BLACK DECKER GL250, GL310, GL360 Strimmer Bump Feed Line Instruction Manual

June 3, 2024
Black Decker

BLACK DECKER GL250, GL310, GL360 Strimmer Bump Feed Line

BLACK-DECKER-GL250-GL310-GL360-Strimmer-Bump-Feed-Line-Instruction-Manual-
product

Intended use
Your BLACK+DECKER™· GL250, Gl310, GL360 trimmer has been designed for! rimming and finishing lawn edges and lo cul grass in confined spaces. This appliance is intended for consumer use only.

Safety instructions

Warning
When using mains-powered appliances, basic safety precautions, including the following, should always be followed to reduce the risk of fire, electric shock, personal injury and material
damage.

Warning
 When using the machine the safety rules must be followed. For your own safety and bystanders please read these instructions before operating the machine. Please keep the instructions safe for later use.

  •  Read all of this manual carefully before operating the appliance.
  •  The intended use is described in this manual. The use of any accessory or attachment or the performance of any operation with this appliance other than those recommended in this instruction manual may present a risk of personal injury.
  •  Retain this manual for future reference.

Using your appliance
Always take care when using the appliance.

  • Always use safety glasses or goggles.
  • Never allow children or people unfamiliar with the instructions to use the appliance.
  • Do not allow children or animals to come near the work area or to touch the appliance or power supply cord.
  •  Close supervision is necessary when the appliance is used near children.
  •  This appliance is not intended for use by young or infirm persons without supervision.
  •  This appliance is not to be used as a toy.
  •  Only use the appliance in daylight or with good artificial light.
  •  Use in a dry location only. Do not allow the appliance to become wet.
  •  Do not immerse the appliance in water.
  •  Do not open the body casing. There are not user-serviceable parts inside.
  •  Do not operate the appliance in explosive atmospheres, such as in the presence of flammable liquids, gases or dust.
  •  To reduce the risk of damage to plugs or cords, never pull the cable to remove the plug from a socket.

Safety of others

  • This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
  •  Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

Residual risks
Additional residual risks may arise when using the tool which may not be included in the enclosed safety warnings. These risks can arise from misuse, prolonged use etc. Even with the application of the relevant safety regulations and the implementation of safety devices, certain residual risks can not be avoided. These include:

  •  Injuries caused by touching any rotating/moving parts.
  •  Injuries are caused when changing any parts, blades or accessories.
  •  Injuries caused by prolonged use of a tool. When using any tool for prolonged periods ensure you take regular breaks.
  •  Impairment of hearing.
  •  Health hazards caused by breathing dust developed when using your tool (for example:- working with wood, especially oak, beech, and MDF.)

After use

  •  When not in use, the appliance should be stored in a dry, well-ventilated place out of reach of children.
  •  Children should not have access to stored appliances.
  •  When the appliance is stored or transported in a vehicle it should be placed in the boot or restrained to prevent movement following sudden changes in speed or direction.

Inspection and repairs

  • Before use, check the appliance for damaged or defective parts. Check for breakage of parts and any other conditions that may affect its operation.
  •  Do not use the appliance if any part is damaged or defective.
  •  Have any damaged or defective parts been repaired or replaced by an authorized repair agent?
  •  Never attempt to remove or rep/ace any parts other than those specified in this manual.

Using an extension cable

  • Always use an approved extension cable suitable for the power input of this appliance (see technical data). The extension cable must be suitable for outdoor use and marked accordingly. Up to 30 m of 1.5 mm2 HO5W-F extension cable can be used without loss of product performance. Before use, inspect the extension cable for signs of damage, wear and aging. Replace the extension cable if damaged or defective. When using a cable reel, always unwind the cable completely.

  • Additional safety instructions for grass trimmers

  • Warning! Cutting elements continue to rotate after the motor is switched off.

  •  Be familiar with the controls and the proper use of the appliance.

  •  Before use, check the power supply cord and extension cord for signs of damage, aging, and wear. If a cord becomes damaged during use, disconnect the cord from the main supply immediately.

  • DO NOT TOUCH THE CORD BEFORE DISCONNECTING THE SUPPLY.

  •  Do not use the appliance if the cords are damaged or worn.

  •  Wear stout shoes or boots to protect your feet.

  •  Wear long trousers to protect your legs.

  •  Before using the appliance, check that your cutting path is free from sticks, stones, wire and any other obstacles.

  •  Only use the appliance in the upright position, with the cutting line near the ground. Never switch the appliance on in any other position.

  •  Move slowly when using the appliance. Be aware that freshly cut grass is damp and slippery.

  • Do not work on steep slopes. Work across the face of slopes, not up and down.

  • Never cross gravel paths or roads while the appliance is running.

  • Never touch the cutting line while the appliance is running.

  •  Do not put the appliance down until the cutting line has come to a complete standstill.

  • Use only the appropriate type of cutting line. Never use metal cutting lines or fishing line.

  •  Be careful not to touch the line trimming blade.

  •  Take care to keep the main cable away from the cutting line. Always be aware of the position of the cable.

  •  Keep hands and feet away from the cutting line at all times, especially when switching on the motor.

  •  Before using the appliance and after any impact, check for signs of wear or damage and repair as necessary.

  •  Never operate the appliance with damaged guards or without guards in place.

  •  Take care against injury from any device fitted for trimming the filament line length. After extending the new cutter line always return the machine to its normal operating position before
    switching on.

  •  Always ensure that the ventilation slots are kept clear of debris.

  •  Do not use the lawn trimmer (edge trimmer), if the cords are damaged or worn.

  •  Keep extension cords away from cutting elements.

  • Wear safety glasses or goggles when operating this appliance.

  • Wear suitable ear protectors

  • when operating this appliance.

  • Always remove the plug from

  • the socket before inspecting a damaged cable. Be careful not to use your strimmer if the cable is damaged.

  • Beware of flying objects. Keep bystanders away from the cutting area.

  • Do not expose the appliance to rain or high humidity.

  • Directive 2000/14/EC guaranteed sound power.

Electrical safety

This appliance is double. insulated; therefore no earth wire is required. Always check that the power supply corresponds to the voltage on the rating plate.

  •  If the supply cord is damaged, it must be replaced by the manufacturer o’. an authorized BLACK+DECKER Service Centre in order to avoid a hazard.
  •  Electric safety can be further improved by using a high-sensitivity 30 mA Residual Current Device (RCD).

Features

BLACK-DECKER-GL250-GL310-GL360

This appliance includes some or all of the following features.

  1.  On/off switch
  2.  Handle
  3. Cable restraint
  4.  Power inlet
  5. Second handle
  6.  Guard
  7.  Line trimming blade
  8.  Cutting line
  9.  Spool housing
  10. Head

Assembly

Warning! Before assembly, make sure that the tool is switched off and unplugged. Attaching the second handle (fig. A) (GL310 & GL360 only)

  •  Slide the second handle (5) onto the main handle (2) in an upwards direction
  •  Secure the second handle In a place with the two screws (19} provided.

Fitting the guard (fig. B)

  • Place the guard onto the tool as shown.
  •  Firmly press the guard (6) until it snaps _ into place.
  •  Secure the guard with the screw (11).
  • Warming Never uses the tool unless the guard Is properly fitted.
  • releasing the cutting line
  • n transit, the culling line is taped lo the spool housing.
  • Remove the tape holding the cutting line (8) lo the spool housing (9).

Connecting the tool to the mains (fig. C)

  •  Connect the female plug of a suitable extension cable to the power inlet (4).
  •  Loop the cable through the cable restrain! (3).
  •  Insert the mains plug into a mains outlet.
  • For wired-in cable units: Make sure the cable is looped through the cable restraint prior to connecting the plug outlet.

Trimming

  •  Hold the tool as shown in fig. D.
  •  Gently swing the summer from side lo side.
  •  When cutting long grass, work in stages from the lop. Take small cuts.
  •  Keep the tool away from hard objects and delicate plants.
  •  Cutting line will wear faster and require more feeding if the cutting Is done along pavements or other abrasive surfaces or heavier weeds are being cul.
  •  As you use the trimmer, the string will get shorter due to wear. Gently bump the unit on the ground whilst running and the line will feed.
  •  If the tool starts running slowly, reduce the load

Fitting a new spool of the cutting line (fig. E • F)
Replacement spools of cutting line are available from your BLACK+DECKER dealer (cal. no. A6226).

  • Keep the tabs (12) depressed and remove the spool cover (13) from the housing (9).
  •  Remove the empty spool (14) from the spool housing.
  •  Remove any dirt and grass from the spool cover and housing
  •  Take the new spool and unwind approximately 10 cm of the cutting line.
  •  Feed the cutting line through the eyelet (15).
  •  Push the spool onto the drive shaft (16) and rotate it slightly until it is seated Make sure that the cutting line is not trapped under the spool and that 10 cm of cutting line protrudes from the housing.
  •  Align the tabs (12) on the spool cover with the holes in the housing (15).
  •  Push the cover onto the housing until it snaps securely into place.
  • Warning! If the cutting line protrudes beyond the trimming blade (7). cut it off so that it must reach the blade.

Winding a new cutting line onto an empty spool (fig. G – I)
You may wind a new cutting line onto an empty spool. Replacement packs of cutting line are available from your BLACK+DECKER dealer [cat no. A6170 (25 m), A6046 37,5 m) & A6171 (40 m))

  •  Remove the empty spool from the tool as described above.
  •  Remove any remaining cutting line from the spool.
  •  Feed 2 cm of culling line into one of the holes (17) In the spool as shown.
  • Wind the cutting line onto the spool in the direction of the arrow (18). Make sure to wind the line on neatly and in layers. Do not criss-cross
  •  Let the line protrude approximately 10 cm from the spool and hold a finger on the line to keep it in place
  • Proceed as described above to fit the spool on the tool.
  • Warning! Only use the appropriate type of BLACK+DECKER cutting line

Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:

  • Safely dispose of the old plug.
  •  Connect the brown lead to the live terminal in the new plug.
  •  Connect the blue lead to the neutral terminal.
  • Warning I No connection is to be made to the earth terminal. Follow the fitting instructions supplied with good-quality plugs. Recommended fuse: 5 A.

