cette scie a été conçue et fabriquée conformément aux strictes normes de fiabilité, simplicité d’emploi et sécurité d’utilisation. Correctement entretenu, cet outil vous donnera des années de fonctionnement robuste et sans problème.

Su sierra ha sido diseñado y fabricado de conformidad con nuestras estrictas normas para brindar fiabilidad, facilidad de uso y seguridad para el operador. Con el debido cuidado, le brindará muchos años de sólido funcionamiento y sin problemas.

AVERTISSEMENT :
Pour réduire les risques de blessures, l’utilisateur doit lire et veiller à bien comprendre le manuel d’utilisation avant d’employer ce produit.

ADVERTENCIA:
Para reducir el riesgo de lesiones, el usuario debe leer y comprender el manual del operador antes de usar este producto.

CONSERVER CE MANUEL POUR FUTURE RÉFÉRENCE

GUARDE ESTE MANUAL PARA FUTURAS CONSULTAS

TABLE OF CONTENTS TABLE DES MATIÈRES / ÌNDICE DE CONTENIDO
Introduction …………………………………………………………………………………………………………………………………………………. 2 Introduction / Introducción
General Safety Rules …………………………………………………………………………………………………………………………………..3-4 Règles de sécurité générales / Reglas de seguridad generales
Table Saw Safety Rules ……………………………………………………………………………………………………………………………….4-6 Règles de sécurité scie à table / Reglas de seguridad sierra de mesa
Additional Safety Rules …………………………………………………………………………………………………………………………………. 6 Règles de sécurité supplémentaires / Advertencias de seguridad adicionales
Symbols………………………………………………………………………………………………………………………………………………………. 7 Symboles / Símbolos
Electrical ……………………………………………………………………………………………………………………………………………………… 8 Caractéristiques électriques / Aspectos eléctricos
Glossary of Terms …………………………………………………………………………………………………………………………………………. 9 Glossaire / Glosario de términos
Features…………………………………………………………………………………………………………………………………………………10-12 Caractéristiques / Características
Tools Needed……………………………………………………………………………………………………………………………………………… 13 Outils nécessaires / Herramientas necesarias
Loose Parts ……………………………………………………………………………………………………………………………………………….. 14 Pièces détachées / Piezas sueltas
Assembly ……………………………………………………………………………………………………………………………………………….15-26 Assemblage / Armado
Operation……………………………………………………………………………………………………………………………………………….27-44 Utilisation / Funcionamiento
Adjustments……………………………………………………………………………………………………………………………………………45-50 Réglages / Ajustes
Maintenance …………………………………………………………………………………………………………………………………………..50-53 Entretien / Mantenimiento
Accessories ……………………………………………………………………………………………………………………………………………….. 53 Accessoires / Accesorios
Troubleshooting ………………………………………………………………………………………………………………………………………53-54 Dépannage / Solución de problemas
Warranty ……………………………………………………………………………………………………………………………………………………. 55 Garantie / Garantía
Parts Ordering and Service ……………………………………………………………………………………………………………….Back page Commande de pièces et réparation / Pedidos de piezas y servicio
INTRODUCTION INTRODUCTION / INTRODUCCIÓN
This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability have been given top priority in the design of this product making it easy to maintain and operate.

Ce produit offre de nombreuses fonctions destinées à rendre son utilisation plus plaisante et satisfaisante. Lors de la conception de ce produit, l’accent a été mis sur la sécurité, les performances et la fiabilité, afin d’en faire un outil facile à utiliser et à entretenir.

Este producto ofrece numerosas características para hacer más agradable y placentero su uso. En el diseño de este producto se ha conferido prioridad a la seguridad, el desempeño y la fiabilidad, por lo cual se facilita su manejo y mantenimiento.
2

GENERAL SAFETY RULES

WARNING:
Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/ or serious injury.
Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mainsoperated (corded) power tool or battery- operated (cordless) power tool.
WORK AREA SAFETY
Keep work area clean and well lit. Cluttered or dark areas invite accidents.
Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
ELECTRICAL SAFETY
Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
If operating a power tool in a damp location is unavoidable, use a ground fault circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric shock.
PERSONAL SAFETY
Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.

Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.
If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.
Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.
POWER TOOL USE AND CARE
Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
Disconnect the plug from the power source and/ or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.

3 – English

GENERAL SAFETY RULES

Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
SERVICE Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

TABLE SAW SAFETY RULES

BLADE GUARD, RIVING KNIFE AND ANTI-
KICKBACK PAWLS
Keep guards in place. Guards must be in working order and be properly mounted. A guard that is loose, damaged, or is not functioning correctly must be repaired or replaced.
Always use saw blade guard, riving knife and antikickback pawls for every through-cutting operation. For through-cutting operations where the saw blade cuts completely through the thickness of the workpiece, the guard and other safety devices help reduce the risk of injury.
Immediately reattach the guarding system after completing an operation (such as rabbeting, dadoing or resawing cuts) which requires removal of the guard, riving knife and/or anti-kickback pawls. The guard, riving knife, and anti- kickback pawls help to reduce the risk of injury.
Make sure the saw blade is not contacting the guard, riving knife or the workpiece before the switch is turned on. Inadvertent contact of these items with the saw blade could cause a hazardous condition.
Adjust the riving knife as described in this instruction manual. Incorrect spacing, positioning and alignment can make the riving knife ineffective in reducing the likelihood of kickback.
For the riving knife and anti-kickback pawls to work, they must be engaged in the workpiece. The riving knife and anti-kickback pawls are ineffective when cutting workpieces that are too short to be engaged with the riving knife and anti-kickback pawls. Under these conditions a kickback cannot be prevented by the riving knife and anti-kickback pawls.
Use the appropriate saw blade for the riving knife. For the riving knife to function properly, the saw blade diameter must match the appropriate riving knife and the body of the saw blade must be thinner than the thickness of the riving knife and the cutting width of the saw blade must be wider than the thickness of the riving knife.

CUTTING PROCEDURES
DANGER: Never place your fingers or hands in the vicinity or in line with the saw blade. A moment of inattention or a slip could direct your hand towards the saw blade and result in serious personal injury.
Feed the workpiece into the saw blade against the direction of rotation. Feeding the workpiece in the same direction that the saw blade is rotating above the table may result in the workpiece, and your hand, being pulled into the saw blade.
Never use the miter gauge to feed the workpiece when ripping and do not use the rip fence as a length stop when cross cutting with the miter gauge. Guiding the workpiece with the rip fence and the miter gauge at the same time increases the likelihood of saw blade binding and kickback.
When ripping, always apply the workpiece feeding force between the fence and the saw blade. Use a push stick when the distance between the fence and the saw blade is less than 150 mm, and use a push block when this distance is less than 50 mm. “Work helping” devices will keep your hand at a safe distance from the saw blade.
Use only the push stick provided by the manufacturer or constructed in accordance with the instructions. This push stick provides sufficient distance of the hand from the saw blade.
Never use a damaged or cut push stick. A damaged push stick may break causing your hand to slip into the saw blade.
Do not perform any operation “freehand”. Always use either the rip fence or the miter gauge to position and guide the workpiece. “Freehand” means using your hands to support or guide the workpiece, in lieu of a rip fence or miter gauge. Freehand sawing leads to misalignment, binding and kickback.
Never reach around or over a rotating saw blade. Reaching for a workpiece may lead to accidental contact with the moving saw blade.

4 – English

TABLE SAW SAFETY RULES

Provide auxiliary workpiece support to the rear and/or sides of the saw table for long and/or wide workpieces to keep them level. A long and/or wide workpiece has a tendency to pivot on the table’s edge, causing loss of control, saw blade binding and kickback.
Feed workpiece at an even pace. Do not bend or twist the workpiece. If jamming occurs, turn the tool off immediately, unplug the tool then clear the jam. Jamming the saw blade by the workpiece can cause kickback or stall the motor.
Do not remove pieces of cut-off material while the saw is running. The material may become trapped between the fence or inside the saw blade guard and the saw blade pulling your fingers into the saw blade. Turn the saw off and wait until the saw blade stops before removing material.
Use an auxiliary fence in contact with the table top when ripping workpieces less than 2 mm thick. A thin workpiece may wedge under the rip fence and create a kickback.
KICKBACK
Kickback is a sudden reaction of the workpiece due to a pinched, jammed saw blade or misaligned line of cut in the workpiece with respect to the saw blade or when a part of the workpiece binds between the saw blade and the rip fence or other fixed object.
Most frequently during kickback, the workpiece is lifted from the table by the rear portion of the saw blade and is propelled towards the operator.
Kickback is the result of saw misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below.
Never stand directly in line with the saw blade. Always position your body on the same side of the saw blade as the fence. Kickback may propel the workpiece at high velocity towards anyone standing in front and in line with the saw blade.
Never reach over or in back of the saw blade to pull or to support the workpiece. Accidental contact with the saw blade may occur or kickback may drag your fingers into the saw blade.
Never hold and press the workpiece that is being cut off against the rotating saw blade. Pressing the workpiece being cut off against the saw blade will create a binding condition and kickback.
Align the fence to be parallel with the saw blade. A misaligned fence will pinch the workpiece against the saw blade and create kickback.
Use a featherboard to guide the workpiece against the table and fence when making non-through cuts such as rabbeting, dadoing or resawing cuts. A featherboard helps to control the workpiece in the event of a kickback.

Use extra caution when making a cut into blind areas of assembled workpieces. The protruding saw blade may cut objects that can cause kickback.
Support large panels to minimize the risk of saw blade pinching and kickback. Large panels tend to sag under their own weight. Support(s) must be placed under all portions of the panel overhanging the table top.
Use extra caution when cutting a workpiece that is twisted, knotted, warped or does not have a straight edge to guide it with a miter gauge or along the fence. A warped, knotted, or twisted workpiece is unstable and causes misalignment of the kerf with the saw blade, binding and kickback.
Never cut more than one workpiece, stacked vertically or horizontally. The saw blade could pick up one or more pieces and cause kickback.
When restarting the saw with the saw blade in the workpiece, centre the saw blade in the kerf so that the saw teeth are not engaged in the material. If the saw blade binds, it may lift up the workpiece and cause kickback when the saw is restarted.
Keep saw blades clean, sharp, and with sufficient set. Never use warped saw blades or saw blades with cracked or broken teeth. Sharp and properly set saw blades minimise binding, stalling and kickback.
TABLE SAW OPERATION Turn off the table saw and disconnect the power
cord when removing the throat plate, changing the saw blade or making adjustments to the riving knife, anti-kickback pawls or blade guard, and when the machine is left unattended. Precautionary measures will avoid accidents.
Never leave the table saw running unattended. Turn it off and don’t leave the tool until it comes to a complete stop. An unattended running saw is an uncontrolled hazard.
Locate the table saw in a well-lit and level area where you can maintain good footing and balance. It should be installed in an area that provides enough room to easily handle the size of your workpiece. Cramped, dark areas, and uneven slippery floors invite accidents.
Frequently clean and remove sawdust from under the saw table and/or the dust collection device. Accumulated sawdust is combustible and may self-ignite.
The table saw must be secured. A table saw that is not properly secured may move or tip over.
Remove tools, wood scraps, etc. from the table before the table saw is turned on. Distraction or a potential jam can be dangerous.
Always use saw blades with correct size and shape (diamond versus round) of arbour holes. Saw blades that do not match the mounting hardware of the saw will run off-centre, causing loss of control.

5 – English

TABLE SAW SAFETY RULES

Never use damaged or incorrect saw blade mounting means such as flanges, saw blade washers, bolts or nuts. These mounting means were specially designed for your saw, for safe operation and optimum performance.
Never stand on the table saw, do not use it as a stepping stool. Serious injury could occur if the tool is tipped or if the cutting tool is accidentally contacted.

Make sure that the saw blade is installed to rotate in the proper direction. Do not use grinding wheels, wire brushes, or abrasive wheels on a table saw. Improper saw blade installation or use of accessories not recommended may cause serious injury.

ADDITIONAL SAFETY RULES

Know your power tool. Read the operator’s manual carefully. Learn the saw’s applications and limitations as well as the specific potential hazards related to this tool.
Make workshop childproof with padlocks and master switches, or by removing starter keys.
Use the proper extension cord. Make sure your extension cord is in good condition. Use only a cord heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. A wire gauge size (A.W.G.) of at least 14 is recommended for an extension cord 25 feet or less in length. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.
Always wear eye protection with side shields marked to comply with ANSI Z87.1. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury.
Secure work. Use clamps or a vise to hold work when practical. It’s safer than using your hand and frees both hands to operate tool.
Use recommended accessories. Consult the operator’s manual for recommended accessories. The use of improper accessories may risk injury.
Use only correct blades. Do not use blades with incorrect size holes. Never use blade washers or blade bolts that are defective or incorrect. The maximum blade capacity of your saw is 10 in. (254 mm).
Check damaged parts. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged must be properly repaired or replaced by an authorized service center to avoid risk of personal injury.
Never leave tool running unattended. Turn the power off. Don’t leave tool until it comes to a complete stop.

