FIGHOW WD61 Water Detector with WP71 Motion Sensor Alarm User Manual

June 5, 2024
FIGHOW

BUILD SMART HOME
MODELWD61+WP71
Water Detector with wP71 Motion Sensor Alarm
User Manual

At a glance

FIGHOW WD61 Water Detector with WP71 Motion Sensor Alarm -
fig

WP71 Motion Sensor Alarm

FIGHOW WD61 Water Detector with WP71 Motion Sensor Alarm - fig
1

WP71 Motion Sensor Alarm:

Volume: Short press to adjust the panel volume. ((Turn to the maximum or minimum sound, the LED light will flash 2 times)
Arming/Disarming: When the panel is power-on, short press to arming/disarming the panel. (‘One beep sound’ –arming, ‘two beeps sound ‘–disarm­ ing, “Three beeps sound”–Stay)

Tone: Shot press to select different alarm sound

WP71 red light on when a person is moving Wi-Fi not connected
Wp71 blue light on when a person is moving Wi-Fi connected
WP71 two boot modes Insert the USB/ put on the battery
Long press button, wp71 from start-up to shutdown Will beep once and the red

light will flash once to indicate that it is off

Water Leak Detector:
Indicator.For reflecting the status of the detector
Sensor.Detecting Dripping
Alarm: Alarm Sound
Test Key. Pairing, testing, pausing alerts
Probe: Detecting water seepage
Install Batteries AAA battery2

Specifications

WP71 Motion Sensor Alarm

Power Supply| 3 AAA batteries or 5V USB Cable
Operating Humidity| <90%
Standby/Working/Shutdown Current| <30mA /<100mA/ <1OOuA
Infrared Detection Range| <8 meters
Alarm Volume| 120d8
Detection angle| 110Degrees
Water Leak Detector
Working Voltage| 2xAAA Batteries
Transmission Frequency| 433MHz
Waterproof Level| IP66
Wireless Transmission| >100m (open area)
Alarm Duration| 15g/First time (The second alarm sounds every 15s and lasts for 24 hours.)

Installing your Device

(D Place the sensor of the water leak detector in the place where you need to strengthen the water level detection.

FIGHOW WD61 Water Detector with WP71 Motion Sensor Alarm - fig
10

Tuya Smart Home Application
  wifi router supporting the 24GHz (not S GHz). Please check your network information before you try to connect

Download the TuyaSmart app from the App Store(Los devices) or Google Play(Android devices)

Connecting to a Wi-Fi Network

  1. Open the app, tap the “+” icon at the top right corner, and select”Connector(Wi-Fi” in”Others”FIGHOW WD61 Water Detector with WP71 Motion Sensor Alarm - fig 14

  2. Connect your phone to the family Wi-Fi networkFIGHOW WD61 Water Detector with WP71 Motion Sensor Alarm - fig 15
    Note:
    Please make sure the Wi-Fi network is 2.4GHz before you start to connect the WP71 Motion Sensor Alarm to the network.

  3. WP71 Motion Sensor Alarm enters into the pairing mode.FIGHOW WD61 Water Detector with WP71 Motion Sensor Alarm - fig 16 Please plug in US8 Or 3xAAA batteries, it will beep twice and power on automatically.
    Entering the WiFi
    Press and hold the Volume key and Tone key  keys of the host at the same time, and the panel will start fast flashing of red light.

  4. Click to confirm that the light is flashing rapidly and then dick next to start the search and scanFIGHOW WD61 Water Detector with WP71 Motion Sensor Alarm - fig 18

Alarm control with Tuya Smart Home

FIGHOW WD61 Water Detector with WP71 Motion Sensor Alarm - fig
22

-Armed Fully arming the system. All detectors are active.
-Disarmed: The system is completely disarmed. In this mode, only detectors set to zone type”24H” can trigger the alarm.
-Home: This allows you to arm the system when you are at home(e.g.at night). In this mode, detectors set to the “partial” zone type will not trigger the alarm.
-505Allows you to activate the siren immediately.

FIGHOW WD61 Water Detector with WP71 Motion Sensor Alarm - fig
23History records: Check the operation records such as arming, disarming, and alarming.
Accessories: This allows you to access the list of accesso­ Aries (detectors and remote controls) and to pair up new accessories.
Settings: Allows you to access all the alarm system settings

Using your device

  1. Detecting DrippingFIGHOW WD61 Water Detector with WP71 Motion Sensor Alarm - fig 24 Note:
    **** Two detection sensors of parallel lines will immedi­ lately alarm when they detect water, and two sensors of diagonal lines will not alarm when they detect water at the bottom of the detector.
    If the device is still not dehydrated after the detector alarm is over, then the flood detector will continue to alarm every 15 until the dehydration or press the button to cancel the alarm. it will not make a regular alarm prompt if it’s still immersed in water after 24 hours.

