MIJIA C103 Robot Vacuum Cleaner User Manual

MIJIA C103 Robot Vacuum Cleaner

Safety Notice

Use restriction

• This product is only used for floor cleaning in domestic environments.
• Do not use it in outdoor, non-ground, commercial or industrial environments.
• This product is not intended to be used by persons with physical, sensory or intellectual disabilities, or persons without relevant experience and knowledge (including children) unless they are supervised or instructed by a guardian to ensure that they can use the product safely.
• Do not let children use this product as a toy. Please supervise children and pets to keep them as far away as possible when the host is working.
• If the power adapter is damaged, it must be replaced with a special component purchased from its manufacturer or service department.
• Do not place children pets or any objects on the stationary or running console.
• Do not place the cleaning brush in areas accessible to children.
• Do not use it in suspended environments (such as duplex floors, open balconies, and tops of furniture) without protective rails.
• Do not use it in environments above 35°C, below 0°C or where there are any liquids or sticky substances on the ground.
• Do not use it to clean up any burning objects.
• Please tidy up the wires on the ground at home before use to avoid dragging the host when it is running.
• Please put away fragile items and debris on the ground (such as vases, plastic bags, etc.) to avoid damage to valuables in your home due to obstruction or slight collision of the host during operation.
• Do not allow the host to absorb hard or sharp objects (such as decoration waste, glass, nails, etc.).
• Do not use mopping mode on carpets.
• Please clean and maintain the host and charging base when the power is off.
• Do not leave the main unit upside down on the ground for a long time.
• Do not use the laser ranging sensor as a handle to carry the host.
• Please use this product according to the instruction manual.
• Any losses caused by improper use shall be borne by the user.
• If you need to transport the product, please ensure that the host is turned off, and it is recommended to use the original packaging box for packaging protection.

Batteries and charging

• Do not use any third-party battery or charging dock. The host can only be used with the BLJ15W200060P-CA power adapter.
• Do not disassemble, repair or modify the battery or charging base.
• Do not place the charging base near a heat source (such as a radiator).
• Before scrapping the host, disconnect the power supply and remove the battery from the host for environmental protection.
• If not used for a long time, please turn off the host after full charge and put it in a cool and dry place.
• It is recommended to charge the battery at least every 3 months to avoid battery damage.

Environmental protection statement

The chemical substances contained in the lithium-ion battery built into this product will cause environmental pollution. Before scrapping, please have it removed by professionals and hand it over to a professional battery recycling agency for centralized disposal.

• Batteries must be removed from the appliance before disposal.
• When removing the battery, the appliance must be switched off.
• Batteries should be disposed of safely.

Battery Removal Procedure

The following information applies only to the discarded mopper and is not a daily operation instruction:

1. Let the sweeper run without touching the charging seat until the low power can not be cleaned;
2. Turn off the mop;
3. Remove the bottom shell of the sweeper;
4. Press the latch to pull out the battery connector and take out the battery.

Product introduction

Note: The product, accessories, user interface and other illustrations in the manual are schematic diagrams and are for reference only. Due to the update and upgrade of the product, the actual product and the diagram may be slightly different, please refer to the actual product.

Parts list
Accessories installed on the main machine:

Others:

Product introduction

Description of indicators on the host

• White Steady – Host status Normal
• white breath Medium charge (medium-high charge)
• white flash  Charging back or upgrading firmware
• Steady yellow Host Wi-Fi offline
• Yellow flicker Abnormal host status/reset Wi-Fi
• Yellow respiration Charging (low battery)
• Extinguish Shutdown/sleep state

Preparation before use

1. Remove the anti-collision strip

2. Install a side brush
   Take out the edge brush, install it to the buckle shown, and hear a “click”, indicating that the installation is in place.

3. Tear off the protective film of the charging seat, place it against the wall and connect the power supply Attention:
   • Do not place the charging base in direct sunlight.
   • Please ensure that no items are placed within 0.5 meters of the left and right sides of the charging seat and 1.5 meters in front of it.

4. Charge
   Place the console on the charging dock to charge.

Tip

• When charging for the first time, it is recommended to use it after full charging to protect battery performance.
•  After the host charging pole piece is aligned and placed on the charging seat shrapnel, it will automatically turn on, and cannot be turned off during charging

Network configuration

This product has been connected to MIJIA, can be controlled through the MIJIA APP or Xiaoai students, and can be connected with other products.

Connect to the MIJIA APP

10981711

1. Scan the QR code, download and install the MIJIA APP. Users who have installed the Mijia APP will directly enter the device connection page. Or search for “MIJIA ” in the APP store to download and install the MIJIA app.
2. Open the home page of the MIJIA APP, click”+” in the upper right corner of the page, and add devices as prompted by the APP.