Protect your lungs. Wear a face or dust mask if the cutting operation is dusty.
Protect your hearing. Wear hearing protection during extended periods of operation.
When operating a power tool outside, use an outdoor extension cord marked “W-A” or “W”. These cords are rated for outdoor use and reduce the risk of electric shock.
Always keep the blade guard and riving knife (splitter) in place and in working order.
Keep hands away from cutting area. Keep hands away from blades. Do not reach underneath work or around or over the blade while blade is rotating. Do not attempt to remove cut material when blade is moving.
Avoid awkward operations and hand positions where a sudden slip could cause your hand to move into the blade.
Do not reach behind the blade with either hand from either side of the saw blade, to support the workpiece, remove wood scraps, or for any other reason while the blade is spinning.
The table saw must be mounted to a firm supporting surface, such as a workbench or leg stand that positions the saw at waist height. In addition, provide adequate support such as auxiliary tables, roller support tables, outfeed supports, etc. when cutting heavy, wide, or long . Heavy, wide, or long workpieces can tip if not securely supported. If the cut-off piece or workpiece tips, it can lift the blade guard or be thrown by the spinning blade.
If the workpiece or blade becomes jammed, turn the table saw off. Wait for all moving parts to stop and disconnect the plug from the power source. Then work to free the jammed material. After the material is removed, verify that the blade is parallel to the miter gauge groove, and the riving knife and blade are aligned. If the jam occurred during a rip cut, verify that the rip fence is parallel to the blade. Adjust if necessary.

6 – English

SYMBOLS

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL

MEANING

DANGER:

Indicates a hazardous situation, which, if not avoided, will result in death or serious injury.

WARNING:

Indicates a hazardous situation, which, if not avoided, could result in death or serious injury.

CAUTION: NOTICE:

Indicates a hazardous situation, that, if not avoided, may result in minor or moderate injury.
(Without Safety Alert Symbol) Indicates information considered important, but not related to a potential injury (e.g. messages relating to property damage).

Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.

SYMBOL

NAME

DESIGNATION/EXPLANATION

Safety Alert

Indicates a potential personal injury hazard.

Read Operator’s Manual

To reduce the risk of injury, user must read and understand operator’s manual before using this product.

Eye Protection No Hands Symbol

Always wear eye protection with side shields marked to comply with ANSI Z87.1.
Failure to keep your hands away from the blade will result in serious personal injury.

Wet Conditions Alert

Do not expose to rain or use in damp locations.

V A Hz min
no
…/min

Volts Amperes Hertz Minutes Alternating Current No Load Speed Class II Construction Per Minute

Voltage Current Frequency (cycles per second) Time Type of current Rotational speed, at no load Double-insulated construction Revolutions, strokes, surface speed, orbits, etc., per minute

7 – English

ELECTRICAL

DOUBLE INSULATION
Double insulation is a concept in safety in electric power tools, which eliminates the need for the usual three-wire grounded power cord. All exposed metal parts are isolated from the internal metal motor components with protecting insulation. Double insulated tools do not need to be grounded.
WARNING:
The double insulated system is intended to protect the user from shock resulting from a break in the tool’s internal wiring. Observe all normal safety precautions to avoid electrical shock.
NOTE: Servicing of a product with double insulation requires extreme care and knowledge of the system and should be performed only by a qualified service technician. For service, we suggest you return the tool to your nearest authorized service center for repair. Always use original factory replacement parts when servicing.
ELECTRICAL CONNECTION
This tool has a precision-built electric motor. It should be connected to a power supply that is 120 V, AC only (normal household current), 60 Hz. Do not operate this tool on direct current (DC). A substantial voltage drop will cause a loss of power and the motor will overheat. If the tool does not operate when plugged into an outlet, double check the power supply.
POLARIZED PLUGS
See Figure 1.
To reduce the risk of electric shock, this tool has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.
EXTENSION CORDS
When using a power tool at a considerable distance from a power source, be sure to use an extension cord that has the capacity to handle the current the product will draw. An undersized cord will cause a drop in line voltage, resulting in overheating and loss of power. Use the chart to determine the minimum wire size required in an extension cord. Only round jacketed cords listed by Underwriter’s Laboratories (UL) should be used.

When working outdoors with a product, use an extension cord that is designed for outside use. This type of cord is designated with “WA” or “W” on the cord’s jacket.
Before using any extension cord, inspect it for loose or exposed wires and cut or worn insulation.

**Ampere rating (on tool faceplate)

0-2.0 2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0

Cord Length

Wire Size (A.W.G.)

25′

16 16 16 16 14 14

50′

16 16 16 14 14 12

100′

16 16 14 12 10 —

**Used on 12 gauge – 20 amp circuit. NOTE: AWG = American Wire Gauge

WARNING:
Keep the extension cord clear of the working area. Position the cord so that it will not get caught on lumber, tools or other obstructions while you are working with a power tool. Failure to do so can result in serious personal injury.

WARNING:
Check extension cords before each use. If damaged replace immediately. Never use product with a damaged cord since touching the damaged area could cause electrical shock resulting in serious injury.

POLARIZED PLUG

Fig. 1

8 – English

GLOSSARY OF TERMS

Anti-Kickback Pawls (radial arm and table saws) A device which, when properly installed and maintained, is designed to stop the workpiece from being kicked back toward the front of the saw during a ripping operation. Arbor The shaft on which a blade or cutting tool is mounted. Bevel Cut A cutting operation made with the blade at any angle other than 90° to the table surface. Chamfer A cut removing a wedge from a block so the end (or part of the end) is angled rather than at 90°. Compound Cut A cross cut made with both a miter and a bevel angle. Cross Cut A cutting or shaping operation made across the grain or the width of the workpiece. Cutter Head (planers and jointer planers) A rotating cutterhead with adjustable blades or knives. The blades or knives remove material from the workpiece. Dado Cut (table saws and compound sliding miter saws) A non-through cut which produces a square, three-sided notch or trough in the workpiece. Featherboard (table saws) A device used to help control the workpiece by guiding it securely against the table or fence during any ripping operation. FPM or SPM Feet per minute (or strokes per minute), used in reference to blade movement. Freehand Performing a cut without the workpiece being guided by a fence, miter fence, or other aids. Gum A sticky, sap-based residue from wood products. Heel Alignment of the blade to the miter gauge groove. Kerf The material removed by the blade in a through cut or the slot produced by the blade in a non-through or partial cut. Kickback A hazard that can occur when the blade binds or stalls, throwing the workpiece in the direction of the spinning blade. Miter Cut A cutting operation made with the workpiece at any angle to the blade other than 90°. Non-Through Cuts (table saws and compound sliding miter saws) Any cutting operation where the blade does not extend completely through the thickness of the workpiece. This is a cut where the blade will not cut the workpiece into two pieces.

Pilot Hole (drill presses and scroll saws) A small hole drilled in a workpiece that serves as a guide for drilling large holes accurately or for insertion of a scroll saw blade. Push Blocks (jointer planers) Device used to feed the workpiece over the jointer planer cutterhead during any operation. This aid helps keep the operator’s hands well away from the cutterhead. Push Blocks and Push Sticks (table saws) Devices used to feed the workpiece through the saw blade during cutting operations. When making a narrow rip cut without a jig or similar cutting aid, always use a push stick (not a push block). A push block can be used for narrow ripping operations, if a jig or similar cutting aid is used. These aids help keep the operator’s hands well away from the blade. Rabbet A non-through cut positioned on the end or edge of the workpiece which produces a square, two-sided notch or trough in the workpiece. Resaw (table saws and band saws) A cutting operation to reduce the thickness of the workpiece to make thinner pieces. Resin A sticky, sap-based substance that has hardened. Revolutions Per Minute (RPM) The number of turns completed by a spinning object in one minute. Ripping or Rip Cut (table saws) A cutting operation along the length of the workpiece and typically in the direction of the grain. Riving Knife/Spreader/Splitter (table saws) A metal piece, slightly thinner than the blade, which helps keep the kerf open and also helps to prevent kickback. Saw Blade Path The area over, under, behind, or in front of the blade. As it applies to the workpiece, that area which will be or has been cut by the blade. Snipe (planers) Depression made at either end of a workpiece by cutter blades when the workpiece is not properly supported. Taper Cut A cut where the material being cut has a different width at the beginning of the cut from the end. Through Sawing Any cutting operation where the blade extends completely through the thickness of the workpiece. This type of cut will separate a single workpiece into two pieces. Workpiece or Material The item on which the operation is being done. Worktable Surface where the workpiece rests while performing a cutting, drilling, planing, or sanding operation.

9 – English

FEATURES

PRODUCT SPECIFICATIONS
Blade Diameter………………………………………………….. 10 in. Blade Arbor ………………………………………………………5/8 in. Cutting Depth at 90°………………………………………. 3-1/2 in.

Cutting Depth at 45°………………………………………. 2-1/2 in. Rating …………………………………….120 V~, 15 Amps, 60 Hz No Load Speed ………………………………….5,000/min (RPM)

ANTI-KICKBACK PAWLS

RIVING KNIFE

BLADE GUARD ASSEMBLY SAW BLADE

LOW FENCE

MITER GAUGE

RIP FENCE

CORD WRAP

BEVEL INDICATOR

SWITCH ASSEMBLY
BEVEL ADJUSTING HANDWHEEL

LEG STAND

LOCKING LEVER FRONT RAIL
BEVEL LOCKING
LEVER

BEVEL SCALE BLADE HEIGHT LOCK KNOB

GRIPS

HEIGHT ADJUSTING
KNOB

10 – English

Fig. 2

FEATURES

RIP FENCE STORAGE AREA

PUSH STICK AND MITER GAUGE STORAGE AREA

DUST CHUTE

RIVING KNIFE, BLADE WRENCH, ANTIKICKBACK PAWLS
AND BLADE GUARD STORAGE AREA

Fig. 3

KNOW YOUR TABLE SAW
See Figures 2 – 3.

BLADE – For maximum performance, it is recommended that you use the 10 in. carbide tipped combination blade

The safe use of this product requires an understanding of the information on the tool and in this operator’s manual as well as a knowledge of the project you are attempting. Before use of this product, familiarize yourself with all operating features and safety rules.

provided with your saw. The blade is raised and lowered with the height adjusting knob . Bevel angles are locked with the bevel locking lever. Additional blade styles of the same high quality are available for specific operations such as ripping. Your local dealer can provide you with complete information.

ACCESSORY STORAGE – Convenient storage areas for the push stick, riving knife, wrenches, blade guard, miter gauge,

Blade kerf width must be within the limits stamped on the riving knife.

anti-kickback pawls, and rip fence are located underneath

the saw table.

WARNING:

ANTI-KICKBACK PAWLS – Kickback is a hazard in which the workpiece is thrown back toward the operator. The teeth on the removable anti-kickback pawls point away from the workpiece. If the workpiece should be pulled back toward

Do not use blades rated less than the speed of this tool. Failure to heed this warning could result in personal injury.

the operator, the teeth dig into the wood to help prevent or reduce the possibility of kickback.
BEVEL ADJUSTING HANDWHEEL – Located on the front of the saw, this handwheel is used to make the adjustment for bevel angles.
BEVEL LOCKING LEVER – This lever under the worktable surface on the front of the saw, locks the angle setting of the blade.
BEVEL SCALE – The easy-to-read scale on the front of the saw shows the exact blade angle.

BLADE GUARD – Always keep the guard down over the blade for through-sawing cuts.
BLADE HEIGHT LOCK KNOB – This knob, in the center of the bevel adjusting handwheel, locks the height of the blade.
ELECTRIC BRAKE – An electric brake has been provided to stop blade rotation after the saw is turned off.
HEIGHT ADJUSTING KNOB – Located on the front of the saw, this knob is used to lower and raise the blade for adjustments or blade replacement.

11 – English

FEATURES

LOCKING LEVER – The lever on the front of the rip fence releases the rip fence or locks it in place.
MITER GAUGE – This miter gauge aligns the workpiece for a cross cut. The easy- to-read indicator shows the exact angle for a miter cut, with positive stops at 90° and 45°.
MITER GAUGE GROOVES – The miter gauge rides in these grooves on either side of the blade.
RAILS – Front and rear rails provide support for the rip fence.
RIP FENCE – A sturdy metal fence guides the workpiece and is secured with the locking lever. Grooves run along the top and sides of the rip fence for use with optional clamps and accessories.
NOTE: The low fence should only face the blade when cutting narrow material that is 3/4 inches thick or less.
RIVING KNIFE – A removable metal piece of the blade guard assembly, slightly thinner than the saw blade, which helps keep the kerf open and prevent kickback. When in the through sawing, or “up” position, it is higher than the saw blade. When in the non-through sawing, or “down” position, it is below the saw blade teeth.
RIP SCALE – Located on the front rail, the easy-to-read scale provides precise measurements for rip cuts.
SWITCH ASSEMBLY – This saw has an easy access switch assembly located below the front rail. To lock the switch, install a padlock (not included) through the holes in the switch and cover. Make certain the switch is inoperable. If the switch is still operable with the padlock installed, a padlock with a larger shackle diameter must be used. Store the padlock key in another location.
TABLE EXTENSION – Located on the side of the saw table, the table extension gives the operator additional support when cutting wide workpieces.

NOTE: The switch cover does not have to be raised to operate the switch. TO TURN YOUR SAW ON: Press the top button on the switch to turn the saw on.
NOTE: If AC power is disconnected or interrupted while the saw is running, the saw will turn off. To restart the saw, restore AC power and press the top of the switch. TO TURN YOUR SAW OFF: Press the bottom button on the switch to turn the saw off. TO LOCK YOUR SAW: With the saw turned off, install a padlock (not included) through the holes in the switch and switch cover.
WARNING:
ALWAYS make sure your workpiece is not in contact with the blade before operating the switch to start the tool. Failure to heed this warning could cause the workpiece to be kicked back toward the operator and result in serious personal injury.
WARNING:
To reduce the risk of accidental starting, always make sure the top button on the switch is not depressed before plugging tool into the power source.