  2. Removing the alarmFIGHOW WD61 Water Detector with WP71 Motion Sensor Alarm - fig 6

  3. Low power prompt

  4. Add detector and remote control

  5. Enter the APP, and click on accessories.FIGHOW WD61 Water Detector with WP71 Motion Sensor Alarm - fig 4

  6. Press Upper right corner “+”FIGHOW WD61 Water Detector with WP71 Motion Sensor Alarm - fig 2

  7. Then press the water leak detector “test” button or press the remote control on any button. Start scanning and display a counter
    To associate your additional detectors or remote control simply triggers them.FIGHOW WD61 Water Detector with WP71 Motion Sensor Alarm - fig
4 Note: The WP71 Motion Sensor Alarm has made two beeps sound- successful pairing/One beep sound- already paired/Three beeps sound-fully equipped with detectors or remote control)

  8. Connection succeededFIGHOW WD61 Water Detector with WP71 Motion Sensor Alarm - fig 7

Zone attribute setting for detectors

Setting the zone attribute of your detectors defines when they can be triggered.FIGHOW WD61 Water Detector with WP71 Motion Sensor Alarm - fig
8

In the Accessories/Detectors menu, click on the detector you wish to set up FIGHOW WD61 Water Detector with WP71 Motion Sensor Alarm - fig
9

Then click on the Zone attributeFIGHOW WD61 Water Detector with WP71 Motion
Sensor Alarm - fig 12

Normal: active when the system is fully or partially armed
Partial: the detector is active when the system is fully armed, it will be inactive when the system is partial­y armed
24h: detector active regardless of the control panel mode(armed, disarmed, or partial)

Setting menu

FIGHOW WD61 Water Detector with WP71 Motion Sensor Alarm - fig
13

Arm delay: arm the panel after a preset time
Timer: arm the panel at the preset date/time
Infrared detection switch: panel motion detection function.
Alarm volume: 4 levels adjustable
Alarm light switch: panel flashing light
Alarm time: 0-255 seconds adjustable
Alarm tone type:5 types adjustable
Arm or disarm message push switch: app push up for notification

WP71 Motion Sensor Alarm

FIGHOW WD61 Water Detector with WP71 Motion Sensor Alarm - fig
17 wP71 motion sensor alarm is intended to detect When people enter your shop or your home.
Depending on your need, it will sound like a loud siren alarm or a friendly chime.

Attention;

FIGHOW WD61 Water Detector with WP71 Motion Sensor Alarm - fig
19

If the WP71 needs to be connected to the water detector, the infrared sensor must be turned off
If the WP71 is used alone, the infrared sensor must be turned on.
Turn off the alarm
wp71 Motion Sensor Alarm is connected to
TuyaSmart, you can set it to disarm in the app or remote control and the alarm will be canceled. (But if used with a water detector, Please turn off the alarm sound of the WP71 Wi-Fi sensor and water leak detectors separately)

Powering up the control unit

  1. Open the battery compartment on the back of the control panel and insert 3 AAA batteries, observing the correct polarity. Close the battery compartment.
  2. Connect the control panel to a power outlet using the supplied AC adapter and USB cord.

FIGHOW WD61 Water Detector with WP71 Motion Sensor Alarm - fig
21

Charging the batteries:

FIGHOW WD61 Water Detector with WP71 Motion Sensor Alarm - fig
20

  1. Remove the cover on the back to access the battery compartment.
  2. Remove the used batteries and replace them with equivalent models(2 x AAA batteries).
  3. Put the cover back on the test your detector.

Warning:

Return to factory settings: Unplug the power, press and hold buttons while plugging in the power cord, The control panel will emit 10 long beeps and the LED will flash 10 times, releasing the button.The plant unit is restored to factory settings, the main unit is in an armed state, and all the detectors have been deleted.

Low battery prompt: When the host has a low battery it flashes 3 times every 40 seconds and the host buzzer sounds three beeps sound and sends a low battery alert to the bound mobile phone through the network. (Limited to wp71)

Customer Service
Warranty:12-month Limited Warranty
Email-FIGHOW123@163.com
(Thank you for choosing us. We are online 24 hours a day to answer your questions. FIGHOW Give you a 100% satisfied buying experience.)

Troubleshooting

The WP71 motion sensor alarm could not be connect­ ed to the Wi-Fi network or the connection is unstable ?
a.Product supports only a 24GHz (not 5 GHz) network.
b.Check the name of the network and the password. Please try to avoid special characters.
c.The device should be placed within the signal coverage area of the router. Please keep the distance between WP71 and the router 30 meters.
d.Connect to wif, please reduce the interference, thick walls, etc.
2. The sensors do not work?
a. Pull out the insulation sheet before using.
b. Check the battery capacity
c. Check if the sensor is stalled correctly.

Battery recycling
Do not dispose of used batteries with your household waste, but in the recycling bins provided.

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

FIGHOW WD61 Water Detector with WP71 Motion Sensor Alarm - icon
5

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals