zimi Single and Dual Blind Controllers Instruction Manual
- June 4, 2024
- Zimi
Table of Contents
Let’s get connected.
Single and Dual Blind Controllers.
Important – Read before installing.
Must only be installed by a LICENSED ELECTRICIAN to local wiring regulations
Powermesh devices must only be connected with the Active and Neutral from the
same RCD.
AVOID THE RISK OF ELECTRIC SHOCK
Once the product has been fastened to the wall, ensure the screw caps are
inserted firmly into place over the screw mounting holes.
Failure to follow these instructions can result in serious injury or death.
Surge protection is recommended at the main switchboard. Products damaged by
power surges are not covered by warranty.
Megger testing may lead to low readings due to electronic components so
disconnect all electronic devices before taking a reading. Install the
included warning sticker with circuit detail in the main electrical
switchboard.
Using the Blind Controller.
Identifying the Blind Controllers.
Single Blind Controller.
Specifications ** Part Number
**
White | PMBC2 |
---|---|
Black | PMBC2BK |
Compatible Loads
M | Small motor rating: M.40 |
---|
Rated Loads
600W (2.5A) max, 230V~ 50Hz
Dual Blind Controller.
Specifications
Part Number
White | PMBC4 |
---|---|
Black | PMBC2BK |
M | Small motor rating: M.40 |
--- | --- |
Rated Loads
600W (2.5A) max per channel, 230V~ 50Hz
Pair and set up with Zimi.
- Download the Zimi App.
- Choose ‘Add New Device’.
- Follow the on-screen instructions.
Download Zimi App.
Point your phone camera at the QR code to open the app store.
Zimi Cloud Connect.
Enjoy the full experience with all your Zimi devices.
Want to learn more or need help?
Enjoy all the features to make your life easier. Visit our website for tips,
tricks and help.
support.zimi.life
Switch, app and voice control. Smart Blinds| Automatically open and close. Schedules| Control all your connected blinds. Double press
Status Indicator.
| Blue| Ready to pair.
‘Add New Device’ in Zimi to pair and complete setup.
---|---|---
| White| Setup is complete.
This device has been paired and setup completed.
| White pulsing| Action in progress.
This lets you know an automatic function is being activated.
| Blue & White pulsing| Identify device.
This shows the device when updating its settings.
| Red| Device problem.
Please refer to support to resolve the problem.
| Off| Indicator is off.
The status indicator can be turned off and on in settings.
Manufacturer’s Warranty This product has been manufactured to the highest
quality standards. This product is warranted to the original purchaser and is
not transferable. The product is guaranteed to be free from defects in
workmanship and parts for a period of 1 Year from the date of purchase.
Defects that occur within this warranty period, under normal use and care will
be repaired, replaced or refunded. The benefits conferred by this warranty are
in addition to all other rights and remedies of the consumer under
Commonwealth, State and Territory laws in relation to the goods or services to
which this warranty relates and Australian Consumer Law. Risk in regard to the
product to be repaired shall at all times remain with the Purchaser. The
warranty is given on the condition that the product to which it applies is
used for the purpose and in the manner intended by its construction and for no
other purposes whatsoever. Zimi Ltd shall not be responsible for damage of any
kind, caused by accidents, power surges, electrical storm damage, incorrect
power current, infestation (vermin or insect), incorrect installation,
incorrect electricity or plumbing installation, improper use of controls or
failure to use the unit in accordance with the operating instructions, general
misuse or abuse or from normal wear and tear. Any attempt by an unauthorized
person to repair or tamper with the equipment shall render the warranty null
and void. Goods presented for repair under this warranty may be replaced by
refurbished goods of the same type rather than being repaired. Refurbished
parts may be used to repair the goods. Zimi Ltd’s liability under this
warranty is limited to the replacement and/or repair of the defective parts
within the warranty period and does not extend to installation or removal of
the product. Acceptance of liability by Zimi Ltd contained herein is to the
exclusion of any other remedy
whatsoever and howsoever arising in respect of any equipment to which it
applies.
Proof of Purchase Please keep your purchase docket or receipt as proof of
purchase and as proof of the date on which the purchase was made. The purchase
docket or receipt must be presented with the warranty when making a claim
under this warranty. Failure to produce documentary proof of the date of
original acquisition by the original Purchaser will result in a charge being
levied for work done, labor and parts supplied. Likewise, a charge will be
made for any calls following the warranty claim where no fault is found with
the unit.
Service during the warranty period The first point of contact for product
issues is the place of purchase. The product must be returned to the original
place of purchase for product repair, replacement or refund. Please ensure the
product is properly packaged so as to ensure that no damage occurs to the
product during transit and make sure that you have included an explanation of
the problem. In the event of goods requiring repair under the manufacturer’s
warranty, the owner is responsible for the cost of transportation. Should the
goods be found to be in sound working order the owner might be charged a fee.
This warranty is given by Zimi Ltd, 14 Millennium Circuit, Helensvale, QLD
4212.
Safety Warnings Read all instructions and safety information. All
electrical work must only be undertaken after disconnection of the power by
removing fuses or turning off the circuit breaker, to ensure all pole
disconnection from the electrical supply. All electrical work must be carried
out by a licensed and qualified electrician and in accordance to AS/NZS 3000
Wiring Rules and applicable local authority regulations. This product is not
intended for use by persons (including children) with reduced physical,
sensory
or mental capabilities, or lack of experience and knowledge unless they have
been given supervision or instruction concerning use of the product by a
person responsible for their safety. Young children should be supervised to
ensure they do not play with the unit. Do not cut or notch joists, beams and
rafters to install the unit. Do not damage hidden electrical wiring or
utilities when cutting. The product must be installed so switches and other
controls cannot be touched by a person in the bath or shower. Do not install
the product in a location where water will splash onto it. Check and confirm
that all connections are proper and secure to prevent causing property damages
or injury. Do not install it outdoor where it could be exposed to water or
moisture (indoor use only).
Trademarks Zimi and Powermesh and their respective logos are registered
trademarks of Zimi Ltd. Google and Google Play are trademarks of Google LLC.
Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc. or its
affiliates. Apple, the Apple logo, Apple Watch and iPhone are trademarks of
Apple Inc., registered in the U.S. and other countries. App Store is a service
mark of Apple Inc., registered in the U.S. and other countries. Copyright ©
2022 Zimi Ltd. All rights reserved.
14 Millennium Circuit
Helensvale QLD 4212
Australia.
www.zimi.life
Documents / Resources
| zimi
Single and Dual Blind
Controllers
[pdf] Instruction Manual
Single and Dual Blind Controllers
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>