OPERATING COMPONENTS
The upper portion of the blade projects up through the table and is surrounded by an insert called the throat plate. The height of the blade is set with a handwheel on the front of the saw. To accommodate wide panels, the saw table has rails on each side. Detailed instructions are provided in the Operation section of this manual for the basic cuts: cross cuts, miter cuts, bevel cuts, and compound cuts.
The rip fence is used to position work for lengthwise cuts. A scale on the front rail shows the distance between the rip fence and the blade.
It is very important to use the blade guard assembly for all through-sawing operations. The blade guard assembly includes: riving knife, anti-kickback pawls, and plastic blade guard.

SWITCH ON

SWITCH OFF

SWITCH ASSEMBLY
See Figure 4.
This saw is equipped with an on/off switch that has a built-in locking feature. This feature is intended to prevent unauthorized and possible hazardous use by children and others.

SWITCH IN LOCKED POSITION

Fig. 4

12 – English

TOOLS NEEDED
The following tools (not included or drawn to scale) are needed for assembly and adjustments:
FRAMING SQUARE

COMBINATION SQUARE

C-CLAMPS

FLATHEAD SCREWDRIVER PHILLIPS SCREWDRIVER
ADJUSTABLE WRENCH

Fig. 5

13 – English

LOOSE PARTS LIST

The following items are included with your table saw: B

A

C

D

E

G H

I1
K I2 F

L J

Fig. 6

A. Anti-kickback Pawls ………………………………………… 1

F. Hardware Bag (continued)

B. Rip Fence……………………………………………………….. 1 C. Blade Guard……………………………………………………. 1

Hex Key (4 mm and 5 mm) ……………………………. 2 Small Spacer……………………………………………….. 4

D. Miter Gauge ……………………………………………………. 1 E. Push Stick………………………………………………………. 1

G. Upper Tube …………………………………………………….. 1 H. Center Brace…………………………………………………… 1

F. Hardware Bag

I. Multiple Items

Lock Nut (M8) ……………………………………………… 8 Flat Washer (ID10 x OD18 x 1.6t)……………………. 2

I1. Right Handle……………………………………………… 1 I2. Left Handle ……………………………………………….. 1

Flat Washer (ID13.5 x OD32 x 1.6t)…………………. 2 Large Spacer……………………………………………….. 2

J. Wheel …………………………………………………………….. 2 K. Inner Leg Assembly …………………………………………. 1

Carriage Bolt (M8 x 80 mm)…………………………… 6 Bolt (M6 x 70 mm)………………………………………… 4

L. Foot Assembly ………………………………………………… 2 NOT SHOWN

Bolt (M6 x 40 mm)………………………………………… 2 Hex Nut (M6)……………………………………………….. 6

Blade Wrenches (open end and closed end)

14 – English

ASSEMBLY
UNPACKING
This product requires assembly. Carefully lift the saw from the carton and place it on a
level work surface. NOTE: This tool is heavy. To avoid back injury, keep your knees bent and lift with your legs, not your back, and get help when needed.
WARNING:
Do not use this product if any parts on the Loose Parts List are already assembled to your product when you unpack it. Parts on this list are not assembled to the product by the manufacturer and require customer installation. Use of a product that may have been improperly assembled could result in serious personal injury.
Inspect the tool carefully to make sure no breakage or damage occurred during shipping.
Do not discard the packing material until you have carefully inspected and satisfactorily operated the tool. NOTE: Remove the foam block from between the saw’s table and the motor by first beveling the blade, refer to To Change Blade Angle in the Operation section of this manual.
The saw is factory set for accurate cutting. After assembling it, check for accuracy. If shipping has influenced the settings, refer to specific procedures explained in this manual.
If any parts are damaged or missing, please call 1-866-539-1710 for assistance.
WARNING:
If any parts are damaged or missing, do not operate this tool until the parts are replaced. Use of this product with damaged or missing parts could result in serious personal injury.

WARNING:
Do not attempt to modify this tool or create accessories not recommended for use with this tool. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury.
WARNING:
Do not connect to power supply until assembly is complete. Failure to comply could result in accidental starting and possible serious personal injury.
WARNING:
Do not lift the saw without help. Hold it close to your body. Keep your knees bent and lift with your legs, not your back. Ignoring these precautions can result in back injury.
WARNING:
Never stand directly in line with the blade or allow hands to come closer than 3 in. to the blade. Do not reach over or across the blade. Failure to heed this warning can result in serious personal injury.
WARNING:
To avoid serious personal injury, always make sure the table saw is securely mounted to a workbench or an approved leg stand. NEVER operate the saw on the floor.

15 – English

ASSEMBLY
ASSEMBLING THE LEG STAND
See Figures 7 – 13.
NOTE: Do not use this leg stand with other equipment or for other purposes.
Many of the leg stand parts are movable. All hardware must be tightened securely but not so tight that the leg stand won’t open and close. For easier assembly, match number to number and fingertighten all fasteners. Only tighten fasteners securely when you are sure the release lever locks over the center brace. Align handle with holes in the end of the upper tube and
insert. Secure in place using a bolt (M6 x 40 mm) and hex nut (M6). Repeat for other side. Place the center brace on top of the inner leg assembly (curve side up) with the stop pin under the pedal assembly latch.
NOTE: The stop pins rest on top of inner leg assembly. Insert a carriage bolt (M8 x 80 mm) through the top hole
of the inner leg assembly then slide a large spacer on the bolt. Repeat for the other side. Slide the center brace onto the bolt and secure in place using a lock nut (M8). Repeat for the other side.
NUMBERS

6

6

BOLT

UPPER TUBE

HEX NUT

RIGHT HANDLE

CENTER BRACE

LEFT HANDLE

Fig. 8

LOCK NUT

LARGE SPACER

CARRIAGE BOLT

6 6
Fig. 7

STOP PIN

INNER LEG ASSEMBLY
Fig. 9

16 – English

ASSEMBLY

With the curve handle turned downward, secure the upper tubes to the leg stand using carriage bolt (M8 x 80 mm), small spacers, and lock nuts (M8).
Remove the bolts, spacers, and lock nuts from the foot assemblies.
Place the feet onto the leg stand. Align the holes in the feet with the holes in the leg stand.
Slide a spacer onto each bolt and insert bolts through the holes in the feet and leg stand.
Install nuts and loosely tighten.
UPPER TUBE

Slide the flat washer (ID13.5 x OD32 x 1.6t), wheel, and flat washer (ID10 x OD18 x 1.6t) onto the axle through the hole in the center of the wheel. Secure in place using lock nut (M8).
Repeat with the second wheel.
Before use, verify the release lever locks the leg stand securely and tighten all screws. If the leg stand will not lock, do not use; contact an authorized service center for assistance.

LOCK NUT

SMALL SPACER

SMALL SPACER

WHEEL

CARRIAGE BOLT
LEG STAND NUT FOOT

Fig. 10

LOCK NUT

FLAT WASHER, LARGE
FLAT WASHER, SMALL

RELEASE LEVER

Fig. 12 CENTER BRACE

SPACER BOLT

Fig. 11 17 – English

Fig. 13

ASSEMBLY
MOUNTING HOLES
The table saw must be mounted to a firm supporting surface such as a workbench or leg stand. Four bolt holes have been provided in the saw’s base for this purpose. Each of the four mounting holes should be bolted securely using 1/4 in. carriage bolts, washers, lock washers, and wing nuts. Bolts should be of sufficient length to accommodate the saw base, washers, lock washers, wing nuts, and the thickness of the workbench. Tighten all four bolts securely. Carefully check the workbench after mounting to make sure that no movement can occur during use. If any tipping, sliding, or walking is noted, secure the workbench to the floor before operating.
MOUNTING THE TABLE SAW TO THE LEG STAND
See Figure 14.
WARNING:
Do not lift the saw without help. The saw weighs approximately 80 lbs. Hold it close to your body. Keep your knees bent and lift with your legs, not your back. Ignoring these precautions can result in back injury.
Open leg stand as described on page 26. Place saw base on the leg stand. Align the holes in the
saw base with the holes in the stand. Insert a bolt (M6 x 70 mm) through the hole in the table
saw and into the hole in the stand. Hand tighten using hex nut (M6). For the remaining holes, insert the bolts through the hole in the saw base and into the hole in the stand, then secure to the stand using a hex nut. Tighten all hardware with a wrench and hex key. You may find it helpful to use a wrench to hold the nut and the hex key to tighten the bolt.

BOLT
SAW BASE HEX NUT
Fig. 14

18 – English

ASSEMBLY
TO REMOVE/INSTALL/ALIGN THE THROAT PLATE
See Figures 15 – 16.
WARNING:
If the throat plate is too high or too low, the workpiece can catch on the uneven edges resulting in binding or kickback which could result in serious personal injury. Verify the throat plate is correctly seated. Before turning on the saw, perform a dry run of the cutting operation to make sure that no problems will occur when the cut is made. If the workpiece catches, do not attempt to use the saw. Contact customer service for assistance.
Lower the saw blade by turning the height adjusting knob counterclockwise.
To remove the throat plate, rotate the knob to the unlocked position. Place your index finger into the hole, lift and pull the throat plate out toward the front of the saw.
To reinstall the throat plate, rotate the knob to the unlocked position. Place throat plate back onto the saw and rotate the knob to the locked position. NOTE: The throat plate may move up and down over time. If necessary, use a 2 mm hex key to adjust the screws in the throat plate until it is level with the saw table.

THROAT PLATE

UNLOCK HOLE

SCREWS

LOCK KNOB
Fig. 15
Fig. 16

19 – English

ASSEMBLY

TO CHANGE RIVING KNIFE POSITIONS
See Figure 17.
This saw is shipped with a riving knife that should be placed in the “down” position for non-through cutting and must be placed in the “up” position for all other cutting operations.

RELEASE LEVER
(UNLOCKED)

CAUTION:
Use caution when reaching inside the throat in the saw table. Blade contact, even when the blade is still, may result in injury to hands or arms.
Unplug the saw.
To place in the “up” position for all through cutting: Remove the throat plate. Raise the saw blade by turning the height adjusting knob
clockwise. Unlock the release lever by pulling it up. Grasp the riving knife and pull it towards the right side of
the saw to release the riving knife from the spring-loaded riving clamp. Pull the riving knife up until the internal pins are engaged and the riving knife is above the saw blade. Lock the release lever by pushing the lever down.

IN “UP” POSITION FOR THROUGH CUTTING RELEASE LEVER (LOCKED)

WARNING:
Make sure the release lever is fully seated. If the release lever is difficult to lock, thoroughly clean lever components using compressed air or a clean soft cloth as described in the Cleaning the Riving Knife Lock Lever Plates section in Maintenance. Failure to completely lock the release lever can allow the riving knife to change position during saw use, which could result in serious personaly injury.
Reinstall the throat plate.
To place in the “down” position for all non-through cutting: Remove the throat plate. Raise the saw blade by turning the height adjusting knob
clockwise. Unlock the release lever by pulling it up.

IN “DOWN” POSITION FOR NON-THROUGH CUTTING
Fig. 17
Grasp the riving knife and pull it towards the right side of the saw to release the riving knife from the spring-loaded riving clamp.
Push the riving knife down until it is below the saw blade. Lock the release lever by pushing the lever down. Reinstall the throat plate.

20 – English

ASSEMBLY

TO CHECK SAW BLADE INSTALLATION
See Figure 18.
NOTICE:
To work properly, the saw blade teeth must point down toward the front of the saw. Failure to heed this warning could cause damage to the saw blade, the saw, or the workpiece.
Unplug the saw. Remove blade wrenches from storage area by unscrewing
wing nut. Lower the saw blade and remove the throat plate. Raise the saw blade to its full height by turning the height
adjusting knob clockwise. Make sure the bevel locking lever is securely pushed to
the left. Place riving knife in “up” position. To loosen the blade: Using the left blade wrench, insert the open end onto the
flats on the arbor shaft. Insert the closed end of the other wrench over the hex
nut. Holding both wrenches firmly, pull the outside wrench (right side) forward while pushing the inside (left side) to the back of the saw. NOTE: Arbor shaft has right-hand threads.

BLADE WRENCH
(LEFT)

BLADE WRENCH (RIGHT)

HEX NUT
Fig. 18
To tighten the blade: Using the left blade wrench, insert the open end onto the
flats on the arbor shaft. Insert the closed end of the other blade wrench over the
hex nut. Holding both wrenches firmly, push the right wrench to the back of the machine. Make sure the blade nut is securely tightened. Do not overtighten. NOTE: Arbor shaft has right-hand threads. Reinstall the throat plate. Check all clearances for free blade rotation. After installation, adjust the rip scale indicator to account for the kerf and thickness of the blade. Refer to To Set the Rip Fence Scale Indicator to the Blade in the Operation section of this manual. In cutting operations, the scale will be set to the side of the blade where the cut will be measured and made.

21 – English

ASSEMBLY

TO INSTALL THE ANTI-KICKBACK PAWLS AND BLADE GUARD
See Figures 19 – 20.
WARNING:
Always install the blade guard and anti-kickback pawls onto the riving knife in the “up” position to provide proper blade coverage. Installing the guarding components onto the riving knife in any other position will prevent them from working as designed, which could increase the risk of serious personal injury.

