Arris / Surfboard SBG6950
- June 7, 2024
- Arris
Table of Contents
Details
| |
---|---|---
Modem Information
DOCSIS 3.0 Dual Band 802.11-AC WiFi Modem
16×4 channel bonding
To achieve Gigablast or Ultimate speeds, a DOCSIS 3.1 modem is required
|
Highest Service Level
Preferred 150
|
---|---
Front View
| | After the cable modem is successfully registered on the network, the
Power, Send/Receive, and Online indicators illuminate continuously to indicate
that the cable modem is online and fully operational.
| |
Back View
| | The following ports are available on the back of the modem.
- Reset – Use this button to reboot the modem or restore to factory defaults. It is recessed to prevent accidental resets. To reboot the modem, press and hold the Reset button for three to four seconds. To restore factory defaults, press and hold the Reset button for more than 10 seconds.
- Ethernet (1 – 4) – Connects to the 10/100/1000 Ethernet ports on your computer. Provides internet access to a single device. Only one port is active at a time.
- Cable – Connects to the cable wall outlet.
- Power – Connects the modem to the power cord.
| |
MAC Address / WiFi Network Label
| | This label is located on the bottom of the device.
- MAC addresses are written as 12 digits containing both letters and numbers (0-9, A-F).
- A MAC address is unique.
- The first six characters of the MAC address are unique to the manufacturer of the device.
- The default Network Name (SSID) and Passphrase (Preshared Key).
Troubleshooting
The lights indicate the current status of your modem. To troubleshoot any connection problems, use the table below.
| Modem Light | Status | Problem |
|---|
Power
| Off| No Power. Verify all cable connections and try resetting the modem.
On| None. Device is powered on.
Send/Receive
| Blinking| Scanning for downstream and upstream channels. Verify all cable
connections and try resetting the modem.
On| None. Connected to the Internet.
Online
| Off| Internet is not available. Verify all cable connections and try
resetting the modem.
Blinking| Downstream and upstream channel acquisition in progress. Verify all
cable connections and try resetting the modem.
On| None. Internet is available.
2.4 GHz
| On| None. Activity with a connected device on the 2.4 GHz wireless network.
Blinking| None. WiFi is enabled on the 2.4 GHz frequency.
5 GHz
| On| None. Activity with a connected device on the 5 GHz wireless network.
Blinking| None. WiFi is enabled on the 5 GHz frequency.
WPS LED| Blinking| None. WPS pairing is in progress with a WPS-enabled
wireless device.
On| None. A WPS-enabled wireless device is connected.
USB Port| N/A| There is no LED on the port.
Rear Panel Modem Lights
The lights below indicate the connection status of your WiFi cable modem. To troubleshoot any connection problems, use the table below.
| Light | Status | Problem |
|---|---|---|
| Ethernet | Off | Device is not connected to the port. Verify all cable |
connections and try resetting the modem.
Blinking or Solid Green| None. A device is connected to the port at 1000 Mbps
speeds and data is passing between cable modem and connected device.
Blinking or Solid Amber| None. A device is connected at 10/100 Mbps speeds and
data is passing between cable modem and connected device.
Manufacturer Resources
For more detailed technical information on the SBG6950, see the following resources.
- Arris_Surfboard_SBG6590_Data_Sheet [PDF]
- Arris_SBG6950AC2_SBG7400AC2_SBG7600AC2_UserGuide [PDF]
- ARRIS_SBG6950AC2_SBG7400AC2_SBG7600AC2_QSG [PDF]
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>