FIGHOW WP71+WD61 Water Detector with WP71 Motion Sensor Alarm User Manual

FIGHOW WP71+WD61 Water Detector with WP71 Motion Sensor Alarm User Manual

At a glance

WP71 Motion Sensor Alarm

WP71 Motion Sensor Alarm :
Volume: Short press LN to adjust the panel volume.((Turn to the maximum or minimum sound, the LED light will flash 2 times) Arming/Disarming: When the panel is power-on, short press Il to arming/disarm the panel. (One beep sound’ -arming, ‘two beeps sound ‘-disarm-ing, “Three beeps sound”-Stay) Tone: Shot press II to select different alarm Sounds.

Wi-Fi connected

WP71 two boot modes

| Insert the USB/ put on the battery
Long press ( ] button, WP71 From start up to shutdown| Will beep once and red light will flash once to indicate that it is off

Water Leak Detector

• Indicator: For reflecting the status of the detector
• Sensor: Detecting Dripping
• Alarm: Alarm Sound
• Test Key: Pairing, testing., pausing alerts
• Probe: Detecting water seepage
• Install Batteries: AAA battery 2

Specifications

WP71 Motion Sensor Alarm

Power Supply| 3 AAA batteries or

5V USB Cable

Operating Humidity| <90%
Standby/Working/

Shutdown Current

| <30mA /<lOOmA/ <lOOuA
Infrared Detection Range| <8 meters
Alarm Volume| 120dB
Detection angle| 110 Degrees
Water Leak Detector

Working Voltage| 2xAAA Batteries
Transmission Frequency| 433MHz
Waterproof Level| IP66
Wireless Transmission| > 1OOm ( open area)

Alarm Duration

| 15s/Firsttime (The second alarm sounds every 15s and lasts for

24 hours.)

Installing your Device
Place the sensor of the water leak detector in the
the place where you need to strengthen the water level
detection.

Tuya Smart Home Application
A Wi-Fi router supports 24GHz (not 5 GHz). Please check your network information before you try to connect.

Download the TuyaSmart app from the App Store(0S devices) or Google Play(Android devices)

Connecting to a Wi-Fi Network
Open the app, tap “+” icon at the top right corner and select”Connector(Wi- Fi)”in”Others”

Connect your phone with your family Wi-Fi network Select 24 GHz WFi Network and enter password Fyour s home t to be 24Grte.Carson ow as no
Note: Please make sure the Wi-Fi network is 2.4GHz before you start to connect WP71 Motion Sensor Alarm

WP71 Motion Sensor Alarm enters into the pairing mode. Please plug in a USB or 3xAAA battery, it will beep twice and power on automatically. Entering the WiFi Press and hold the Volume
key” I.l and Tone key LOIkeys of the host at the same time, the panel will start fast flashing of red light. 6

Click to confirm that the light is flashing rapidly and then click next to start the search and scan

Alarm control with Tuya Smart Home

• Armed: Fully arming the system. All detectors are active.
• Disarmed: The system is completely disarmed. In this mode, only detectors set to zone type”24H’can trigger the alarm.
• Home: Allows you to arm the system when you are at home.g.at night). In this mode, detectors set to the “partial” zone type will not trigger the alarm.
• SOS: Allows you to activate the siren immediately.
• History records: Check the operation records such as arming, disarming, and alarming.
• Accessories: Allows you to access the list of accessories (detectors and remote controls) and to pair up new accessories.
• Settings: Allows you to access all the alarm system settings.

Using your device

Detecting Dripping

Note:

• Two detection sensors of parallel lines will immediately alarm when they detect water, and two sensors of diagonal lines will not alarm when they detect water at the bottom of the detector.
• If the device is still not dehydrated after the detector alarm is over, then the flood detector will continue to
• alarm every 15S until the dehydration or press the button to cancel the alarm. it will not make a regular alarm prompt if it’s still immersed in water after 24 hours.

Removing the alarm
Press the button to cancel the alarm.

Low power prompt Red light is flashing Add detector and remote control Tantor the APD click on accessories Press Upper right corner “+” Accessories Detector Remote control No accessory
Then press the water leak detector “test” button or press the remote control button. Start scanning and display a counter To associate your additional detectors or remote control, simply trigger them

Note: The WP71 Motion Sensor Alarm has made two beeps sound- successful pairing/One beep sound- already paired/Three beeps sound-fully equipped with detectors or remote control)

Zone attribute setting for detectors
Setting the zone attribute of your detectors defines when they can be triggered.

Then click on the Zone attribute

Normally active when the system is fully or partially armed Partial: detector active when the system is fully armed, it will be inactive when the system is partially armed
24h: detector active regardless of the control panel mode farmed, disarmed or partial)

Setting Alaram

• Arm delay: arm the panel after a preset time
• Timer: arm the panel at the preset date/time
• Infrared detection switch: panel motion detection function.
• Alarm volume: 4 levels adjustable
• Alarm light switch: panel flashing light
• Alarm time: 0-255 seconds adjustable
• Alarm tone type: 5 types of adjustable
• Arm or disarm message push switch: app push up for notification

WP71 Motion Sensor Alarm

WP71 motion sensor alarm is intended to detect When people enter your shop or your home. Depending on your need, it will sound a loud siren |alarm or a friendly chime.

When you use the WP71 motion sensor alarm alone, turn on the armed state. If there is a theft into your home or a prank, an alarm will sound to remind you.

Attention

If the WP71 needs to be connected to the water detector, the infrared sensor must be turned off. If the WP71 is used alone, the infrared sensor must be turned on. Turn off the alarm WP71 Motion Sensor Alarm is connected to TuyaSmart, you can set it to disarm in the app or remote control and the alarm will be canceled. (But if used with a water detector, Please turn off the alarm sound of the WP71 Wi-Fi sensor and water leak detectors separately)

Powering up the control unit

1. 0pen the battery compartment on the back of the control panel and insert 3 AAA batteries, observing the correct polarity. Close the battery compartment.
2. Connect the control panel to a power outlet using the supplied AC adapter and USB cord.

Charging the batteries:
Remove the cover on the back to access the battery compartment. Remove the used batteries and replace them with equivalent models(2 x AAA batteries). Put the cover back on the test of your detector.
Warning:
Return to factory settings: Unplug the power, Press and hold Ill buttons while plugging in the power cord. The control panel will emit 10 long beeps and the LED will flash 10 times, releasing the button.The plant unit is restored to factory settings, the main unit is in the armed state, and all the detectors have been deleted. Low battery prompt: When the host has a low battery, it flashes 3 times every 40 seconds and the host buzzer sounds three beeps sound and sends a low battery alert to the bound mobile phone through the network.(Limited to WP71) Customer Service

• Warranty:12-month Limited Warranty Email:FIGHOW123@163.com (Thank you for choosing us. We are online 24 hours a day to answer your questions. FIGHOW Gives you a 100% satisfied buying experience.)

Troubleshooting

The WP71 motion sensor alarm could not be connected to the Wi-Fi network or the connection is unstable?
The product supports only a 2.4GHz (not 5 GHz) network Check the name of the network and the password. Please try to avoid special characters. The device should be placed within the signal coverage area of the router. Please keep the distance between WP71 and router 30 meters. Connect to wifi, please reduce the interference, thick walls, etc.

The sensors do not work?
Pull out the insulation sheet before using it.
Check the battery capacity Check if the sensor is installed correctly.

Battery recycling
Do not dispose of used batteries in your household

FCC Warning

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for help.

Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>