PAWL HANDLE ANTI-KICKBACK PAWLS

BUTTON

WARNING:
Replace dull or damaged anti-kickback pawls. Dull or damaged pawls may not stop a kickback increasing the risk of serious personal injury.
NOTE: Anti-kickback pawls should only be installed for through cuts. Unplug the saw. Raise the saw blade by turning the height adjusting knob
clockwise. Place riving knife in “up” position. Reinstall the throat plate.
To install anti-kickback pawls: Press and hold the button on the right side of the anti-
kickback pawls. Align the slot in the pawls over rear notch in the riving knife. Push the pawl handle down snapping it into place and
release the button.
NOTE: Pull on the handle to make sure pawls are securely locked.
To install blade guard: Lift the guard lever up to unlock. With the front of the blade guard raised and the guard
lever unlocked, lower the back of the guard into the middle slot of the riving knife. Push the front of the guard down until the bar inside the guard is parallel to the table (see figure 20). If the bar is not parallel to the table, the riving knife is not in the “up” position. Lock the guard in place by pushing the guard lever down. The blade guard side barriers may be lifted, then positioned out of the way without being removed for easier measurement.
NOTE: Blade alignment can be adjusted for different kerf widths. Refer to: To Check and Align the Riving Knife and Saw Blade. Check the blade guard assembly for clearances and free movement.

BLADE GUARD

22 – English

RIVING KNIFE

TO LOCK

CORRECT INCORRECT

GUARD LEVER
Fig. 19
Fig. 20

ASSEMBLY

TO CHECK AND ALIGN THE RIVING KNIFE AND SAW BLADE
See Figure 21 – 22.
To check alignment of the riving knife: Unplug the saw. Raise the saw blade by turning the height adjusting knob
clockwise. Adjust the bevel angle to 0° and lock the bevel locking
lever. Remove the anti-kickback pawls and blade guard
assembly. To check horizontal alignment, place a framing square
or straight edge against both the body of the saw blade and the riving knife. The framing square should contact both the blade body and riving knife evenly with no gaps. Check the alignment with both sides of the blade body.
NOTE: The kerf or width of each tooth is wider than the blade body. When the riving knife is properly aligned, it will be centered on the kerf width.
To check vertical alignment, place a framing square beside the riving kife. The edge of the square and the riving knife should be parallel.
If the riving knife is out of alignment with the saw blade, adjustment is needed. The riving knife must be in alignment front to back (horizontally) and top to bottom (vertically).

To adjust (horizontally and vertically): Remove the anti-kickback pawls, blade guard assembly,
and throat plate. To make horizontal adjustments – Use a 5 mm hex key
to loosen the horizontal adjustment screws holding the mounting bracket. Reposition the riving knife left or right. Tighten horizontal adjustment screws and check alignment. Repeat as needed. To make vertical adjustments – Loosen the horizontal adjustment screws 1/4 turn. Use a 2.5 mm hex key to slowly turn the vertical adjustment screws until the riving knife is aligned with the blade. Tighten horizontal adjustment screws and check alignment. Repeat as needed. Replace the anti-kickback pawls, blade guard assembly, and throat plate.

ADJUSTMENT SCREWS
(VERTICAL)

ADJUSTMENT SCREWS
(HORIZONAL)

RIVING KNIFE

BLADE

BLADE TOOTH

BLADE BODY

RIVING KNIFE

KERF WIDTH
BLADE BODY

RIVING KNIFE

HORIZONTAL ADJUSTMENT

BLADE TOOTH

Fig. 21 23 – English

VERTICAL ADJUSTMENT

Fig. 22

ASSEMBLY
STORING TABLE SAW ACCESSORIES
See Figures 23 – 26. When not in use the rip fence, riving knife, wrenches, blade guard, miter gauge, anti-kickback pawls, and push stick may be stored beneath the saw table. These items must be secured prior to closing the leg stand and moving the saw.
BLADE GUARD

ANTI-KICKBACK PAWLS / BLADE GUARD
STORAGE

Fig. 23

PUSH STICK
PUSH STICK STORAGE

MITER GAUGE STORAGE

MITER GAUGE Fig. 25

RIP FENCE

ANTIKICKBACK
PAWLS BLADE
WRENCHES

RIVING KNIFE
WING NUT
Fig. 24

RIP FENCE STORAGE

Fig. 26

24 – English

ASSEMBLY

TO CLOSE/OPEN THE LEG STAND
See Figures 27 – 32. Remove any workpieces from the tool. Remove and securely store any tools or accessories such
as rip fence, miter gauge, clamps, blade guard, etc. Lower the saw blade.
To close the leg stand: At the same time, step on the release lever, grasp the
grips, and lift the grips up and away from the body. Continue lifting up on the grips until the release lever
clicks and locks into place.

To move the leg stand: Holding the grips firmly, pull grips toward you until the
leg stand and saw are balanced on the wheels.
Push the saw to the desired location then either open the leg stand for saw operation or store the saw in a dry environment.

RELEASE LEVER

Fig. 27

25 – English

Fig. 28 Fig. 29

ASSEMBLY
To open the leg stand: Grasp the grips on the saw table and stand it upright as
shown below. Step on the release lever and pull the grips toward you
at the same time. Once the leg stand is released from the release lever,
ease the leg stand toward the floor by pushing the grips toward the floor. With your hands on the grips, push the leg stand towards the ground until the table saw is in an open position. NOTE: The release lever will close over the center brace locking the leg stand in an open position.
GRIPS

RELEASE LEVER

LEG STAND

Fig. 30

RELEASE LEVER

26 – English

Fig. 31
CENTER BRACE
Fig. 32

OPERATION

WARNING:
Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury.
WARNING:
Always wear eye protection with side shields marked to comply with ANSI Z87.1. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury.
WARNING:
Do not use any attachments or accessories not recommended by the manufacturer of this tool. The use of attachments or accessories not recommended can result in serious personal injury.
WARNING:
Although many of the illustrations in this manual are shown with the blade guard removed for clarity, do not operate the saw without the blade guard unless specifically instructed to do so.
WARNING:
The table saw must be mounted to a firm supporting surface, such as a workbench or leg stand that positions the saw at waist height. Many illustrations in this manual are shown with the saw unmounted for clarity.
APPLICATIONS
You may use this tool for the purposes listed below: Straight line cutting operations such as cross cutting,
ripping, mitering, beveling, and compound cutting Dado or molding cuts with optional accessories Cabinet making and woodworking NOTE: This table saw is designed to cut wood and wood composition products only.
BASIC OPERATION OF THE TABLE SAW
To reduce the risk of electric shock, this tool has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. Refer to the Electrical section earlier in this manual.

CAUSES OF KICKBACK
Kickback can occur when the blade stalls or binds, kicking the workpiece back toward you with great force and speed. If your hands are near the saw blade, they may be jerked loose from the workpiece and may contact the blade. Obviously, kickback can cause serious injury, and it is well worth using precautions to avoid the risks.
Kickback can be caused by any action that pinches the blade in the wood, such as the following: Making a cut with incorrect blade depth Sawing into knots or nails in the workpiece Twisting the wood while making a cut Failing to support work Forcing a cut Cutting warped or wet lumber Using the wrong blade for the type of cut Not following correct operating procedures Misusing the saw Failing to use the anti-kickback pawls Cutting with a dull, gummed-up, or improperly set blade
AVOIDING KICKBACK
Always use the correct blade depth setting. The top of the blade teeth should clear the workpiece by 1/8 in. to 1/4 in.
Inspect the work for knots or nails before beginning a cut. Knock out any loose knots with a hammer. Never saw into a loose knot or nail.
Always use the rip fence when rip cutting. Use the miter gauge when cross cutting. This helps prevent twisting the wood in the cut.
Always use clean, sharp, and properly-set blades. Never make cuts with dull blades.
To avoid pinching the blade, support the work properly before beginning a cut.
When making a cut, use steady, even pressure. Never force cuts. Do not release the workpiece until you have pushed it completely past the blade.
Do not cut wet or warped lumber. The workpiece must have a straight edge for it to be guided along the rip fence.
Use extra caution when cutting some prefinished or composition wood products as the anti-kickback pawls may not always be effective.
Always guide your workpiece with both hands or with push sticks and/or push blocks. Keep your body in a balanced position to be ready to resist kickback should it occur. Never stand directly in line with the blade.
Use of a featherboard will help hold the workpiece securely against the saw table or fence.
Clean the saw, blade guard, under the throat plate, and any areas where sawdust or scrap workpieces may gather.

27 – English

OPERATION

Keep blade guard, riving knife and ainti-kickback pawls in place and proper operation. The riving knife must be in alignment with the blade and the pawls must stop a kickback once it has started. Check their operation before ripping.
Maintain the rip fence parallel with the saw blade. When ripping, apply the feed force to the section of the
workpiece between the blade and rip fence. Use a push stick and/or push block when appropriate. Use the right type of blade for the cut being made. Always use the riving knife for every operation where it is allowed. The use of this device will greatly reduce the risk of kickback.
CUTTING AIDS
See Figure 33 – 34.
Push sticks are devices that may be used for pushing a workpiece through the blade in any rip cut. When making non-through cuts or ripping narrow stock, always use a push stick, push block, and/or featherboard so your hands do not come within 3 inches of the saw blade. They can be made in various sizes and shapes from scrap wood and used in a specific project. The stick must be narrower than the workpiece, with a 90° notch in one end and shaped for gripping on the other end.
A push block has a handle fastened by recessed screws from the underside or secured with wood glue. Use push blocks for narrow cuts and all non-through cuts. A cutting jig or similar cutting aid may be necessary to ensure the push block does not interfere with the cut.
CAUTION:
Be sure the screws in a push block are recessed to avoid damaging the saw or workpiece.

To make a push block: The material, shape and size of a push block can vary. For this project, use two pieces of solid wood to make the base and handle. The base is 5 in. long, 3 in. wide. and 3/8 in. thick. The handle should be 5 in. long, 1 in. wide, and 3/4 in. thick. Mark the center of the base. Attach the handle to the center of the base using recessed
screws or wood glue. NOTE: To prevent the push block from slipping across the workpiece, you can attach a piece of sandpaper or a nonslip rubber pad to the bottom of the base.
PUSH STICKS

PUSH BLOCKS PUSH STICK

Fig. 33

Push blocks and push sticks like the ones shown in figure 33 can be purchased locally and a push stick is included with your saw. To make additional cutting aids, follow the instructions below.
To make a push stick:
The material, shape and size of a push stick can vary. For this project, use a piece of solid wood that is 18 in. long, 1-1/2 in. wide. and 3/4 in. thick. If desired, cut a curve into one end of the workpiece to
serve as a grip. Cut a notch into the workpiece on the opposite end.
During use, this end will contact the edge of the material being cut.

GRIP BASE

HANDLE

NOTCH PUSH BLOCK

Fig. 34

28 – English

OPERATION

WORKPIECE SUPPORTS
See Figure 35.
When cutting with your table saw, make sure that the workpiece you are cutting is properly supported. Properly supporting the workpiece throughout the cutting process not only improves the accuracy of the cut but also makes the cutting process safer for the user. This support could be required on the infeed side, the overhang side, or the outfeed side of the table. Improper support of the workpiece can cause the workpiece to move in unexpected ways during the process of the cut startling the user of the saw. It may also cause the user to apply abnormal forces to the workpiece to control it during the cutting process. This tipping motion of the workpiece will happen if approximately half of the workpiece overhangs any edge of the saw table.
Appropriate support can be easy to achieve. Commercially available support stands are available, or any surface that is the same height as the work surface of the saw would be acceptable. An operation that is practiced before actually making the cut will inform the user that supports may be necessary for safely completing the saw cut.
AUXILIARY FENCE
An auxiliary fence is a device used to close the gap between the rip fence and the saw table. Always make and use an auxiliary fence when ripping material 1/8 in. or thinner.
HOW TO MAKE AND ATTACH AN AUXILIARY FENCE (FOR RIP CUTTING THIN WORKPIECE)
See Figure 36.
An auxiliary fence may be made for the saw by cutting a piece of wood to 24 in. long, at least 3/4 in. thick, and at least 2-3/4 in. tall.
NOTE: The height and thickness of the auxiliary fence can be increased depending on the size and type of workpiece you are attempting to cut. Use taller auxiliary fences when cutting workpieces that are taller than the height of the rip fence.
To attach the auxiliary fence to the rip fence: Rotate the low fence so it will face away from the auxiliary
fence, refer to To Use the Rip Fence later in this section. Drill two countersunk holes as shown.

AUXILIARY T-BOLT FENCE

24 in.

NUT

3/4 in.

WASHER

STOP

2-3/4 in.

WORK SUPPORT
Fig. 35 RIP FENCE
Fig. 36 JIG HANDLE
JIG

WARNING:

Fig. 37

When mounting an auxiliary fence face, position mounting hardware beyond the arrows at right and left end of the rip fence warning label. Keep fasteners away from blade.

HOW TO MAKE A JIG (FOR RIP CUTTING
NARROW WORKPIECE)
See Figure 37.

Slide two T-bolts (not included) or 1/4-20 hex head bolts If ripping a narrow workpiece places the hands too close to (not included) into the rip fence groove beyond the arrows the blade, it will be necessary to make and use a jig.

at right and left of the label on the rip fence. Match the T-bolts to the holes in the auxiliary fence and
secure them to the rip fence with washers and nuts.

To make a jig: Attach a handle to a long, straight piece of wood and
secure from the underside using recessed screws.

Ensure that the auxiliary fence is securely attached and Cut an L-shaped stop in the side of the jig.

that the fasteners won’t interfere with the cutting operation

before use.