Troubleshooting

If your tool seems not to operate properly, follow the instructions below. If this does not solve the problem, please contact your local BLACK+DECKER repair agents
Warning! Before proceeding, unplug the tool.

Appliance runs slowly

  •  Check that the spool housing can rotate freely Carefully clean It if necessary
  • Check that the cutting line does not protrude more than 11 cm from the spool housing If it does, cut 11 off so that it just reaches the line trimming blade.

If the bump feed does not work

  • Keep the tabs depressed and remove the spool cover from the housing.
  • Pull the cutting line until it protrudes 11 cm from the housing. If an insufficient cutting line Is left on the spool, install a new spool of cutting line as instructed above
  •  Align the tabs on the spool cover with the cutouts in the housing ., Push the cover onto the housing unUI It snaps securely into place.
  • If the culling line protrudes beyond the tomming blade, cut it off so that it Just reaches the blade tr the bump feed slill does not work or the spool is jammed, try the following suggestions:
  • Carefully clean the spool cover and housing.
  •  Remove the spool and check that the spring is in place.
  •  Remove the spool and unwind the cutting line, then wind It on neatly again as described above Replace the spool as instructed

Maintenance

Your BLACK+DECKER corded/cordless appliance/tool has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool appliance care and regular cleaning.

Warning! Before performing any maintenance on corded/ cordless power tools:

  • Switch off and unplug the appliance/tool.
  • Or switch off and remove the battery from the appliance/ tool if the appliance/tool has a separate battery pack.
  • Or run the battery down completely 1f it is integral and then switch it off.
  • Unplug the charger before cleaning 1t Your charger does not require any maintenance apart from regular cleaning.
  • Regularly clean the ventilation slots in your tool/appliance and charger using a soft brush or dry cloth.
  • Regularly clean the motor housing using a damp cloth. Do not use any abrasive or solvent-based cleaner

Protecting the environment

Separate collection. This product must not be disposed of with normal household waste. Should you find one day that your BLACK+DECKER product needs replacement, or if 1I is of no further use lo you, do not dispose of it with household waste. Make this product available for a separate collection of used products and ~<9 packaging allows materials to be recycled and used again. Re- use of recycled materials helps prevent environmental pollution and reduces the demand for raw materials. Local regulations may provide for separate collection of electrical products from the household, at municipal waste sites or by the retailer when you purchase a new product.

BLACK+DECKER provides a facility for the collection and recycling of BLACK+DECKER products once they have reached the end of their working life. To take advantage of this service please return your product to any authorized repair agent who will collect them on our behalf.You can check the location of your nearest authorized repair agent by contacting your local BLACK+DECKER office at the address indicated in this manual. Alternatively, a list of authorized BLACK+DECKER repair agents and full details of our after-sales service and contacts are available on the
Internet at: www.2helpU.com

Technical data

Hand/arm weighted vibration value according to EN 786: = 7,5 m/s2, uncertainty (K) = 1.5 m/s2 Lp, (sound pressure) 80 dB(A), uncertainly (K) = 1.5 dB(A)Level of acoustic power according to 2000/14/EC (Article 12, Annex 111, Ls 50 cm): t._.,. (measured sound power) 94 dB(A) uncertainty (K) = 1.5 dB(A) L,.,. (guaranteed sound power) 96 dB(A) uncertainty (K) = 1.5 dB(A)

These products also comply with Directive 2004/108/EC (until 19/04/2016) 2014/30/EU (from 20/0412016) and 2011 /65/EU. For more information, please contact Black & Decker al the
following address or refer lo the back of the manual. The undersigned is responsible for the compilation of the technical file and makes this declaration on behalf of Black & Decker.

Guarantee

Black & Decker 1s confident of the quality of its products and offers an outstanding guarantee. This guarantee statement is in addition to and in no way pre1ud1ces your statutory rights. The guarantee 1s valid \\1thin the! memories of the Member States of the European Union and the European Free Trade Area. If a Black & Decker product becomes defective due to faulty materials. workmanship or lack of conformity, within 24 months from the date of purchase. Black & Decker guarantees to replace defective parts, repair products subjected to fair wear and tear or replace such products to
ensure minimum inconvenience to the customer unless

  • The product has been used for trade, professional, or hires pull)Oses;

  • The product has been subjected to misuse or neglect.

  •  The product has sustained damage through foreign objects, substances, or accidents;

  • Repairs have been attempted by persons other than authorized repair agents or Black & Decker service staff.

  • To claim on the guarantee. you will need to submit proof of purchase to the seller or an authorized repair agent You can check the location of your nearest authorized repair agent
    by contacting your local Black & Decker office at the address indicated in this manual. Alternatively. a list of authorized

  • Black & Decker repair agents and full details of our aftersales service and contacts are available on the Internet at: www.2helpU.co

Please v1s1t our website www.blackanddecker.co.uk to register your new BLACK +DECKER product and to be kept up to date on new products and special offers Further information on the BLACK+DECKER brand and our range of products is available at www.blackanddecker.co.uk

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Black Decker User Manuals

Related Manuals