Tip:
This product only supports Wi-Fi networks in the 2.4GHz band. Due to the upgrade and update of the MIJIA APP, the actual operation may be slightly different from the above description, please follow the instructions in the current MIJIA APP.

How to connect the Xiaomi sweeping robot 3C, please check the following reference website:
Android:
https://www.youtube.com/watch?v=PRL-aAJY _8c
Apple/I OS:

https://www.youtube.com/watch?v=5oUuKpNH1 N8&t=66s

When connecting to the APP, you may encounter problems and solutions refer to the following.

Fault phenomenon

Reset the Wi-Fi

Please press and hold the and keys at the same time for 7 seconds when the phone is powered on. After hearing the voice prompt, the Wi-Fi reset is successful.

• Press and hold the key for 5 seconds until you hear a “beep” sound.
• Press and hold the key again for 5 seconds. After hearing the voice

prompt, the host will restart and related settings such as scheduled cleaning and Wi-Fi will be restored to the factory state.

Use

Tip: For the first time, please complete the quick drawing according to the APP prompts. It is recommended to follow the host throughout the whole process to help clean up the items that may affect the work of the host. Please ensure that the host starts from the charging dock and removes the ground obstacles to ensure the accuracy of the drawing. If some areas may jam the host or scratch the furniture surface when the host is running, you can set a restricted area in the mobile APP to prevent the host from entering the above area.

Starting mop

1. Press and hold the release button of the two-in-one water tank, take out the 2-in-1 water tank, open the water tank cover, inject water into the water tank cover. Notice:
2. Please take out the 2-in-1 water tank and add water. Do not add hot water, detergent, disinfectant, etc. to avoid damaging the machine.
3. New products will undergo a water test before leaving the factory, and there may be a small amount of water stains remaining. This is normal.
4. Install the mop assembly on the two-in-one water tank in the direction shown in the figure.
5. Load the two-in-one water tank with the mop component installed into the host in the direction shown in the figure. When you hear “click”, it means that the water tank is installed in place. Press to start the mop.
   Note : After mopping the floor, please pour out the remaining water in the 2-in-1 tank in time, and clean and dry the mop to avoid odour and mildew. If you only need to use the sweeping function, please remove the mop assembly according to the figure:

Note : When the host is running, set up a virtual wall or exclusion zone in the carpet area of your home to avoid carpet entanglement.

Pause

When the host is running, press any key to pause, and then press to continue. Tip : After the host is suspended or in standby mode for 10 minutes, it enters the hibernation state. You can press any key to wake it up.

Add water or a clean mop

When the host is working, please stop, take off the two-in-one water tank, add water or clean the mop, and then put it back, and press to continue working.

Recharge
During work, press the key to stop work, and press the key again to start to recharge; When the battery in standby mode and the charging base is not connected, press start the recharge. When the work ends or the power is too low, the host automatically recharges.

Do not disturb mode

In this mode, the host does not perform breakpoint continued scanning, scheduled cleaning, and active voice broadcast, and the indicator is off after 10 seconds of charging. This mode can be turned on or off in the APP. Tip: For more functions, please refer to the APP. The specific situation of each function is subject to the APP.

Care and maintenance

Clean the 2-in-1 water tank and filter

1. Take out the two-in-one water tank, open the tank cover and dust box cover respectively, dump the remaining water and garbage, and then clean the two-in-one water tank with a cleaning brush.
   Notice:
   • Do not shower or soak the 2-in-1 water tank.
   • Clean the 2-in-1 water tank regularly to prevent dirt inside the tank from affecting the cleaning effect.

2. Remove the filter and clean the filter with a cleaning brush.

Tip: If necessary, you can also clean the filter with water, and be sure to put it back after completely drying. Frequent washing is not recommended.

Cleaning mop

Remove the mop from the mop holder and wash to dry.

Clean the sensor and charging pole

Use a soft cloth to clean the individual sensors and charging poles every 3 months.

Clean the side brush and main brush

1. Pull out the edge brush upward.
2. Hold the two main brush cover clips, remove the main brush cover, take out the main brush, and pull out the main brush bearing.
3. Use a cleaning brush to clean the side brush and main brush.

Q &A.

Troubleshooting

When the host is faulty, a voice message may be displayed. Refer to the following to rectify the fault in a timely manner.

Basic parameter

Host machine

Charging base

Power adapter

Warranty

Warranty description

[AFTER-SALES SERVICE] –
We value your satisfaction. All of our products come with a 24-month warranty and lifelong technical support. If you have any questions about our MIJIA Robot Vacuum Cleaner 3C, please feel free to contact us, and our Dysokan after-sales personnel will provide you with professional technical support.
URL:
https://www.amazon.com.au/stores/page/FEDSOSAE-5153-4307-BD7E-B98406516608

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>