29 – English

OPERATION

To use a jig: Position the workpiece flat on the table with the edge
flush against the jig and against the stop. Holding the jig handle and using a push block and/or
push stick make the rip cut, see Making a Rip Cut later in this section.
FEATHERBOARD
A featherboard is a device used to help control the workpiece by holding it securely against the table or fence. Featherboards are especially useful when ripping small workpieces and for completing non-through cuts. The end is angled with a number of short kerfs to give a friction hold on the workpiece and locked in place on the table with a C-clamp. Test to ensure it can resist kickback.
WARNING:
Place the featherboard against the uncut portion of the workpiece to avoid kickback that could cause serious personal injury.

and cut spaced rips into the workpiece to allow approximately 1/4 in. fingers and 1/8 in. spaces between the fingers.
HOW TO MOUNT A FEATHERBOARD
See Figure 39.
Completely lower the saw blade. Position the rip fence to the desired adjustment for the cut to be performed and lock the rip fence. Place the workpiece against the fence and over the saw blade area. Adjust the featherboard to apply resistance to the workpiece just forward of the blade. Attach C-clamps to secure the featherboard to the edge of the saw table.
WARNING:
The featherboard must be installed in front of the blade. Do not locate the featherboard to the rear of the blade. Kickback can result from the featherboard pinching the workpiece and binding the blade in the saw kerf if positioned improperly. Failure to heed this warning can result in serious personal injury.

Commercially available featherboards can be purchased for a reasonable price. Many of these featherboards mount inside the miter slots of the saw and are convenient to mount and use on your table saw. To make a featherboard, follow the instructions in the next section.
HOW TO MAKE A FEATHERBOARD
See Figure 38.
The featherboard is an excellent project for the saw. Select a solid piece of lumber approximately 3/4 in. thick, 2-1/2 in. wide and 12 in. long. Mark the center of the width on one end of the stock. Miter the width to 70° (see page 39 for information on miter cuts). Mark the board from the widest point at four inches.
Prepare the saw for ripping as discussed on page 37. Set the rip fence to allow approximately a 1/4 in. “finger” to be cut in the stock. Feed the stock only to the mark previously made at 4 in. Turn the saw OFF and allow the blade to completely stop rotating before removing the stock. Reset the rip fence

FEATHERBOARD

C-CLAMP

PUSH STICK PUSH BLOCK
Fig. 39

2 1/2 in. 3/4 in.

1/4 in. 1/8 in.
12 in. 30 – English

70° 4 in.
Fig. 38

OPERATION

TYPES OF CUTS
See Figure 40.

There are six basic cuts: 1) the cross cut, 2) the rip cut, 3) the

1

miter cut, 4) the bevel cross cut, 5) the bevel rip cut, and 6) the

compound (bevel) miter cut. All other cuts are combinations

of these basic six. Operating procedures for making each

kind of cut are given later in this section.

CROSS CUT

WARNING:

Always make sure the blade guard and anti-

2

kickback pawls are in place and working properly

when making these cuts to avoid possible injury.

Cross cuts are straight 90° cuts made across the grain of

the workpiece. The wood is fed into the cut at a 90° angle

to the blade, and the blade is vertical.

Rip cuts are made with the grain of the wood. To avoid

3

kickback while making a rip cut, make sure one side of the

wood rides firmly against the rip fence.

Miter cuts are made with the wood at any angle to the blade other than 90°. The blade is vertical. Miter cuts tend to “creep” during cutting. This can be controlled by holding the workpiece securely against the miter gauge.
4

WARNING:

RIP CUT MITER CUT

Always use a push stick with small pieces of wood, and also to finish the cut when ripping a long narrow piece of wood, to prevent your hands from getting close to the blade.

BEVEL CROSS CUT

Bevel cuts are made with an angled blade. Bevel cross cuts

5

are across the wood grain, and bevel rip cuts are with the

grain. The rip fence must always be on the right side of the

blade for bevel rip cuts.

Compound (or bevel) miter cuts are made with an angled

blade on wood that is angled to the blade. Be thoroughly

familiar with making cross cuts, rip cuts, bevel cuts, and

miter cuts before trying a compound miter cut.

6

BEVEL RIP CUT

CUTTING TIPS
Dado and rabbet cuts are non-through cuts which can be either rip cuts or cross cuts. Carefully read and understand all sections of this operator’s manual before attempting any operation.
WARNING:
Do not use blades rated less than the speed of this tool. Failure to heed this warning could result in personal injury.
The kerf (the cut made by the blade in the wood) will be wider than the blade to avoid overheating or binding. Make allowance for the kerf when measuring wood.

COMPOUND (BEVEL) MITER CUT
Fig. 40
Make sure the kerf is made on the waste side of the measuring line.
Cut the wood with the finish side up. Knock out any loose knots with a hammer before making
the cut. Always provide proper support for the wood as it comes
out of the saw.

31 – English

OPERATION

TO CHANGE BLADE DEPTH
See Figure 41.
The blade depth should be set so that the outer points of the saw blade are higher than the workpiece by approximately 1/8 in. to 1/4 in. but the lowest points (gullets) are below the top surface. Unlock the blade height lock knob. Raise the saw blade by turning the height adjusting knob
clockwise or lower it by turning the knob counterclockwise. Once the desired saw blade height is achieved, lock the
blade height lock knob by turning it clockwise.
TO CHANGE BLADE ANGLE
See Figure 42.
NOTE: A 90° cut has a 0° bevel and a 45° cut has a 45° bevel. Unplug the saw. Unlock bevel locking lever by pulling the lever all the way
to the right. Adjust the bevel angle, turning the handwheel
counterclockwise increases the angle of the blade, bringing it closer to 45°. Turning it clockwise decreases the angle, bringing the blade closer to 90°.
NOTE: When the bevel adjusting handwheel is pushed back towards the saw housing and held in, the bevel angle can be quickly changed by pushing the handwheel left or right. Lock bevel locking lever by pushing lever to the left.
TO ADJUST THE BEVEL INDICATOR
See Figure 43.
If the bevel indicator is not at zero when the saw blade is at 90°, adjust the indicator by loosening the screws and setting at 0° on the bevel scale. Retighten the screws.

GULLET TO LOCK HEIGHT ADJUSTING KNOB

BEVEL LOCKING LEVER

Fig. 41 TO UNLOCK

BLADE HEIGHT LOCK KNOB

TO INCREASE
ANGLE

TO DECREASE
ANGLE
BEVEL ADJUSTING HANDWHEEL
Fig. 42

BEVEL LOCKING LEVER

BEVEL INDICATOR 32 – English

SCREW

Fig. 43

OPERATION

TO USE THE RIP FENCE
See Figures 44 – 45.

RIP FENCE

WARNING:
To reduce the risk of injury, always make sure the rip fence is parallel to the blade before beginning any operation.

LOW FENCE

NOTE: The rip fence included with your saw has an adjustable low fence that can be positioned to face towards or face away from the blade. The low fence should face away from the blade when cutting material greater than 3/4 inches thick. The low fence should only face the blade when cutting narrow material that is 3/4 inches thick or less. NEVER support the weight of the workpiece on the low fence while making a cut.
Loosen the rip fence by lifting the locking lever.
Place the front of the rip fence on the front rail.
Lower the back end of the rip fence onto the back rail.
Check for smooth gliding action.
Position the rip fence the desired distance from the blade.
With the rip fence flat on the saw table, push the fence towards the front rail to align the fence to the blade.
Push the locking lever down to align and secure the fence. When securely locked, the locking lever should point downward.
NOTE: Ensure the locking lever secures the rip fence in place. If adjustments are needed, see To Check The Tightness Of The Rip Fence Locking Lever in the Adjustment section of this manual.
NOTE: If the rip fence is not parallel to the blade, adjustments are needed. Refer to: To Check the Alignment of the Rip Fence to the Blade in the Adjustment section of this manual.

LOCKING LEVER

Fig. 44 BACK OF RIP FENCE
BACK RAIL
Fig. 45 INDICATOR

TO SET THE RIP FENCE SCALE INDICATOR TO THE BLADE
See Figure 46.
Use the indicator on the rip fence to position the fence along the scale on the front rail.
NOTE: The anti-kickback pawls and blade guard assembly must be removed to perform this adjustment. Reinstall the blade guard assembly when the adjustment is complete.
Begin with the blade at a zero angle (straight up). Unplug the saw. Place the rip fence on the saw table so that it lightly
touches the right side of the saw blade. Lock the rip fence in place.
NOTE: Position the low fence so that it faces away from the blade. Loosen screw and adjust the indicator so that it points to the “zero” line on the right rip scale on the front rail. Retighten screw.

SCREW
Fig. 46 NOTE: When using the low fence the rip fence scale indicator will be incorrect. Always use a tape measure to set the fence to the correct position when using the low fence.

33 – English

OPERATION

TO USE THE MITER GAUGE
See Figure 47.
The miter gauge provides greater accuracy in angled cuts. For very close tolerances, test cuts are recommended.
There are two miter gauge channels, one on either side of the blade. When making a 90° cross cut, you can use either miter gauge channel. When making a beveled cross cut (the blade tilted in relation to the table) the miter gauge should be located in the slot on the right so that the blade is tilted away from the miter gauge and your hands.
The miter gauge can be turned 60° to the right or left. Positive stops at 0° and 45° can be located by pushing in the stop pin. Slide the miter gauge in the miter gauge slot. Loosen the lock knob by turning it counterclockwise. Pull out the stop pin and rotate the gauge until the desired
angle is reached on the scale. Retighten the lock knob by turning it clockwise.
TO USE THE SLIDING TABLE EXTENSION
See Figure 48.
Increase the length of the saw table by using the sliding table extension. To provide sufficient material support when using the table extended, only set the fence beyond the arrow marked on the label on the rear rail.
NOTE: The low fence should face away from the blade when the table is extended. Remove the rip fence. Unlock the sliding table extension by lifting the table
extension lock lever. Slide the table extension to the desired width. Once the table extension is set to the desired width,
relock the lever by pushing the lever back towards the saw base.
ADJUSTING THE BLADE PARALLEL TO THE MITER GAUGE GROOVE (REMOVING HEEL)
See Figures 49 – 51.

MITER GAUGE

LOCK KNOB STOP PIN

POSITIVE STOPS

Fig. 47 SLIDING TABLE
EXTENSION

TO UNLOCK

TABLE EXTENSION LOCK LEVER

Fig. 48

BLADE TOOTH

MITER GAUGE GROOVE

WARNING:
The blade must be made parallel to the miter gauge groove so the wood does not bind resulting in kickback. Failure to do so could result in serious personal injury.

RULER Fig. 49

Do not loosen any screws for this adjustment until you have checked with a square and made test cuts to be sure adjustments are necessary. Once the screws are loosened, these items must be reset.
Unplug the saw.
Remove the blade guard, riving knife, and anti-kickback pawls. Raise the blade by turning the height adjusting handwheel clockwise.

NOTE: For details on removing and reinstalling the riving knife, see Cleaning the Riving Knife Lock Lever Plates in the Maintenance section of this manual.
Mark beside one of the blade teeth at the front of the blade. Using a ruler, measure the distance from the inside face of the blade tooth to the left edge of the right miter gauge groove.
NOTE: For greater accuracy, place the marked blade tooth on top of the ruler.

34 – English

OPERATION

Turn the blade so the marked tooth is at the back. Move the ruler to the rear and again measure the distance
from the inside face of the blade tooth to the left edge of the right miter gauge groove. If the distances are the same, the blade and the miter gauge groove are parallel. Replace blade guard, riving knife, and anti-kickback pawls.
If the distances are different: Remove the blade guard, riving knife, and anti-kickback
pawls. Raise the blade by turning the height adjusting handwheel. Loosen the outer screws 1/2 turn; this allows the mechanism beneath the table to be shifted sideways.
NOTE: The screws are located at the rear of the saw under the top of the saw table. Turn the alignment screw left or right until the blade is parallel to the miter gage groove. Tighten the outer screws. Check again for parallelism and continue to adjust if needed.
WARNING:
To reduce the risk of injury from kickback, align the rip fence to the blade following any blade adjustments. Always make sure the rip fence is parallel to the blade before beginning any operation.

RULER

OUTER SCREW

ALIGNMENT SCREW

MITER GAUGE GROOVE

OUTER SCREW

Fig. 50

MAKING CUTS

WARNING:
Before making any cuts, make sure that the table saw stand is on a firm level surface where there is plenty of room to handle and properly support the table saw and the workpiece. If a suitable location can not be found, then the saw should not be used. Operating the saw in a location that does not provide adequate space and stable footing for the table saw stand could create a tipping hazard which could result in serious personal injury.

This table saw can perform a variety of cuts that are not all mentioned in this manual. DO NOT attempt to make any cuts not covered here unless you are thoroughly familiar with the proper procedures and necessary accessories. Your local library has many books on table saw usage and specialized woodworking procedures for your reference.
The blade provided with the saw is a high-quality combination blade suitable for ripping and cross cut operations. Carefully check all setups and rotate the blade one full revolution to assure proper clearance before connecting saw to power source. Stand slightly to the side of the blade path to reduce the chance of injury should kickback occur.

Fig. 51
WARNING:
Do not use blades rated less than the speed of this tool. Failure to heed this warning could result in personal injury.
Use the miter gauge when making cross, miter, bevel, and compound miter cuts. To secure the angle, lock the miter gauge in place by twisting the lock knob clockwise. Always tighten the lock knob securely in place before use.

35 – English

OPERATION

During use the miter gauge may move slightly left or right inside the miter gauge groove. For greater accuracy, press the miter gauge against the left or right edge of the miter gauge groove when making cuts. Do not allow the gauge to go from one side to the other.
Always place the workpiece against the face of the miter gauge body when making cuts. To prevent the workpiece from moving, you can attach a piece of sandpaper to the miter gauge body face.
NOTE: It is recommended that you place the piece to be saved on the same side of the blade as the miter gauge, and that you make a test cut on scrap wood first.
MAKING A CROSS CUT
See Figures 52 – 54.

CROSS CUT

PLACE LEFT HAND ON WORKPIECE AND
MITER GAUGE HERE

PLACE RIGHT HAND ON MITER GAUGE
LOCK KNOB

WARNING:
Make sure the blade guard assembly is installed and working properly to avoid serious personal injury.

Fig. 52

WARNING:
Using the rip fence as a cutoff gauge when cross cutting will result in kickback which can cause serious personal injury.

Remove the rip fence by lifting the locking lever. Set the blade to the correct depth for the workpiece. Set the miter gauge to 0° and tighten the lock knob. Make sure the wood is clear of the blade before turning
on the saw. Press the top button on the switch to turn the saw on.
NOTE: The switch cover does not have to be raised to operate the switch. Press the bottom button on the switch to turn the saw off.
NOTE: To prevent unauthorized use, install a padlock (not included) through the holes in the switch and cover as shown in figure 53. Let the blade build up to full speed before moving the workpiece into the blade. Hold the workpiece firmly and feed the workpiece into the blade.
NOTE: The hand closest to the blade should be placed on the miter gauge lock knob and the hand farthest from the blade should be placed on the workpiece.

SWITCH ON

SWITCH OFF

SWITCH IN LOCKED POSITION

Fig. 53

When the cut is made, turn the saw off. Wait for the blade to come to a complete stop before removing any part of the workpiece.

36 – English

OPERATION

To make repetitive cross cuts:
A stop block can be used as a cut-off gauge to make repetitive cross cuts of the same length without having to mark the workpiece for each cut. The end of a stop block should always be in front of the blade. NEVER use the rip fence as a cut-off gauge. Remove the rip fence. Set the blade to the correct depth for the workpiece. Set the miter gauge to 0° and tighten the lock knob. Position a 3 in. block of wood at the desired distance
from the blade to act as a cut-off gauge. Secure the stop block in place using a vice or a clamp.

REPETITIVE CROSS CUT STOP BLOCK

WARNING:
When secured, the end of the stop block should be in front of the blade. Securing the stop block beyond the front of the blade will result in kickback which can cause serious personal injury.
Position the workpiece on the miter gauge with the edge flush against the stop block.
When cutting a long or wide workpiece, place a support the same height as the table surface in front of the saw, behind the saw, and on the sides of the saw as needed.
Turn the saw on. Hold the workpiece firmly with both hands on the miter
gauge and feed the workpiece into the blade. NOTE: The hand closest to the blade should be placed on the miter gauge lock knob and the hand farthest from the blade should be placed on the workpiece. When the cut is made, turn the saw off. Wait for the blade to come to a complete stop before removing the cut piece. Move the miter gauge back to the front of the saw and position the workpiece for the next cut. After the last cut, turn the saw off. Wait for the blade to come to a complete stop and remove the stop block.
MAKING A RIP CUT
See Figures 55 – 56.
WARNING:
Make sure the blade guard assembly is installed and working properly to avoid serious personal injury.
WARNING:
Taper cuts must only be made with a special jig, which is commercially available. Do not attempt a freehand taper cut on this saw. Failure to follow these instructions could result in serious personal injury.

BLADE

RIP CUT RIP FENCE

Fig. 54

PUSH BLOCK

PUSH STICK

Fig. 55
Set the blade to the correct depth for the workpiece. Move the low fence to the appropriate side of the rip
fence and install the rip fence.
NOTE: The low fence should only face the blade when cutting narrow material that is 3/4 inches thick or less. Wider workpieces and workpieces thicker than 3/4 inches may be unstable and require additional hold downs to ensure stability during cutting. Position the rip fence the desired distance from the blade for the cut and securely lock the handle. When cutting a long or wide workpiece, place a support the same height as the table surface in front of the saw, behind the saw, and on the sides of the saw as needed. Install featherboard in the appropriate position for the cut being made. Make sure the workpiece is clear of the blade before turning on the saw.

37 – English

OPERATION

Turn the saw on. Position the workpiece flat on the table with the edge
flush against the rip fence. Let the blade build up to full speed before feeding the workpiece into the blade. Using a push stick and/or push blocks, slowly feed the workpiece toward the blade. Stand slightly to the side of the workpiece as it contacts the blade to reduce the chance of injury should kickback occur. Once the blade has made contact with the workpiece, use the hand closest to the rip fence to guide it. Make sure the edge of the workpiece remains in solid contact with both the rip fence and the surface of the table. If ripping a narrow piece, use a push stick and/or push blocks to move the piece through the cut and past the blade. When the cut is made, turn the saw off. Wait for the blade to come to a complete stop before removing the workpiece.
To make rip cuts narrower than 2 inches:
If a narrow ripping jig is not used, the rip fence included with your saw has a low fence to allow narrow ripping operations.
NOTE: For cuts narrower than 2 inches, measure the distance from the blade to the fence using a tape measure. Do not use the rip scale when using the low fence.
WARNING:
When making narrow rip cuts always ensure that the piece being cut cannot fall into the throat plate of the saw. If this piece falls into the throat plate it may damage the under table guarding and create a hazardous condition to the operator.
Move the low fence so it faces the blade and install the rip fence.
NOTE: The rip fence included with your saw has an adjustable low fence that can be positioned to face towards or face away from the blade. The low fence should face away from the blade when cutting material greater than 3/4 inches thick. The low fence should only face the blade when cutting narrow material that is 3/4 inches thick or less. Lift the blade guard’s left or right side barrier and lower it onto either the workpiece or the narrow rip fence to ensure coverage of the cutting zone during this operation.

Secure the rip fence. Position the workpiece flat on the table with the edge
flush against the low fence. Using a push block and/or push stick make the rip cut,
see Making a Rip Cut earlier in this section.
NOTE: This technique is for making narrow rip cuts on workpieces with a thickness of 3/4 inches or less. To make narrow rip cuts on thicker material use a narrow ripping jig, refer to How To Make A Jig (For Rip Cutting Narrow Workpiece) earlier in this section.
NOTE: The cutting operation illustrated in figure 56 will result in the saved piece being between the rip fence and the right side of the blade. Alternatively, you could place the rip fence and the wide portion of the workpiece on the right side of the blade, which would result in the saved piece being on the left.
NARROW RIP CUT

BLADE

RIP FENCE LOW FENCE

PUSH STICK
Fig. 56

38 – English

OPERATION

MAKING A MITER CUT
See Figure 57.
WARNING:
Make sure the blade guard assembly is installed and working properly to avoid serious personal injury.
Set the blade to the correct depth for the workpiece. Remove the rip fence by lifting the locking lever. Set the miter gauge to desired angle and tighten the lock
knob. Make sure the workpiece is clear of the blade before
turning on the saw. Turn the saw on. Let the blade build up to full speed before moving the
workpiece into the blade. Hold the workpiece firmly with both hands and feed the
workpiece into the blade. NOTE: The hand closest to the blade should be placed on the miter gauge lock knob and the hand farthest from the blade should be placed on the workpiece. When the cut is made, turn the saw off. Wait for the blade to come to a complete stop before removing any part of the workpiece.
MAKING A BEVEL CROSS CUT
See Figures 58 – 59.
WARNING:
Make sure the blade guard assembly is installed and working properly to avoid serious personal injury.

Turn the saw on. Let the saw blade build up to full speed before moving
the miter gauge and the workpiece into the blade. Hold the workpiece firmly with both hands and feed the
workpiece into the blade.

NOTE: The hand closest to the blade should be placed on the miter gauge lock knob and the hand farthest from the blade should be placed on the workpiece. When the cut is made, turn the saw off. Wait for the blade to come to a complete stop before removing any part of the workpiece.

MITER CUT BLADE STRAIGHT

MITER GAUGE ANGLED

Fig. 57 VIEWED FROM THE FRONT, BELOW THE TABLE SAW
BEVEL LOCKING LEVER

WARNING:
The miter gauge must be on the right side of the blade to avoid trapping the wood and causing kickback. Placement of the miter gauge to the left of the blade will result in kickback and the risk of serious personal injury.

TO LOCK

Remove the rip fence by lifting the locking lever. Unlock the bevel locking lever. Turn the bevel adjusting handwheel until the bevel
indicator is at the desired angle. Push the bevel locking lever securely to the left to lock the angle. Push the bevel locking lever toward the table to relock. Set the blade to the correct depth for the workpiece. Set miter gauge to 0° and tighten the lock knob. Make sure the workpiece is clear of the blade before turning on the saw.

39 – English

TO UNLOCK

BEVEL CROSS CUT BLADE ANGLED

Fig. 58 MITER GAUGE
STRAIGHT

Fig. 59

OPERATION
MAKING A BEVEL RIP CUT
See Figure 60.
WARNING:
The rip fence must be on the right side of the blade to avoid trapping the wood and causing kickback. Placement of the rip fence to the left of the blade will result in kickback and the risk of serious personal injury.

BLADE ANGLED

BEVEL RIP CUT

RIP FENCE

WARNING:
Make sure the blade guard assembly is installed and working properly to avoid serious personal injury.

PUSH STICK

Remove the miter gauge. Install featherboard in the appropriate position for the cut
being made. Unlock the bevel locking lever. Adjust the bevel angle to the desired setting. Lock the bevel locking lever. Set the blade to the correct depth for the workpiece. Position the rip fence the desired distance from the blade
and securely lock down the lever. Make sure the wood is clear of the blade before turning
on the saw. When cutting a long or wide workpiece, place a support
the same height as the table surface in front of the saw, behind the saw, and on the sides of the saw as needed. Turn the saw on. Position the workpiece flat on the table with the edge flush against the rip fence. Let the blade build up to full speed before feeding the workpiece into the blade.

Fig. 60
Using a push stick and/or push blocks, slowly feed the workpiece toward the blade. Stand slightly to the side of the wood as it contacts the blade to reduce the chance of injury should kickback occur.
Once the blade has made contact with the workpiece, use the hand closest to the rip fence to guide it. Make sure the edge of the workpiece remains in solid contact with both the rip fence and the surface of the table. If ripping a narrow piece, use a push stick to move the piece through the cut and past the blade.
When the cut is made, turn the saw off. Wait for the blade to come to a complete stop before removing any part of the workpiece.

40 – English

OPERATION
MAKING A COMPOUND (BEVEL) MITER CUT
See Figure 61.
WARNING:
Make sure the blade guard assembly is installed and working properly to avoid serious personal injury.

COMPOUND (BEVEL) MITER CUT PLACE RIGHT HAND ON WORKPIECE HERE

WARNING:
The miter gauge must be on the right side of the blade to avoid trapping the wood and causing kickback. Placement of the miter gauge to the left of the blade will result in kickback and the risk of serious personal injury.
Remove the rip fence by lifting the locking lever. Unlock the bevel locking lever. Adjust the bevel angle to the desired setting. Lock the bevel locking lever. Set the blade to the correct depth for the workpiece. Set the miter gauge to the desired angle and tighten the
lock knob. Make sure the wood is clear of the blade before turning
on the saw. Turn the saw on.

Fig. 61
Let the blade build up to full speed before moving the workpiece into the blade.
Hold the workpiece firmly with both hands on the miter gauge and feed the workpiece into the blade. NOTE: The hand closest to the blade should be placed on the miter gauge lock knob and the hand farthest from the blade should be placed on the workpiece.
When the cut is made, turn the saw off. Wait for the blade to come to a complete stop before removing the workpiece.

41 – English

OPERATION

MAKING A LARGE PANEL CUT
See Figure 62. Make sure the saw is properly secured to a work surface or leg stand to avoid tipping from the weight of a large panel.
WARNING:
Make sure the blade guard assembly is installed and working properly to avoid serious personal injury.

SUPPORT

LARGE PANEL CUT RIP
FENCE

WARNING:
Never make freehand cuts (cuts without the miter gauge or rip fence). Such a cut increases the risk of kickback and can result in serious injury.
Install featherboard in the appropriate position for the cut being made.
When cutting a long or wide workpiece, place a support the same height as the table surface in front of the saw, behind the saw, and on the sides of the saw as needed.

BEVEL ADJUSTING HANDWHEEL

WARNING:
Improper support of the workpiece on the side and/or outfeed side of the saw could create unexpected movement of the workpiece and/ or the saw, resulting in serious personal injury.
Depending on the shape of the panel, use the rip fence or miter gauge. If the panel is too large to use either the rip fence or the miter gauge, it is too large for this saw.
Make sure the workpiece does not touch the blade before you turn on the saw.
Turn the saw on. Position the workpiece flat on the table with the edge
flush against the rip fence. Let the blade build up to full speed before feeding the workpiece into the blade.

Fig. 62
Using a push stick and/or push blocks, slowly feed the workpiece toward the blade. Stand slightly to the side of the wood as it contacts the blade to reduce the chance of injury should kickback occur.
Once the blade has made contact with the workpiece, use the hand closest to the rip fence to guide it. Make sure the edge of the workpiece remains in solid contact with both the rip fence and the surface of the table. If ripping a narrow piece, use a push stick to move the piece through the cut and past the blade.
When the cut is made, turn the saw off. Wait for the blade to come to a complete stop before removing the workpiece.

42 – English

OPERATION
MAKING A NON-THROUGH CUT
See Figure 63. Non-through cuts (made with a standard 10 in. blade) can be made with the grain (ripping) or across the grain (cross cut). The use of a non-through cut is essential to cutting grooves, rabbets, and dadoes. This is the only type cut that is made without the blade guard assembly installed. Make sure the blade guard assembly is reinstalled upon completion of this type of cut. Read the appropriate section which describes the type of cut in addition to this section on non-through or dado cuts. For example, if your non-through cut is a straight cross cut, read and understand the section on straight cross cuts before proceeding.
WARNING:
When making a non-through cut, the blade is covered by the workpiece during most of the cut. Be alert to the exposed blade at the start and finish of every cut to reduce the risk of personal injury.

NON-THROUGH CUT BLADE GUARD REMOVED
PUSH BLOCK

WARNING:
Never feed wood with your hands when making any non-through cut such as rabbets or dadoes. To avoid personal injury, always use push blocks, push sticks, and featherboards.
Unplug the saw. Remove the blade guard and anti-kickback pawls. Place riving knife in “down” position. Unlock the bevel locking lever. Turn the bevel adjusting handwheel until the bevel
indicator is at the desired angle. Push the bevel locking lever securely to the left to lock the angle. Set the blade to the correct depth for the workpiece. Plug the saw into the power source and turn on saw. Let the blade build up to full speed before moving the workpiece into the blade.

Fig. 63
Always use push blocks, push sticks, and/or featherboards appropriately when making non-through cuts to reduce the risk of serious injury.
When the cut is made, turn the saw off. Wait for the blade to come to a complete stop before removing the workpiece.
NOTE: A non-through rip cut is shown in the illustration above. To make a non- through cross cut, remove the blade guard and anti-kickback pawls. Place the riving knife in the “down” position and perform the cross cut, see Making a Cross Cut earlier in this section.
Once all non-through cuts are completed: Unplug your saw. Place riving knife in “up” position. Reinstall blade guard and anti-kickback pawls.

43 – English

OPERATION

MAKING A DADO CUT
See Figure 64.
An optional dado throat plate is required for this procedure (see to the Accessories section later in this manual and check with the retailer where the table saw was purchased). All blades and dado sets must not be rated less than the speed of this tool. This saw is designed for use with a 6 in. stack dado (up to width of 3/4 in.). Do not use an adjustable dado on this saw.

BLADE GUARD REMOVED

DADO CUT

MITER GAUGE

NOTE: This saw cannot be used to make a bevel dado cut.

Rabbeting cuts are dado cuts made on the end of a workpiece. For best results, complete rabbet cuts using a dado stack blade.

NOTE: Use an auxiliary fence when making rabbet cuts to prevent the face of the rip frence from making contact with the dado blade stack during the cutting operation.

Fig. 64

WARNING:

Make sure the blade nut is fully engaged and the arbor extends past a securely tightened blade nut.

When making a non-through cut, the blade is covered by the workpiece during most of the cut. Be alert to the exposed blade at the start and finish of every cut to reduce the risk of personal injury.

Place riving knife release lever in locked position. Install the dado throat plate and rotate the blade by hand
to make sure it turns freely then lower the blade. Set the blade height. Depending on the shape and size of the wood, use either
the rip fence or miter gauge.

WARNING:
Always put all blade washers in proper location when reinstalling standard blade. Failure to do so can result in possible injury and damage to the tool.

If making a rip cut, install featherboard in the appropriate position for the cut being made.
Plug in saw then turn the saw on.
NOTE: Make sure the wood does not touch the blade before you turn on the saw. Let the blade build up to full speed before feeding the workpiece into the blade.

WARNING:
Always use push blocks, push sticks, and/or featherboards when making dado cuts to avoid the risk of serious injury.
Unplug your saw. Remove the blade guard, anti-kickback pawls, throat
plate, and riving knife.
NOTE: For details on removing and reinstalling the riving knife, see Cleaning the Riving Knife Lock Lever Plates in the Maintenance section of this manual. Remove the blade nut, blade washer, and saw blade. NOTE: Always store the blade washer and throat plate in a secure location. Mount the dado blade, according to manufacturer instructions, using the blade and chippers appropriate for the desired width of cut.

Position the workpiece flat on the table with the edge flush against the rip fence or miter gauge and hold firmly against the saw table.
Use a push block or push stick to move the wood through the cut past the blade. Never push a small piece of wood into the blade with your hand, always use a push stick. The use of push blocks, push sticks, and featherboards are necessary when making non-through cuts.
When the cut is made, turn the saw off. Wait for the blade to come to a complete stop before removing the workpiece.
NOTE: A dado cross cut is shown in the illustration above. To make a dado rip cut, remove the blade guard, anti-kickback pawls, throat plate, and riving knife. Install the dado blade and dado throat plate then perform the rip cut, see Making a Rip Cut earlier in this section.
Once all dado cuts are completed: Unplug your saw.
Remove the dado throat plate and dado blade.

Reinstall and securely tighten the blade nut.

Reinstall the riving knife in the “up” position.

NOTE: The blade washer may be used provided the arbor Reinstall standard cutting blade, throat plate, blade guard

shaft extends slightly beyond the arbor nut.

and anti-kickback pawls.

44 – English

ADJUSTMENTS

WARNING:
Before performing any adjustment, make sure the tool is unplugged from the power supply and the top button on the switch is not depressed. Failure to heed this warning could result in serious personal injury.

BLADE WRENCH
(LEFT)

BLADE WRENCH (RIGHT)

To avoid unnecessary set-ups and adjustments, a good practice is to check your setups carefully with a framing square and make practice cuts in scrap wood before making finish cuts in good workpieces. Do not start any adjustments until you have checked with a square and made test cuts to be sure adjustments are needed.
TO REPLACE THE BLADE
See Figures 65 – 66.
Wear gloves and other personal protective equipment when installing and removing a blade only. DO NOT wear gloves when operating the saw. DO NOT place gloved hand near blade when it is in motion.
Use correct blades. Blade kerf width and blade body thickness must be within the limits stamped on the riving knife. Unplug the saw. Remove the blade guard and anti-kickback pawls. Lower the saw blade and remove the throat plate. Lock the bevel locking lever. Raise the saw blade to full height. Using the left blade wrench, insert the open end onto the
flats on the arbor shaft. Insert the closed end of the other wrench over the hex
nut. Holding both wrenches firmly, pull the outside wrench (right side) forward while pushing the inside (left side) to the back of the saw. Remove the hex nut and blade washer.
NOTE: Arbor shaft has right-hand threads. Unlock the release lever to remove the blade.
To replace the blade with an accessory blade, follow the instructions provided with the accessory.
To install a standard blade: Place the new blade on the arbor shaft (the teeth must
point down toward the front of the saw to work properly). Place the blade washer and the hex nut over the arbor
shaft. Be sure the domed side of the blade washer faces out from the blade and that all items are snug against the arbor flange. Make sure the hex nut is securely tightened. Do not overtighten.
NOTE: Arbor shaft has right-hand threads.

HEX NUT ARBOR SHAFT

RELEASE LEVER

BLADE

Fig. 65
BLADE WASHER
HEX NUT

Fig. 66
Lock the release lever. Rotate the blade by hand to make sure it turns freely. Lower the saw blade and reinstall the throat plate. Check all clearances for free blade rotation. After installation, adjust the rip scale indicator to account for the kerf and thickness of the blade. Refer to To Set the Rip Fence Scale Indicator to the Blade in the Operation section of this manual. In cutting operations, the scale will be set to the side of the blade where the cut will be measured and made.

45 – English

ADJUSTMENTS

TO SET THE BEVEL INDICATOR AND BEVEL STOPS AT 0° AND 45° See Figures 67 – 68.
The angle settings of the saw have been set at the factory and, unless damaged in shipping, should not require setting during assembly. After extensive use, it may need to be checked. Unplug the saw. Raise the blade. Remove the blade guard and anti-kickback pawls. To check for squareness, 0° bevel: Release the bevel locking lever. Rotate the bevel adjusting handwheel until the blade is
tilted to the right as far as it will go. Lock the bevel locking lever. Place the combination square against blade. Make sure
square is not touching the tip of one of the saw teeth.
If the blade is not an exact 90° (0° bevel): Release the bevel locking lever. Rotate the bevel adjusting handwheel until the bevel
indicator points to 5°-10°. Turn the 0° stop screw 1/4 turn in the clockwise or
counterclockwise direction. Rotate the bevel adjusting handwheel until the blade is
tilted to the right as far as it will go. Lock the bevel locking lever and check the blade angle. Repeat above steps to readjust and recheck blade angle
as needed.
Once blade is square to the table (0° bevel): Check bevel indicator. If indicator is not pointing to the 0º mark on the bevel
scale, loosen the indicator adjusting screw and adjust indicator. Retighten screw. To check for squareness, 45° bevel: Release the bevel locking lever. Rotate the bevel adjusting handwheel until the blade is tilted to the left as far as it will go. Lock the bevel locking lever. Place the combination square against blade. Make sure square is not touching the tip of one of the saw teeth.
If the blade is not an exact 45°: Release the bevel locking lever. Rotate the bevel adjusting handwheel until the bevel
indicator points to 35°-40°. Turn the 45° stop screw 1/4 turn in the clockwise or
counterclockwise direction.

BLADE AT 0° BEVEL

BEVEL LOCKING LEVER

0° STOP SCREW

INDICATOR ADJUSTING SCREW

BEVEL ADJUSTING HANDWHEEL
Fig. 67

BLADE AT 45° BEVEL

45° STOP SCREW

BEVEL ADJUSTING HANDWHEEL

BEVEL LOCKING LEVER

INDICATOR ADJUSTING SCREW
Fig. 68

Rotate the bevel adjusting handwheel until the blade is tilted to the left as far as it will go.
Lock the bevel locking lever and check the blade angle. Repeat above steps to readjust and recheck blade angle
as needed.

46 – English

ADJUSTMENTS

Once blade is 45° to the table: Check bevel indicator. If indicator is not pointing to the 45º mark on the bevel
scale, loosen the indicator adjusting screw and adjust indicator. Retighten screws.
When all adjustments are complete: Reinstall blade guard and anti-kickback pawls.
TO ADJUST THE MITER GAUGE See Figure 69.
You can set the miter gauge at 0º and plus or minus 45º with the miter gauge stop pin and adjustable stop screws.
NOTE: The miter gauge provides close accuracy in angled cuts. For very close tolerances, test cuts are recommended.
To adjust stop screws: Loosen the lock knob and pull out on stop pin to rotate
miter gauge base past stop screws. Loosen the lock nut of the 0º stop screw at the stop pin
with a wrench. Place a 90º square against the miter gauge rod and the
miter gauge base. If the rod is not square, loosen the lock knob, adjust the
rod, and retighten the knob. Adjust the stop screw until it rests against the stop pin
and tighten lock nut.
TO CHECK THE ALIGNMENT OF THE RIP FENCE TO THE BLADE See Figures 70 – 73.
The rip fence must be parallel to the saw blade and the miter gauge grooves.

MITER GAUGE ROD

0° ADJUSTABLE STOP SCREW

LOCK KNOB

MITER GAUGE BASE
45° ADJUSTABLE STOP SCREW

LOCK NUT

STOP PIN Fig. 69

BLADE TOOTH

BLADE RIP FENCE

WARNING:
A misaligned rip fence can cause kickbacks and jams. To reduce the risk of injury, always maintain proper rip fence alignment.
Unplug the saw. Remove the blade guard, riving knife, and anti-kickback
pawls. Raise the blade by turning the height adjusting handwheel clockwise. Verify the blade is parallel to the miter gauge groove as described in the Adjusting the Blade Parallel to the Miter Gauge Groove (Removing Heel) section in Operations. Move the low fence so it faces away from the blade and install the rip fence. Move the rip fence near the saw blade (about three inches away) and lock the rip fence in place with the locking lever.

Fig. 70
Mark beside one of the blade teeth at the front of the blade. Using a ruler, measure the distance from the inside face of the blade tooth to the inside face of the rip fence.
NOTE: For greater accuracy, place the marked blade tooth on top of the ruler. Turn the blade so the marked tooth is at the back. Move the ruler to the rear and again measure the distance from the inside face of the blade tooth to the inside face of the rip fence. If the distances are the same, the blade and the rip fence are parallel.

47 – English

ADJUSTMENTS

If the distances are different: Remove the rip fence. Loosen but do not remove the two hex head cap screws
located on top of the rip fence, the Phillips screw above the locking lever, and the two hex head cap screws on the bottom of the rip fence. Install the fence and recheck alignment. Adjust the rip fence. Tighten the hex head cap screws on top of the rip fence and the Phillips screw above the locking lever. Recheck alignment. Remove the fence and tighten the two hex head cap screws on the bottom of the fence. Install the fence, lock it in place, and recheck alignment. Repeat steps as needed until rip fence is correctly aligned. Replace blade guard, riving knife, and anti-kickback pawls. Make two or three test cuts on scrap wood. If the cuts are not true, repeat the process.
To check the alignment of the low fence: Unplug the saw. Verify the blade is parallel to the miter gauge groove as
described in the Adjusting the Blade Parallel to the Miter Gauge Groove (Removing Heel) section in Operations. Verify that the rip fence is parallel to the saw blade as described earlier in this section. Remove the rip fence. Turn the rip fence on its side with the indicator facing up. Place the fence on a flat level surface with the front of the fence hanging over the edge. Place a combination square against the rip fence and low fence as shown. Measure the distance from the side of the rip fence to the exterior edge of the low fence. Move the combination square and measure the distance at the opposite end of the low fence.
NOTE: If the distances are the same, swing the low fence to the other side of the rip fence, turn the rip fence over so that the indicator faces down, and recheck alignment.
If the distances are different: Loosen but do not remove the Phillips screws at the
front and back of the low fence.
NOTE: After the screws are loosened, the position of the low fence can be adjusted by hand. Tighten Phillips screws. Recheck alignment. Repeat steps as needed until low fence is correctly aligned. Replace blade guard, riving knife, and anti-kickback pawls. Make two or three test cuts on scrap wood. If the cuts are not true, repeat the process.

HEX HEAD CAP SCREWS
PHILLIPS SCREW HEX HEAD CAP SCREWS
LOCKING LEVER

FRONT OF RIP FENCE
INDICATOR

LOW FENCE

Fig. 71 COMBINATION
SQUARE

RIP FENCE LOW FENCE

Fig. 72 SCREWS

RIP FENCE

Fig. 73

48 – English

ADJUSTMENTS

TO CHECK THE TIGHTNESS OF THE RIP FENCE LOCKING LEVER See Figure 74.
The locking lever on the rip fence should hold the rip fence securely against the front and back rails. The lever should not be difficult to push down and lock. To assure proper fence lock adjustment: Lock the rip fence in place. Try moving the fence from side-to-side. If the fence moves,
tighten the adjusting nut 1/4 turn. With the rip fence in the locked position, recheck rip fence
parallelism with the blade and adjust if necessary.
TO ADJUST THE BEVEL LOCKING LEVER See Figure 75. Release bevel locking lever and bevel saw blade to 45º. Push bevel locking lever to lock blade into place. With moderate force, attempt to move the bevel adjusting
handwheel toward the 0º bevel. If bevel adjusting handwheel cannot be moved, no
adjustment is needed. If handwheel can be moved, adjust the bevel lock nut by rotating clockwise 1/4 turn. Repeat above step as necessary. Release bevel locking lever and move bevel adjusting handwheel back to 0º.

ADJUSTING NUT
BEVEL LOCK NUT

Fig. 74 Fig. 75

49 – English

ADJUSTMENTS

CHECKING THE TABLE EXTENSION See Figure 76.
Lock the sliding table extension. The sliding table extension should not move while locked. If the extension moves: Lift the table extension lock lever. Find the hex coupling located underneath the saw table. Loosen the hex locking nuts. Turn the hex coupling counterclockwise. Lock the table extension lock. Push and pull on the sliding
table extension. Readjust hex coupling if necessary. Tighten the hex locking nuts against coupling.

TO ADJUST THE HEIGHT OF THE TABLE EXTENSION See Figure 77.
Lock table extension lever.
Loosen the four nuts underneath the sliding table extension.
Use a square to make sure the top of the sliding table extension is the same height as the main table.
Tighten the four hex nuts. Recheck and readjust if necessary.

HEX COUPLING

HEX LOCKING NUTS

SQUARE

HEX NUT TABLE
EXTENSION

Fig. 76
MAINTENANCE
WARNING:
When servicing, use only identical replacement parts. Use of any other parts could create a hazard or cause product damage.

Fig. 77
WARNING:
Always wear eye protection with side shields marked to comply with ANSI Z87.1 during product operation. If operation is dusty, also wear a dust mask.

50 – English

MAINTENANCE

WARNING:
Before performing any maintenance, make sure the tool is unplugged from the power supply and the top button on the switch is not depressed. Failure to heed this warning could result in serious personal injury.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.
WARNING:
Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which could result in serious personal injury.
Periodically check all clamps, nuts, bolts, and screws for tightness and condition. Make sure the throat plate is in good condition and in position.
Check the blade guard assembly for proper installation, fit, clearances, and for free movement. Some wood types may cause a buildup of dust, pitch, or resin on components, so regular maintenance and cleaning is recommended. Any cleaner used must be appropriate for use on plastic parts.
Clean plastic parts only with a soft damp cloth. Do not use any aerosol or petroleum solvents.
Protect the blade by cleaning out sawdust from underneath the table and in the blade teeth. Clean blade teeth with a solvent recommended for gum and pitch removal.
To maintain the table surfaces, fence, and rails, periodically apply paste wax to them and buff to provide smooth functioning. To prevent work from slipping during cutting operation, do not wax the working face of the miter gauge.
LUBRICATION
This saw’s motor bearings have been packed at the factory with proper lubrication. Clean screw threads and nuts with a solvent
recommended for gum and pitch removal. Lubricate screw threads, nuts, and bearing points
(including those on the blade guard assembly and miter gauge).

CLEANING THE RIVING KNIFE LOCK LEVER PLATES
See Figure 78. The lock lever on the riving knife may become difficult to lock securely after extended use due to sawdust or debris falling into the plates. Unplug the saw. Unlock the lever to remove the riving knife. Wipe the area with a clean dry cloth or use compressed
air to blow away debris. Clean the riving knife. Reinstall the riving knife and turn the lever to lock the
riving knife in place. NOTE: If the lock lever is difficult to move or will not fully close after the plates have been cleaned, contact customer service.
WARNING:
Do not use the saw if the lock lever does not fully close. Doing so may cause serious personal injury.
RIVING KNIFE

PLATES

LOCK LEVER

Fig. 78

51 – English

MAINTENANCE

CLEANING DUST CHUTE
See Figure 79.
This saw features a dust chute for convenience in discharging sawdust. A standard shop vac can be attached to the chute, located under the back side of the saw.
During periods of extended use, the dust chute should be emptied and cleaned to prevent buildup of sawdust and to make sure there are no obstructions or other small offcuts that may have fallen into the throat plate opening that could hinder maximum performance.

To remove/clean the dust chute: Unplug your saw. Loosen wing screws. Lift the dust chute slightly and move it away from the
blade. Clean sawdust and wood chips from the dust chute. To reinstall dust chute: Tilt dust chute and slide the tab under the slot (A). Hook the right side of the dust chute under the screw (B). Secure in place using wing screws (C).

(B) HOOK

(A)

SLOT

TAB

SCREW (C)

DUST CHUTE
WING SCREW

Fig. 79

52 – English

MAINTENANCE

BRUSH REPLACEMENT
See Figure 80. Unplug the saw. Lower blade completely and bevel to 45º. Lock the blade. Turn saw upside down. Remove brush caps with a screwdriver.
NOTE: Brush assembly is spring load and will pop out when brush cap is removed. Remove brush assemblies and check for wear. Replace both brushes when either has less than 1/4 in. length of carbon remaining. Do not replace one side without replacing the other. Reassemble using new brush assemblies by reversing the steps listed above. Make sure curvature of brush matches curvature of motor and that brush moves freely in brush tube. Tighten all brush caps securely. Do not overtighten.

BRUSH CAP

BRUSH ASSEMBLY

BRUSH CAP Fig. 80

ACCESSORIES

Look for these accessories where you purchased this product or call 1-866-539-1710: Dado Throat Plate ……………………………………………………………………………………………………………………….089240028701 Flip Top Portable Work Support………………………………………………………………………………………………………………AC9934

WARNING:
Current attachments and accessories available for use with this product are listed above. Do not use any attachments or accessories not recommended by the manufacturer of this product. The use of attachments or accessories not recommended can result in serious personal injury.

TROUBLESHOOTING

Problem
Excess vibration.
Rip fence does not move smoothly. Rip fence does not lock at rear.

Cause
Blade is out of balance. Blade is damaged. Saw is not mounted securely. Work surface is uneven. Blade is warped.
Rip fence not mounted correctly. Rails are dirty or sticky. Adjusting nut is out of adjustment.
Adjusting nut is out of adjustment.

Solution
Replace blade. Replace blade. Tighten all hardware. Reposition on flat surface. Check saw blade installation.
Remount the rip fence. Clean rails. Adjust adjusting nut.
Adjust adjusting nut.

53 – English

TROUBLESHOOTING

Problem

Cause

Solution

Cutting binds or burns work.

Blade is dull. Blade is heeling.

Work is fed too fast. Rip fence is misaligned. Riving knife is out of alignment.

Workpiece is warped.

Workpiece edges away from rip fence Rip fence is misaligned.

when ripping.

Blade not properly aligned or set.

Replace or sharpen blade.
See Adjusting the Blade Parallel to the Miter Gauge Groove (Removing Heel) in the Operation section.
Slow the feed rate.
Align the rip fence.
See To Check and Align the Riving Knife and Saw Blade in the Assembly section.
Replace the workpiece. Always cut with convex side to table surface.
Check and adjust the rip fence.
Resharpen or set blade.

Saw does not make 0° or 45° cuts. Height Adjusting Knob is hard to turn. Saw does not start.
Blade makes poor cuts. Motor overheats.

Bevel stops not properly adjusted.

See To Set the Bevel Indicator and Bevel Stops at 0° and 45° (Squaring
the Blade) in the Adjustments section.

Miter gauge is misaligned (Miter Cuts). See To Adjust the Miter Gauge in the Adjustments section.

Gears or screw post behind the front Clean the gears or screw posts. panel are clogged with sawdust.

Handwheel is locked.

Unlock the blade height lock knob by pushing the bevel lock lever to the right.

Power cord not plugged in.

Plug in power cord.

Circuit fuse is blown.

Replace circuit fuse.

Circuit breaker is tripped.

Reset circuit breaker.

Cord, switch, or motor is damaged.

Have replaced by qualified service center.

Blade is dull or dirty.

Clean, sharpen, or replace blade.

Blade is wrong type for cut being made. Replace with correct type.

Blade is mounted backwards.

Remount blade.

Work is fed too fast; motor overloaded. Feed work slower into the blade.

Motor labors in rip cut.

Blade not proper for rip cut.

Change blade; rip blade typically has fewer teeth.

Blade coasts for longer than a few Electric brake may not be working Contact customer service. seconds after the saw is turned off. properly.

54 – English

WARRANTY

RIDGID® HAND HELD AND STATIONARY POWER TOOL 3 YEAR LIMITED SERVICE WARRANTY

Proof of purchase must be presented when requesting warranty service.
Limited to RIDGID® hand held and stationary power tools purchased 2/1/04 and after. This product is manufactured by One World Technologies, Inc. The trademark is licensed from RIDGID, Inc. All warranty communications should be directed to One World Technologies, Inc., attn: RIDGID Hand Held and Stationary Power Tool Technical Service at (toll free) 1-866-539-1710.
90-DAY SATISFACTION GUARANTEE POLICY
During the first 90 days after the date of purchase, if you are dissatisfied with the performance of this RIDGID® Hand Held or Stationary Power Tool for any reason you may return the tool to the dealer from which it was purchased for a full refund or exchange. To receive a replacement tool you must present proof of purchase and return all original equipment packaged with the original product. The replacement tool will be covered by the limited warranty for the balance of the 3 YEAR service warranty period.
WHAT IS COVERED UNDER THE 3 YEAR
LIMITED SERVICE WARRANTY
This warranty on RIDGID® Hand Held and Stationary Power Tools covers all defects in workmanship or materials and normal wear items such as brushes, chucks, motors, switches, cords, gears and even cordless batteries in this RIDGID® tool for three years following the purchase date of the tool. Warranties for other RIDGID® products may vary.
HOW TO OBTAIN SERVICE
To obtain service for this RIDGID® tool you must return it; freight prepaid, or take it in to an authorized service center for RIDGID® branded hand held and stationary power tools. You may obtain the location of the authorized service center nearest you by calling (toll free) 1-866-539-1710 or by logging on to the RIDGID® website at www.ridgid.com. When requesting warranty service, you must present the original dated sales receipt. The authorized service center will repair any faulty workmanship, and either repair or replace any part covered under the warranty, at our option, at no charge to you.

WHAT IS NOT COVERED
This warranty applies only to the original purchaser at retail and may not be transferred. This warranty only covers defects arising under normal usage and does not cover any malfunction, failure or defect resulting from misuse, abuse, neglect, alteration, modification or repair by other than an authorized service center for RIDGID® branded hand held and stationary power tools. Consumable accessories provided with the tool such as, but not limited to, blades, bits and sand paper are not covered.
RIDGID, INC. AND ONE WORLD TECHNOLOGIES, INC. MAKE NO WARRANTIES, REPRESENTATIONS OR PROMISES AS TO THE QUALITY OR PERFORMANCE OF ITS POWER TOOLS OTHER THAN THOSE SPECIFICALLY STATED IN THIS WARRANTY.
ADDITIONAL LIMITATIONS
To the extent permitted by applicable law, all implied warranties, including warranties of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, are disclaimed. Any implied warranties, including warranties of merchantability or fitness for a particular purpose, that cannot be disclaimed under state law are limited to three years from the date of purchase. One World Technologies, Inc. and RIDGID, Inc. are not responsible for direct, indirect, incidental or consequential damages. Some states do not allow limitations on how long an implied warranty lasts and/or do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
One World Technologies, Inc.
P.O. Box 1427
Anderson, SC 29622

55 – English

RÈGLES DE SÉCURITÉ GÉNÉRALES

AVERTISSEMENT :
Lire les avertissements de sécurité, les instructions et les précisions et consulter les illustrations fournis avec cet outil électrique. Le fait de ne pas se conformer à l’ensemble des consignes présentées cidessous risque d’entraîner des décharges électriques, un incendie et/ou des blessures graves.

SÉCURITÉ PERSONNELLE
Rester attentif, prêter attention au travail et faire preuve de bon sens lors de l’utilisation de tout outil électrique. Ne pas utiliser cet outil en état de fatigue ou sous l’influence de l’alcool, de drogues ou de médicaments. Un moment d’inattention pendant l’utilisation d’un outil électrique peut entraîner des blessures graves.
Utiliser l’équipement de sécurité. Toujours porter une

protection oculaire. L’équipement de sécurité, tel qu’un

Conserver les avertiss

References

• register.RIDGID.com
• Rugged Jobsite Tools | RIDGID Tools

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>